IllustrationMY 2016 SUBARU OUTBACK ALL OF SUDDEN HAD WARNING LIGHTS SUCH AS: BRAKE, ABS, AND STABILITY TRACTION CONTROL POPPED UP ON THE DASHBOARD WHEN THE CAR WAS IN PARK ANS WHEN I WAS DRIVING DOWN THE ROAD AND WILL NOT GO AWAY. IT HAS MADE MY STEERING WHEEL REALLY HARD TO TURN.
2016 Subaru Outback
Owner reports · Recalls · Investigations
More warning signs than most Outback years
Owner complaints for the 2016 Subaru Outback are substantially higher than the model-year median of 207.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Outback years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1290–25K
10925–50K
7450–75K
2075–100K
15100–150K
4150K+
351 reports with mileage · 292 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 309 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Visibility/wiper. Review the 83 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 53 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
22 crash reports3 fire reports8 injury reports
Electronic Stability Control (esc) complaints
5 reportsPROBLEM: 360 CCA BATTERIES INSTALLED IN NEW CARS ARE NOT ENOUGH AND THEY CAUSE PROBLEMS. MY FIRST INDICATION WAS A YEAR AGO WHEN I WENT TO THE STORE, WAS IN THERE 10-15 MINUTES, AND WHEN I CAME OUT THE CAR DID NOT START. A FRIEND CAME 2 HOURS LATER TO JUMP IT BUT TRIED IT FIRST AND IT STARTED RIGHT UP. SECOND PROBLEM WAS ON A…
Read full complaint
PROBLEM: 360 CCA BATTERIES INSTALLED IN NEW CARS ARE NOT ENOUGH AND THEY CAUSE PROBLEMS. MY FIRST INDICATION WAS A YEAR AGO WHEN I WENT TO THE STORE, WAS IN THERE 10-15 MINUTES, AND WHEN I CAME OUT THE CAR DID NOT START. A FRIEND CAME 2 HOURS LATER TO JUMP IT BUT TRIED IT FIRST AND IT STARTED RIGHT UP. SECOND PROBLEM WAS ON A TRIP TO DC IN NOVEMBER '18. NOR'EASTER CAME THROUGH AND WE GOT STUCK ON THE INTERSTATE IN THE MOUNTAINS FOR A FEW HOURS. CAR WAS STOPPED, NOT RUNNING. WENT TO GET DINNER THEN TO CAR TO GO ON AGAIN. WOULD NOT START. WERE STRANDED FOR 3 MORE HOURS, AS THE WEATHER AND MOUNTAIN DRIVE MADE IT IMPOSSIBLE TO GET HELP. WE WERE EVENTUALLY ABLE TO FIND SOMEONE TO JUMP IT. OVER NEXT FEW MONTHS, ODD THINGS HAPPENED LIKE THE RADIO NOT WORKING SPORATICALLY, SLOW STARTS, AND THE KEY NOT COMING OUT OF IGNITION OCCASIONALLY. TOOK IT TO THE DEALER, THEY RECOMMEND A $853 NEW SHIFT MECHANISM, BUT IN THE DISCUSSION HE HAPPENED TO MENTION THE 360CCA BATTERY NOT BEING ENOUGH FOR THE CAR. MY SUSPICIONS TELL ME TO GET A NEW BATTERY AND SEE HOW THINGS GO. GOT BATTERY- 640CCA, A WEEK AGO AND NO PROBLEMS AT ALL NOW. IT'S NOT RIGHT THAT THE DEALERS KNOW ABOUT THE BATTERY NOT BEING ENOUGH, AND WHEN YOU BRING THE CAR IN THEY TRY TO GET YOU TO PAY FOR LARGE DOLLAR FIX-IT'S AND AVOID TALKING ABOUT THE BATTERY ISSUE. I DON'T KNOW HOW MANY YEARS AND MAKES OF SUBARUS HAVE THESE, BUT PROB AT LEAST A FEW YEARS. THEY NEED TO RECALL AND PUT IN BETTER BATTERY, AT LEAST A $500CCA. I HAVE READ CAR GURU BLOG THAT MAKES IT OBVIOUS THAT AT LEAST HUNDREDS OF PEOPLE HAVE STORIES OF BEING STRANDED. FOR A LONG TIME OR IN A BAD PLACE. MY BATTERY COST ME $173 AND THEY SHOULD REFUND THAT TO ME.
