Illustrationdriver side seat belt not retracting, there is a recall but does not include this vin number.
2011 Saab 9-3
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2011 Saab 9-3 do not stand out strongly from the model-year median of 61.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all 9-3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 7 of 30 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Seat Belts. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports0 fire reports0 injury reports
What owners actually said
30 reportsDRIVERS SIDE AIRBAG SPONTANEOUSLY DEPLOYED WHILE IN MOTION ON A CITY STREET GOING IN A FORWARD, STRAIGHT MOTION.
TL* THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT STATED THAT WHILE DRIVING, THE AIR BAG SENSOR WARNING LIGHT REMAINED ILLUMINATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO WAS UNABLE TO DETERMINE THE CAUSE OF THE FAILURE. THE MANUFACTURER AND LOCAL DEALER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 103,…
Read full complaint
TL* THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT STATED THAT WHILE DRIVING, THE AIR BAG SENSOR WARNING LIGHT REMAINED ILLUMINATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO WAS UNABLE TO DETERMINE THE CAUSE OF THE FAILURE. THE MANUFACTURER AND LOCAL DEALER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 103,000.
TL* THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT DETECTED A STRONG ODOR OF COOLANT INSIDE THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO STATED THAT THE VEHICLE WAS LEAKING COOLANT AND SCREWS WERE MISSING THAT CONNECTED THE TRANSMISSION TO THE MOTOR. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER AND DEALER W…
Read full complaint
TL* THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT DETECTED A STRONG ODOR OF COOLANT INSIDE THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO STATED THAT THE VEHICLE WAS LEAKING COOLANT AND SCREWS WERE MISSING THAT CONNECTED THE TRANSMISSION TO THE MOTOR. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER AND DEALER WERE NOT MADE WARE OF THE FAILURE. THE FAILURE MILEAGE WAS 120,000.
PUMP ON REAR XWD FAILURE
LETTER IS RESPONSE TO THE RECALL OF A DEFECTIVE AIR BAG; SEEKING HELP FOR THIS DILEMNA NHTSA CAMPAIGN ID NUMBER 16V063. *LD THE CONSUMER STATED THE RECALL EXCEEDED A REASONABLE AMOUNT OF TIME. UPDATED 06/29/2017 *JS
TL* TAKATA RECALL. THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER WAS NOT CONTACTED. THE MANUFA…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS CONTACTED AT 800-955-9007. THE CONTACT ASKED THE MANUFACTURER TO HAVE THE DEALER NEARBY REPAIR THE AIR BAGS. THE MANUFACTURER REFERRED THE CONTACT TO DEALER THAT WAS 60 MILES AWAY FROM THE CONTACT'S RESIDENCE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.
TL* TAKATA RECALL. THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. DORSHAL AUTOMOTIVE WAS CONTACTED AND CON…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. DORSHAL AUTOMOTIVE WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND INITIALLY INFORMED THE CONTACT THAT THE PART WAS BEING SENT; HOWEVER, THE CONTACT STILL WAS NOT ABLE TO GET THE RECALL REMEDIED DUE TO THE LACK OF PART AVAILABILITY. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT. UPDATED 08/29/17*LJ *CN
TAKATA RECALL. THE RECALL ISSUE HAS BEEN KNOWN FOR SEVERAL YEARS NOW YET NO REMEDY IS AVAILABLE FOR THIS MODEL VEHICLE. CONSIDERING THE DANGER AND GRAVITY BEHIND THIS KNOWN ISSUE, IT IS UNACCEPTABLE THAT A REMEDY IS NOT AVAILABLE FOR ALL VEHICLES TO ENSURE THE SAFETY THE PERSONS INVOLVED.
TL* TAKATA RECALL. THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT STATED THAT THE RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 16V063000(AIR BAGS) WAS RECEIVED IN FEBRUARY OF 2016. AFTER CONTACTING THE DEALER AND THE MANUFACTURER ON MULTIPLE OCCASIONS, THE CONTACT WAS INFORMED THAT THE PARTS NEEDED FOR THE RECALL REMEDY WERE STILL NO…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2011 SAAB 9-3. THE CONTACT STATED THAT THE RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 16V063000(AIR BAGS) WAS RECEIVED IN FEBRUARY OF 2016. AFTER CONTACTING THE DEALER AND THE MANUFACTURER ON MULTIPLE OCCASIONS, THE CONTACT WAS INFORMED THAT THE PARTS NEEDED FOR THE RECALL REMEDY WERE STILL NOT AVAILABLE AND NO ESTIMATED TIME FOR RECEIVING THE PARTS COULD BE PROVIDED. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
Official recalls
316V063000 · Air Bags:frontal:driver Side:inflator Module
Feb 3, 2016
General Motors LLC (GM) is recalling certain model year 2006-2011 Saab 9-3 vehicles manufactured May 31, 2002, to February 15, 2011, 2006-2009 Saab 9-5 vehicles manufactured June 7, 2005, to May 28, 2009, and 2008-2009 Saturn Astra vehicles manufactured April 11, 2007, to July 24, 2008. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the driver's frontal air bag inflator on Saab 9-3 and 9-5 vehicles and will replace the driver's frontal airbag module on Saturn Astra vehicles, free of charge. The recall began on March 1, 2017. Owners may contact Saab customer service at 1-800-955-9007 or Saturn customer service at 1-800-553-6000. GM's number for this recall is 28810.
14V318000 · Seat Belts:front:retractor
Jun 12, 2014
General Motors LLC (GM) is recalling certain model year 2004-2011 Saab 9-3 Convertible vehicles manufactured July 30, 2003, to February 15, 2011. In the affected vehicles, the driver's side front seat belt retractor may break, causing the seat belt webbing not to retract.
Consequence & remedy
Consequence: In the event of a crash, a seat belt that has not retracted may not properly restrain the seat occupant, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver's seat belt retractor, free of charge. The recall began on October 6, 2015. Owners may contact Saab customer service at 1-800-955-9007. GM's number for this recall is 14222. Note: Special Coverage 10086 will replace the passenger side seat belt retractor if it fails, free of charge, for the life of the vehicle.
11V015000 · Fuel System, Other:delivery:fuel Pump
Jan 19, 2011
SAAB IS RECALLING CERTAIN MODEL YEAR 2010 AND 2011 PASSENGER VEHICLES MANUFACTURED FROM JUNE 2010 THROUGH DECEMBER 2010. CERTAIN FUEL PUMPS INSTALLED AS ORIGINAL EQUIPMENT MAY HAVE INTERNAL COMPONENTS WITH INCORRECT SPECIFICATIONS.
Consequence & remedy
Consequence: THE SUBJECT FUEL PUMPS CAN SEIZE CAUSING THE ENGINE TO STALL WHICH INCREASES THE RISK OF A CRASH.
Remedy: SAAB WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMPS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 3, 2011. OWNERS MAY CONTACT SAAB AT 1-800-955-9007.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.