My 2017 Porsche Macan has a Timing Chain Cover Bolt Failure which has caused leaking oil and may lead to total loss of oil and engine failure. This is a known documented design and manufacturing defect affecting the 3.0L and 3.6L engines. The manufacturers original aluminum bolts for the cover suffer from premature failure leadi…
Read full complaint
My 2017 Porsche Macan has a Timing Chain Cover Bolt Failure which has caused leaking oil and may lead to total loss of oil and engine failure. This is a known documented design and manufacturing defect affecting the 3.0L and 3.6L engines. The manufacturers original aluminum bolts for the cover suffer from premature failure leading them to break. Porsche has recognized this widespread defect and problem by issuing a technical service bulletin for this issue. Porsche has not issued a recall to fix this problem. I have contacted a Porsche dealer to address this problem but they refused to make the repair without my paying the cost to repair their defect.
NHTSA ODI #11752140
Mileage unknown · Apr 14, 2025
Engine
Porsche is making use of aluminum fasteners for important engine components. These fasteners are substandard for the service. At 100,000 miles, two of the bolts for the timing chain cover simply broke in half during normal service, resulting in a substantial oil leak and an expensive repair (about $3000). At 120,000 miles, one o…
Read full complaint
Porsche is making use of aluminum fasteners for important engine components. These fasteners are substandard for the service. At 100,000 miles, two of the bolts for the timing chain cover simply broke in half during normal service, resulting in a substantial oil leak and an expensive repair (about $3000). At 120,000 miles, one of the bolts for the valve cover also simply broke in half, resulting in another oil leak and a repair bill of about $1000.
NHTSA ODI #11654627
Mileage unknown · Mar 14, 2024
Air BagsEngine
airbag light comes on and off intermittently I am aware there were some problems with the airbag sensor that year and recalls for other models, not my vin, I have called and confirmed there are none for mine. seems to act up more after or while I have a passenger so I suspect (almost positive) this is for the passenger airbag. a…
Read full complaint
airbag light comes on and off intermittently I am aware there were some problems with the airbag sensor that year and recalls for other models, not my vin, I have called and confirmed there are none for mine. seems to act up more after or while I have a passenger so I suspect (almost positive) this is for the passenger airbag. also when I have a passenger the amber indicator that says airbag on off will randomly switch to off and I'll get the dash light. this makes me think its the airbag weight sensor pad that deteriorates easily that other cars had a recall for but not mine. no water was spilled on the seat before it started acting up the way it has been. as well, the engine motor mounts have a tendency to break fairly easily and fast causing vibrations and possible safety issues.
NHTSA ODI #11577431
Mileage unknown · May 8, 2023
Engine
The 2017 Porsche Macan S is unsafe to drive on the road as the vehicle goes into jerking mode while driving without any warning, the safety light came on as transmission fault. I took the vehicle to River Oaks Porsche, and they diagnosed the issue as transmission problem common with the Macan brand and the Cayenne brand, I then …
Read full complaint
The 2017 Porsche Macan S is unsafe to drive on the road as the vehicle goes into jerking mode while driving without any warning, the safety light came on as transmission fault. I took the vehicle to River Oaks Porsche, and they diagnosed the issue as transmission problem common with the Macan brand and the Cayenne brand, I then informed the manufacturer, and I was informed that since the vehicle had not been recalled there was nothing they could do with the defect. Since the dealership acknowledged that the issue was common with these brands, I believed that these vehicles should have been recalled for public safety.
NHTSA ODI #11521025
Mileage unknown · Jun 3, 2022
Engine
The engine oil started leaking on the timing case over bolts. The current mileage is 20500. This happened right after the regular 40,000 mile maintenance. The dealership said it's out of warranty but on a bit of research the aluminum bolts seem to break easily with a lot of similar cases.
