Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
60–25K
1225–50K
450–75K
075–100K
0100–150K
0150K+
22 reports with mileage · 0 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Engine. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Engine And Engine Cooling. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Power Train. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
22 reports
29,000 miles · Apr 17, 2013
Engine
I APPROACHED MY PORSCHE 911 TURBO IN MY GARAGE AND NOTICED A SLIGHT BIT OF LIQUID WITH A PINK HUE (COOLANT) THAT HAD APPEARED TO HAVE LEAKED FROM UNDER MY CAR. I LOOKED AT THE COOLANT RESERVOIR WHICH WAS ~1.5-2 INCHES BELOW THE MAX FILL LINE. I DECIDED TO TAKE IT TO NEW GERMAN PERFORMANCE TO GET CHECKED OUT. I CALLED AND CONFIRM…
Read full complaint
I APPROACHED MY PORSCHE 911 TURBO IN MY GARAGE AND NOTICED A SLIGHT BIT OF LIQUID WITH A PINK HUE (COOLANT) THAT HAD APPEARED TO HAVE LEAKED FROM UNDER MY CAR. I LOOKED AT THE COOLANT RESERVOIR WHICH WAS ~1.5-2 INCHES BELOW THE MAX FILL LINE. I DECIDED TO TAKE IT TO NEW GERMAN PERFORMANCE TO GET CHECKED OUT. I CALLED AND CONFIRMED THEY HAD AN AVAILABILITY. I TURNED ON MY CAR AND SHORTLY THERE AFTER A WARNING POPPED UP STATING "CHECK COOLANT". THE DRIVE WAS ROUGHLY 20 MILES. THE ENGINE TEMPERATURE NEVER WENT ABOVE 175 DEGREES (NORMAL OPERATING TEMP) AND THE OIL NEVER WENT ABOVE THE 190S (AGAIN, TOTALLY NORMAL). I PARKED AND WENT INSIDE, HANDED OVER THE KEYS, AND 5 MINUTES LATER THE CAR HAD PUKED COOLANT OUT THE BACK. NGP RE-PINNED THE HOSE TO THE RADIATOR AND TOPPED OFF THE TANK. 2 MONTHS LATER (13APR2013) I WENT TO MY GARAGE AND AGAIN NOTICED A SMALL AMOUNT OF COOLANT ON THE FLOOR. I IMMEDIATELY CALLED NGP, CONFIRMED AVAILABILITY, AND TOOK THE CAR IN AGAIN. I WAS TOLD THE COOLANT HOSES WERE EPOXIED IN AND HAD BLOWN OUT. I WAS TOLD THAT THIS IS A WELL-KNOWN ISSUE AND THE HOSES MUST BE EITHER RE-EPOXIED, PINNED IN, OR WELDED (THE SAFEST OPTION). *TR
NHTSA ODI #10508623
1,000 miles · Dec 27, 2010
Fuel System, Gasoline
THE PROBLEM WITH MY 2007 PORSCHE TURBO IS THAT WHEN I GO TO FILL UP GAS THE TANK WILL NOT FILL PASS 2/3 OF THE TANK. THE PROBLEM HAPPENS MOST OF THE TIMES THAT I FILL UP GAS AND PORSCHE HAS TOLD ME THAT THERE IS NO FIX TO THE PROBLEM. I AM SURE THAT IT IS NOT ONLY MY CAR THAT HAS THIS PROBLEM AS I HAVE SEARCHED ON THE INTERNET A…
Read full complaint
THE PROBLEM WITH MY 2007 PORSCHE TURBO IS THAT WHEN I GO TO FILL UP GAS THE TANK WILL NOT FILL PASS 2/3 OF THE TANK. THE PROBLEM HAPPENS MOST OF THE TIMES THAT I FILL UP GAS AND PORSCHE HAS TOLD ME THAT THERE IS NO FIX TO THE PROBLEM. I AM SURE THAT IT IS NOT ONLY MY CAR THAT HAS THIS PROBLEM AS I HAVE SEARCHED ON THE INTERNET AND HAVE FOUND OTHERS WITH SIMILAR ISSUES. OUT OF THE MANY TIMES I HAVE TAKEN THE VEHICLE IN FOR SERVICE ONE TIME THEY CHANGE THE GAS TANK AND RELATING PARTS BUT IT DID NOT FIX THE ISSUE. *TR
NHTSA ODI #10372521
Official recalls
0
No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
2007 Porsche 911 Turbo Problems, Complaints & Recalls | Skip That Year
Illustration