← New search

2009 Scion Xb

Owner reports · Recalls · Investigations

More warning signs than most Xb years

Owner complaints for the 2009 Scion Xb are substantially higher than the model-year median of 45.

About this comparison →

When problems were reported

Mileage at the reported incident

71 reports with mileage · 69 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 74 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 24 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

12 crash reports5 fire reports12 injury reports

Electronic Stability Control (esc) complaints

4 reports
Clear category filter
97,000 miles · Feb 10, 2016
Electronic Stability Control (esc)EngineUnknown Or OtherFire

THE SCION XB 2009 WAS DRIVING ON THE HIGHWAY, AT SPEED LIMIT, 10 MILES AFTER THE "NEEDS MAINTENANCE" OIL LIGHT CAME ON. AFTER 15 MINUTES, THE CAR MADE A LOUD BANG NOISE WHICH WE THINK CAME FROM THE ENGINE.AFTER THE BANG, CAR PULLED OVER. ANOTHER CAR PULLED OVER TOO, SINCE A PIECE OF FLAMING DEBRIS FROM MY CAR CAME OUT FROM UNDER…

Read full complaint

THE SCION XB 2009 WAS DRIVING ON THE HIGHWAY, AT SPEED LIMIT, 10 MILES AFTER THE "NEEDS MAINTENANCE" OIL LIGHT CAME ON. AFTER 15 MINUTES, THE CAR MADE A LOUD BANG NOISE WHICH WE THINK CAME FROM THE ENGINE.AFTER THE BANG, CAR PULLED OVER. ANOTHER CAR PULLED OVER TOO, SINCE A PIECE OF FLAMING DEBRIS FROM MY CAR CAME OUT FROM UNDERNEATH AND BROKE THAT CAR'S WINDSHIELD. THAT DRIVER INDICATED THAT MY SCION WAS ON FIRE AND TO GET OUT OF THE CAR! ~5 SECONDS LATER THE FIRST OF MANY EXPLOSIONS HAPPENED. THE CAR QUICKLY, WITHIN ONE MINUTE, BECAME COMPLETELY ENGULFED IN FLAMES. BY THE TIME THE FIRE DEPARTMENT ARRIVED THE CAR WAS "FULLY ENGAGED" (100% BURNING). IT IS A TOTAL LOSS.

NHTSA ODI #10825501

126,000 miles · Jan 28, 2015
Air BagsElectronic Stability Control (esc)Seat BeltsCrashInjury

TRAVELING NORTH ON I-75 IN INDEPENDENCE TWP, MI SOUTH OF ORTONVILLE RD AT 10:55AM IN A SNOW STORM, DRIVER USED THE PASSING LANE TO OVERTAKE A SLOW MOVING VEHICLE IN THE CENTER LANE. ACCELERATING TO 70MPH, DRIVER BEGAN TO MERGE BACK INTO CENTER LANE BUT ENCOUNTERED A HEAVY BUILDUP OF SLUSH BETWEEN LANES AND BEGAN TO LOOSE TRACTIO…