NHTSA ODI #11467288
Mileage unknown · May 30, 2021
Engine
On April 26 2021 performed routine oil change and noticed oil leaking from valve cover gasket onto side of engine. Took to Prestige Imports Inc, in Lakewood Colorado April 30th 2021, mileage is 22,851 and dealer told me: "Inspect for engine oil leak, no leak present although a slight wetness is visible at valve cover, no drips …
Read full complaint
On April 26 2021 performed routine oil change and noticed oil leaking from valve cover gasket onto side of engine. Took to Prestige Imports Inc, in Lakewood Colorado April 30th 2021, mileage is 22,851 and dealer told me: "Inspect for engine oil leak, no leak present although a slight wetness is visible at valve cover, no drips present. No repairs necessary per Porsche warranty guidelines." Dealer advised me to drive car hard and return in few weeks for visual inspection. Returned to dealer on 05/19/2021 and dealer looked at car and told me leak was a SWEAT and would not be repaired under warranty. Car purchased 05/22/2021, out of warranty 05/22/2021.
NHTSA ODI #11419063
70,000 miles · Dec 2, 2020
Engine
PER PORSCHE DEALER, "2 BROKER BOLTS ON THE TIMING COVER CAUSING AN OIL LEAK." VERY, VERY EXPENSIVE (THOUSANDS OF DOLLARS) TO REPAIR AS VEHICLE IS 50 MONTHS OLD. NO RECALL JUST YET BY PORSCHE PER DEALER, THOUGH HAS AFFECTED PORSCHE CARS WITH THIS ENGINE IN SIGNIFICANT NUMBERS AS IS READILY NOTED ON ONLINE FORUMS AND ACKNOWLEDGE…
Read full complaint
PER PORSCHE DEALER, "2 BROKER BOLTS ON THE TIMING COVER CAUSING AN OIL LEAK." VERY, VERY EXPENSIVE (THOUSANDS OF DOLLARS) TO REPAIR AS VEHICLE IS 50 MONTHS OLD. NO RECALL JUST YET BY PORSCHE PER DEALER, THOUGH HAS AFFECTED PORSCHE CARS WITH THIS ENGINE IN SIGNIFICANT NUMBERS AS IS READILY NOTED ON ONLINE FORUMS AND ACKNOWLEDGED BY DEALER.
NHTSA ODI #11377569
14,000 miles · Sep 24, 2018
Engine
TL* THE CONTACT OWNS A 2017 PORSCHE MACAN. WHILE DRIVING APPROXIMATELY 50 MPH, THE VEHICLE LOST POWER AND THE "ENGINE CONTROL FAULT" INDICATOR ILLUMINATED. THE CONTACT PULLED THE VEHICLE OVER TO THE SIDE OF THE ROAD AND SHUT OFF THE ENGINE. ONCE RESTARTED, THE VEHICLE OPERATED NORMALLY. THE CONTACT ALSO STATED THAT THE FAILURE O…
Read full complaint
TL* THE CONTACT OWNS A 2017 PORSCHE MACAN. WHILE DRIVING APPROXIMATELY 50 MPH, THE VEHICLE LOST POWER AND THE "ENGINE CONTROL FAULT" INDICATOR ILLUMINATED. THE CONTACT PULLED THE VEHICLE OVER TO THE SIDE OF THE ROAD AND SHUT OFF THE ENGINE. ONCE RESTARTED, THE VEHICLE OPERATED NORMALLY. THE CONTACT ALSO STATED THAT THE FAILURE OCCURRED FOUR OTHER TIMES. THE VEHICLE WAS TAKEN TO THE DEALER (GARBER AUTOMOTIVE ROCHESTER, 3955 W HENRIETTA ROAD, ROCHESTER, NY 14623) ON SIX OCCASIONS, BUT THEY WERE NOT ABLE TO DUPLICATE THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 14,000.
Porsche Cars North America, Inc. (Porsche) is recalling certain 2016-2020 Macan S, 2017-2020 Macan, 2017 Panamera Turbo, 2018 and 2020 Macan Turbo and Panamera 4, 2018 Macan Sport Edition, Panamera 4 E-Hybrid, and 2019 Panamera 4 Sport Turismo vehicles. The screw that attaches the lower seat belt anchor to the seat frame on the outboard rear seats may not have been tightened properly.