DRIVING ON HIGHWAY IN 18F WEATHER WITH LIGHT SNOW AND PREVIOUSLY PLOWED ROAD. NO ISSUES DRIVING AROUND 50-60 MPH UNTIL PASSING UNDER A HIGHWAY OVERPASS. THE CAR TURNED INTO THE OTHER LANE AND THEN CORRECTED ITSELF. THIS KEPT ON HAPPENING AT ALMOST EVERY OVERPASS WE WENT UNDER. SLOWING DOWN REDUCED THE DEGREE OF VEERING BUT WE K…
Read full complaint
DRIVING ON HIGHWAY IN 18F WEATHER WITH LIGHT SNOW AND PREVIOUSLY PLOWED ROAD. NO ISSUES DRIVING AROUND 50-60 MPH UNTIL PASSING UNDER A HIGHWAY OVERPASS. THE CAR TURNED INTO THE OTHER LANE AND THEN CORRECTED ITSELF. THIS KEPT ON HAPPENING AT ALMOST EVERY OVERPASS WE WENT UNDER. SLOWING DOWN REDUCED THE DEGREE OF VEERING BUT WE KEPT EXPERIENCING THE WOBBLE EFFECT AS WE CROSSED UNDER EACH OVERPASS. ALMOST LIKE THE TRACTION CONTROL SYSTEM WAS "SLOW IN RESPONDING". TOOK TO THE DEALER BUT THEY REPORTED THAT THEY COULD NOT FIND ANY ISSUES WITH THE VEHICLE. DEALER SUGGESTED I BRING THE CAR IN AND HAVE A TECH RIDE WITH ME NEXT TIME THERE IS A SIMILAR WEATHER PATTERN.
THE EYESIGHT SYSTEM FAILED TO BRAKE THE CAR AUTOMATICALLY.
I JUST PICKED UP AND DROVE HOME. THE DRIVER MIRROR ALWAYS DETECTED - EVERY TIME. THE PASSENGER SIDE WOULD NOT ALWAYS DETECT , MAYBE MISSING 20-25%,EVEN SOME LARGE TRUCKS, I DID BRING BACK TO DEALER TWICE BUT THEY SAID CAN NOT DUPLICATE THE PROBLEM. THAT MADE ME NERVOUS IN THAT "THE TECHNOLOGY MIGHT LEAD TO AN ACCIDENT ,NOW THE …
Read full complaint
I JUST PICKED UP AND DROVE HOME. THE DRIVER MIRROR ALWAYS DETECTED - EVERY TIME. THE PASSENGER SIDE WOULD NOT ALWAYS DETECT , MAYBE MISSING 20-25%,EVEN SOME LARGE TRUCKS, I DID BRING BACK TO DEALER TWICE BUT THEY SAID CAN NOT DUPLICATE THE PROBLEM. THAT MADE ME NERVOUS IN THAT "THE TECHNOLOGY MIGHT LEAD TO AN ACCIDENT ,NOW THE CAR WAS 3200 MILES AND NOT WORK AT ALL WHEN I DROVE FROM MY HOUSE TO WORK THIS MORNING FROM RENTON TO REDMOND ON 405 WITH AVERAGE 50 MILE PER HOURS
Official recalls
419V910000 · Air Bags: Air Bag/restraint Control Module
Dec 19, 2019
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
16V292000 · Steering:column
May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
15V794000 · Power Train:driveline:differential Unit; Power Train:driveline:driveshaft
Nov 24, 2015
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
15V502000 · Power Train:automatic Transmission; Power Train:driveline:driveshaft
Aug 10, 2015
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.