Read full complaint

TRAVELING NORTH ON I-75 IN INDEPENDENCE TWP, MI SOUTH OF ORTONVILLE RD AT 10:55AM IN A SNOW STORM, DRIVER USED THE PASSING LANE TO OVERTAKE A SLOW MOVING VEHICLE IN THE CENTER LANE. ACCELERATING TO 70MPH, DRIVER BEGAN TO MERGE BACK INTO CENTER LANE BUT ENCOUNTERED A HEAVY BUILDUP OF SLUSH BETWEEN LANES AND BEGAN TO LOOSE TRACTION. VEHICLE STARTED TO VEER TO THE RIGHT. DRIVER REMOVED FOOT FROM THE ACCELERATOR AND TURNED WHEEL SLIGHTLY TO THE LEFT TO CORRECT THE SKID BUT THE ELECTRONIC STABILITY CONTROL ENGAGED AND THE VEHICLE IMMEDIATELY ENTERED INTO A RAPID 360 DEGREE SPIN TO THE RIGHT. NO OTHER VEHICLE WAS STRUCK. DRIVER RECOVERED FROM THE SPIN MOMENTARILY AND CAR WAS FACING NORTHBOUND BETWEEN THE CENTER AND RIGHT LANES BUT STILL VEERING TO THE RIGHT. THE FRONT WHEELS CONTACTED DRY PAVEMENT WHILE THE REAR WHEELS WERE ON WET PAVEMENT CAUSING THE VEHICLE TO MAKE A SHARP RIGHT TURN HEAD ON INTO THE GUARD RAIL AT 60 MPH. THE GUARD RAIL GAVE WAY AND THE FRONT END OF THE VEHICLE SUSTAINED HEAVY DAMAGE. HOWEVER THE VEHICLE REBOUNDED AND REMAINED IN THE ROAD WAY, SLIDING SIDEWAYS AND EVENTUALLY SPINNING ANOTHER 270 DEGREES AFTER AGAIN STRIKING THE GUARD RAIL. THE INITIAL HIGH SPEED IMPACT WITH GUARD RAIL APPEARS TO HAVE IGNITED THE SODIUM AZIDE AS EVIDENCED BY A GUNPOWDER LIKE ODOR IN THE VEHICLE HOWEVER NO AIRBAGS DEPLOYED. ADDITIONALLY, THE SEATBELT WHILE PROPERLY FASTENED DID NOT RETRACT AND RESTRAIN THE DRIVER. THE SEATBELT EXTENDED ALL THE WAY OUT AND REMAINED IN THIS POSITION. THIS MADE IT DIFFICULT TO CONTROL THE VEHICLE AND CAUSED THE DRIVER TO IMPACT THE STEERING WHEEL WHEN THE GUARDRAIL WAS STRUCK. THIS RESULTED IN INJURY TO THE RIGHT SIDE OF THE RIB CAGE, WITH POSSIBLE HAIRLINE FRACTURES TO THE RIBS, TORN MUSCLES, AND BRUISING OF THE LIVER. DRIVER'S HEAD ALSO IMPACTED THE CEILING. UPON SECOND GUARDRAIL IMPACT, DRIVER'S LEFT ARM IMPACTED THE STEERING WHEEL. *TR

NHTSA ODI #10679602

70,707 miles · Jan 7, 2014
Electronic Stability Control (esc)Equipment Adaptive/mobilityService Brakes

I TOOK THE VEHICLE TO MY DEALERSHIP BECAUSE I HAVE FOUR WARNING LIGHTS ILLUMINATED, THEY WERE BRAKE, TRACTION CONTROL, ABS, VSC. THE DEALER DIAGNOSED THE PROBLEM TO BE THE RIGHT REAR AND LEFT REAR ABS SENSORS AND CABLES WITH A REPLACEMENT COST OS $1357.04 PLUS DIAGNOSTIC FEE OF $59.66. I ASKED WHY THE SENSORS WERE DEFECTIVE AND …

Read full complaint

I TOOK THE VEHICLE TO MY DEALERSHIP BECAUSE I HAVE FOUR WARNING LIGHTS ILLUMINATED, THEY WERE BRAKE, TRACTION CONTROL, ABS, VSC. THE DEALER DIAGNOSED THE PROBLEM TO BE THE RIGHT REAR AND LEFT REAR ABS SENSORS AND CABLES WITH A REPLACEMENT COST OS $1357.04 PLUS DIAGNOSTIC FEE OF $59.66. I ASKED WHY THE SENSORS WERE DEFECTIVE AND NEEDED REPLACEMENT, THEY TOLD ME IT WAS DUE TO CORROSION FROM ROAD SALT. THIS SEEMS LIKE A MANUFACTURING ISSUE!! I'VE SEEN A SCION SERVICE BULLETIN (S-SB-0040-09 DATED JULY 6, 2009) THAT ADDRESSES THIS ISSUE. I HAVE ASKED THE DEALER AND SCION IF THEY COULD HELP ME OUT IN ANY WAY AND THEY'RE ANSWER WAS NO. I REALIZE MY CAR IS OUR OF WARRANTY BUT WHY SHOULD AN OWNER OF A VEHICLE HAVE TO SPEND $1400.00 TO REPLACE COMPONENTS THAT THE MANUFACTURE HAS SINCE CORRECTED THE DESIGN DUE TO THIS PROBLEM? *TR