Consequence & remedy
Consequence: An improperly tightened seat belt anchor can detach during a crash, increasing the risk of injury.
Remedy: Dealers will replace and tighten the lower rear outboard seat belt anchor screws, free of charge. Owner notification letters are expected to be mailed August 24, 2023. Owners may contact Porsche's customer service at 1-800-767-7243. Porsche's number for this recall is APA9.
Porsche Cars North America, Inc. (Porsche) is recalling certain 2017-2018 Macan, Macan Turbo Kits, Macan GTS, 2015-2018 Macan S, and Macan Turbo vehicles. The front passenger seat occupancy sensor mat may degrade and fail to detect a passenger in the front seat.
Consequence & remedy
Consequence: The air bag will not deploy during a crash if a front passenger is undetected, increasing the risk of injury.
Remedy: Porsche will notify owners, and dealers will replace the sensor mat and seat cushion, free of charge. Owner notification letters were mailed October 25, 2021. Owners may contact Porsche customer service at 1-800-767-7243. Porsche's number for this recall is AMA2.
Porsche Cars North America, Inc. (Porsche) is recalling certain 2015-2018 Macan vehicles. The fuel pump service cover may contact the flow nozzle on the filter flange of the fuel pump, potentially causing cracks and a fuel leak.
Consequence & remedy
Consequence: Fuel leakage in the presence of an ignition source may increase the risk of a fire.
Remedy: Porsche will rework or replace and apply a protective film to the fuel pump flange. in addition, the fuel pump flange will be inspected and replaced if cracks are present. The recall began April 10, 2020. Owners may contact Porsche customer service at 1-800-767-7243. Porsche's number for this recall is ALA2.
Porsche Cars North America, Inc. (Porsche) is recalling certain 2017 Porsche Cayenne Turbo S, Cayenne Turbo, Cayenne Plug-in Hybrid, Cayenne GTS, Cayenne Plug-in Hybrid Platinum Edition, Macan Turbo and Macan GTS vehicles, 2017-2018 Cayenne S, Macan, Cayenne Platinum Edition and Macan S vehicles and 2018 Cayenne vehicles equipped with the optional ski bag. The ski bag fastening strap may have been sewn with incorrect thread, possibly resulting in the strap seams tearing and the ski bag being unsecured in the event of a crash.
Consequence & remedy
Consequence: If the ski bag detaches during a crash, it can increase the risk of injury.
Remedy: Porsche will notify owners, and dealers will replace the ski bags, free of charge. The recall began January 10, 2019. Owners may contact Porsche customer service at 1-800-767-7243. Porsche's number for this recall is AJ12.
Porsche Cars North America, Inc. (Porsche) is recalling certain 2015-2017 Macan S and Macan Turbo vehicles, and 2017 Macan, Macan Turbo with the Performance Package, and Macan GTS vehicles. The fuel pump flange on the affected vehicles may crack, allowing fuel to leak.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Porsche will notify owners, and dealers will inspect the flanges, replacing any that are cracked. Flanges that aren't cracked will have a protective film applied. These repairs will be performed free of charge. The recall began on July 19, 2017. Owners may contact Porsche customer service at 1-800-767-7243. Porsche's number for this recall is AH06.
Porsche Cars North America, Inc. (Porsche) is recalling certain model year 2017 Macan, Macan S, Macan GTS, and Macan Turbo vehicles. In the affected vehicles, the anti-rollbar connecting links may move out of position allowing the vehicle to oversteer in certain driving conditions.
Consequence & remedy
Consequence: Vehicle oversteer may lead to a loss of vehicle control, increasing the risk of a crash.
Remedy: Porsche will notify owners, and dealers will inspect, and as necessary, replace the front anti-rollbar links, free of charge. The recall began January 2017. Owners may contact Porsche customer service at 1-800-767-7243. Porsche's number for this recall is AG06.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2017 Porsche Macan Problems, Complaints & Recalls | Skip That Year
Illustration