NHTSA ODI #10558868

35,500 miles · Jan 6, 2012
Electronic Stability Control (esc)Traction Control SystemVehicle Speed Control

THE ISSUE I AM HAVING WITH MY VEHICLE IS THE TRACTION CONTROL. THERE IS NO WAY TO DISABLE IT PERMANENTLY. I HAVE CONTACTED THE MANUFACTURER SEVERAL TIMES TO RESOLVE THIS ISSUE BUT THEY WERE UNABLE TO HELP. THE INTERSECTION EXITING MY NEIGHBORHOOD IS OFTEN BUSY AND OCCASIONALLY THERE IS LOOSE SAND AND GRAVEL AT THE EXIT. AT T…

Read full complaint

THE ISSUE I AM HAVING WITH MY VEHICLE IS THE TRACTION CONTROL. THERE IS NO WAY TO DISABLE IT PERMANENTLY. I HAVE CONTACTED THE MANUFACTURER SEVERAL TIMES TO RESOLVE THIS ISSUE BUT THEY WERE UNABLE TO HELP. THE INTERSECTION EXITING MY NEIGHBORHOOD IS OFTEN BUSY AND OCCASIONALLY THERE IS LOOSE SAND AND GRAVEL AT THE EXIT. AT TIMES, TO CROSS THE INTERSECTION SAFELY, I WILL NEED TO STEP ON THE ACCELERATOR A LITTLE MORE THAN USUAL. IF MY TIRES SO HAPPEN TO BE SITTING ON A PATCH OF LOOSE SAND OR GRAVEL, THE TRACTION CONTROL WILL ACTIVATE WHEN I ACCELERATE. THIS CUTS THE POWER FROM MY ENGINE AND INSTEAD OF BRISKLY CROSSING THE INTERSECTION, MY CAR, AT A SNAILS PACE, CROSSES THE INTERSECTION. THE MORE TIME MY VEHICLE SPENDS IN THE INTERSECTION, THE GREATER CHANCE OF AN ACCIDENT. THE POWER IS CUT FOR TOO LONG IN MY OPINION AND I FEEL THAT MY VEHICLE WOULD BE MUCH SAFER WITHOUT IT. A LITTLE SPIN OF THE MY TIRES WOULD OCCUR WHEN I'M ON THE LOOSE SAND AND GRAVEL BUT ONCE ON NORMAL PAVEMENT, IT WOULD BE BUSINESS AS USUAL. WITH THE TRACTION CONTROL ACTIVATED, THERE IS A DELAY AND ONCE ON NORMAL PAVEMENT, IT STILL HAS REDUCED POWER. THE CAR DOES ALLOW THE DRIVER TO TURN OFF THE TRACTION CONTROL AT A STOP BUT IT REACTIVATES AFTER REACHING A CERTAIN SPEED. I DO NOT ALWAYS KNOW WHEN I HAPPEN TO STOP ON A PATCH OF LOOSE SAND AND GRAVEL AND I WON'T ALWAYS REMEMBER TO TURN OFF THE TRACTION CONTROL AT EVERY STOP. *TR

NHTSA ODI #10442632

Official recalls

10

19V741000 · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

Oct 17, 2019

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

Additional source detail variants (2)

Air Bags:frontal:passenger Side:inflator Module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

Air Bags:frontal:driver Side:inflator Module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

18V024000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2013 Scion xB, Toyota Corolla, Corolla Matrix, Sienna, 4Runner, Lexus IS250, IS350, IS250C, IS350C, IS-F, and GX460 vehicles sold, ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP (Saipan), and the U.S. VI or "Zone A." Toyota is also recalling certain 2010 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, 4Runner, Lexus IS250, IS350, IS250C, IS350C, ES350, IS-F, GX460, and Pontiac Vibe vehicles sold, ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Toyota is also recalling certain 2009 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, Lexus IS250, IS350, ES350, IS-F, and Pontiac Vibe vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the vehicle model, dealers will replace the front passenger air bag inflator, or replace the air bag assembly. The recall began on January 29, 2018. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for this recall are "Zone A" Toyota: G0P, Lexus: GLG; "Zone B" Toyota: G0R, Lexus GLH; "Zone C" Toyota: H0A, and Lexus: HLA.

17V006000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2017

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2012 Toyota 4Runner, Corolla, Corolla Matrix, Sienna, Yaris, Scion xB, Lexus ES350, GX460, IS-F, IS250, IS350, IS250C, IS350C, and Lexus LFA vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain 2009 Toyota Corolla, Corolla Matrix, Yaris, Yaris HB, Scion xB, Pontiac Vibe, Lexus, ES350, IS250, IS350, and IS-F vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Toyota is recalling certain 2006-2008 Lexus IS250 and IS350, 2007-2008 Lexus ES350, Toyota Yaris, Yaris HB, and 2008 Lexus IS-F and Scion xB vehicles originally sold, or ever registered in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on February 1, 2017. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), H0A (Toyota Zone C), GLG (Lexus Zone A), GLH (Lexus Zone B) and HLA (Lexus Zone C).

16V340000 · Air Bags:frontal:passenger Side:inflator Module

May 23, 2016

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2011 Scion xB and Lexus IS F, 2009-2011 Toyota Corolla and Corolla Matrix, 2006-2011 Toyota Yaris, Lexus IS250 and Lexus IS350, 2010-2011 Toyota 4Runner, Lexus IS250C, Lexus IS350C and Lexus GX460, 2011 Sienna, 2007-2011 Lexus ES350, and 2009-2010 Pontiac Vibe vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain model year 2008 Scion xB and Lexus IS F, 2007-2008 Toyota Yaris, 2006-2008 Lexus IS250 and Lexus IS350 and 2007-2008 Lexus ES350 vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on December 6, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for interim notification for this campaign are G1P (Toyota Zone A), G1R (Toyota Zone B), G2G (Lexus Zone A), and G2H (Lexus Zone B). Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), GLG (Lexus Zone A), and GLH (Lexus Zone B).

15V689000 · Visibility:power Window Devices And Controls

Oct 22, 2015

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Consequence & remedy

Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.

12V491000 · Visibility:power Window Devices And Controls

Oct 10, 2012

Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.

Consequence & remedy

Consequence: If the switch overheats, it may melt, possibly resulting in a fire.

Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.

10V035000 · Equipment:other:labels

Feb 3, 2010

GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.

Consequence & remedy

Consequence: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.

Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.

10V036000 · Equipment:other:labels

Feb 3, 2010

SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.

Consequence & remedy

Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.

Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.

09V223000 · Equipment:other:labels

Jun 15, 2009

TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."

Consequence & remedy

Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.

Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.

08V451000 · Structure:body:hood:hinge And Attachments

Sep 5, 2008

SOUTHEAST TOYOTA IS RECALLING 67 MY 2008-2009 SCION XB VEHICLES EQUIPPED WITH THE SPORTS GRILL OPTION AND ALSO SEVERAL RADIATOR GRILLS SOLD AS PARTS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 113, "HOOD LATCH SYSTEM." IT HAS BEEN DETERMINED THAT SHOULD THE PRIMARY HOOD LATCH BE RELEASED OR FAIL, THE PLASTIC UPPER RADIATOR GRILL GARNISH COULD RELEASE THE SECONDARY LATCH AND CAUSE THE HOOD TO OPEN.

Consequence & remedy

Consequence: DURING VEHICLE OPERATION, THIS COULD OBSTRUCT THE VIEW OF THE DRIVER POSSIBLY CAUSE THE HOOD TO STRIKE THE ROOF OR THE WINDSHIELD INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE SPORTS GRILL INSTALLATION AND INSTALL ADDITIONAL CLIPS TO ENSURE THE RADIATOR GRILL GARNISH IS PROPERLY SECURED. THE RECALL BEGAN ON OCTOBER 6, 2008. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.