Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
60–25K
1225–50K
450–75K
075–100K
0100–150K
0150K+
22 reports with mileage · 0 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Engine. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Engine And Engine Cooling. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Power Train. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
22 reports
73,696 miles · Mar 28, 2017
Engine
PURCHASED VEHICLE FROM PORSCHE DEALER ON JAN 2 2017 AND OPERATED IT 1600 MILES BEFORE IT BLEW A COOLANT FITTING AND EXPELLED COOLANT ALL OVER THE ROAD , REAR TIRE, AND REAR OF CAR. I WAS ON A BUSY INTERSTATE ON RAMP AND HEARD THE BELTS SQUEAL AND SAW STEAM IN THE REAR VIEW MIRROR. I COULD HAVE VERY EASILY LOST TRACTION IF THERE …
Read full complaint
PURCHASED VEHICLE FROM PORSCHE DEALER ON JAN 2 2017 AND OPERATED IT 1600 MILES BEFORE IT BLEW A COOLANT FITTING AND EXPELLED COOLANT ALL OVER THE ROAD , REAR TIRE, AND REAR OF CAR. I WAS ON A BUSY INTERSTATE ON RAMP AND HEARD THE BELTS SQUEAL AND SAW STEAM IN THE REAR VIEW MIRROR. I COULD HAVE VERY EASILY LOST TRACTION IF THERE WERE NO CARS AHEAD OF ME GOING SLOW. LUCKILY WAS ABLE TO PULL OVER IMMEDIATELY AND TURN THE CAR OFF BEFORE CAUSING ENGINE DAMAGE. NO ONE BEHIND ME LOST TRACTION IN THE SLICK COOLANT FORTUNATELY . EXTREMELY DANGEROUS CONDITION THAT COULD EASILY CAUSE A SERIOUS ACCIDENT. HAD VEHICLE TOWED TO SELLING DEALER 3 DAYS OUT OF WARRANTY AND RECEIVED AN ESTIMATE OF $5200 TO REPAIR A COOLANT HOSE. OFFERED A 15% DISCOUNT, THEN AN ADDITIONAL $1000 OFF. I RESEARCHED THE COMMON COOLANT FITTING ISSUE WHERE THE EPOXIED FITTING COMES LOOSE OR ONE OF THE PLASTIC FITTINGS BREAK. THE SERVICE MANAGER ACTED LIKE HE HAD NEVER HEARD OF THAT AND SAID THEY WOULD REPLACE THE ONE HOSE . DECLINED REPAIR AND HAD VEHICLE TOWED TO INDEPENDENT SHOP WHERE IT WAS DISCOVERED THAT IT WAS A FITTING , NOT A HOSE AS THE SERVICE ADVISOR HAD STATED. ONE OTHER FITTING WAS ABOUT TO FAIL AS WELL. THIS LARGE WELL KNOWN SHOP PERFORMS UPGRADES TO THESE FITTINGS BY WELDING THEM SO THEY WON'T LET GO. $5000 TO FIX ALL SEVEN FITTINGS. WELD 5 ALUMINUM FITTINGS AND REPLACE THE 2 PLASTIC ONES WITH ALUMINUM AND WELD THEM ALSO. DEFINITELY A DESIGN FLAW THAT COULD PUT A DRIVER AND OTHERS IN A BAD SITUATION. BEEN WITHOUT THE CAR FOR OVER 3 WEEKS SO FAR .
NHTSA ODI #10969029
36,000 miles · Feb 5, 2017
Engine
MAJOR COOLANT LEAK ON TOP OF ENGINE ..ENGINE MUST COME OUT $6000 EST AT PORSCHE DEALER. COMMON PROBLEM I TOLD..PORSCHE SHOULD RECALL THIS ISSUE!!
NHTSA ODI #10949636
61,556 miles · Oct 7, 2014
Engine
I PURCHASED THIS VEHICLE LISTED ABOVE 2007 PORSCHE 911 TURBO ON MONDAY SEPTEMBER 15TH 2014 FROM CARLSTADT NEW JERSEY. I BEGAN TO DRIVE THE VEHICLE BACK TO WHERE I CURRENTLY LIVE IN SUMMERVILLE, SC. APPROXIMATELY 30 MINUTES INTO THE DRIVE A LIGHT CAME ON IN THE GAUGE WHICH SAID COOLANT FAILURE. I IMMEDIATELY PULLED THE VEHICLE OV…
Read full complaint
I PURCHASED THIS VEHICLE LISTED ABOVE 2007 PORSCHE 911 TURBO ON MONDAY SEPTEMBER 15TH 2014 FROM CARLSTADT NEW JERSEY. I BEGAN TO DRIVE THE VEHICLE BACK TO WHERE I CURRENTLY LIVE IN SUMMERVILLE, SC. APPROXIMATELY 30 MINUTES INTO THE DRIVE A LIGHT CAME ON IN THE GAUGE WHICH SAID COOLANT FAILURE. I IMMEDIATELY PULLED THE VEHICLE OVER AND TURN THE CAR OFF. I OPENED THE REAR HATCH WHERE THE ENGINE IS HOUSED TO REVEAL STEAM POURING FROM THE BACK OF THE CAR. I CALLED AAA TO HAVE THE CAR TOWED TO THE NEAREST PORSCHE DEALERSHIP OFF THE NEW JERSEY INTERSTATE WHICH HAPPENED TO BE RAY CATENA PORSCHE OF EDISON NEW JERSEY. THE DEALERSHIP HAS VERIFIED THAT INDEED IT WAS A COOLANT FAILURE WHICH HAPPENS ON MODELS WITH GT1 ENGINE BLOCKS INCLUDING MY VEHICLE ABOVE. THE COOLANT FAILURE RESULTING IN ME ALMOST LOSING CONTROL OF THE VEHICLE AND COLLIDING WITH ANOTHER VEHICLE. PORSCHE OF NORTH AMERICA IS REFUSING TO ACKNOWLEDGE THIS AS AN ISSUE ON THESE VEHICLES WHICH IS WHY I'M FILING A COMPLIANT. MY VEHICLE IS PRESENTLY STILL BEING DIAGNOSE FURTHER BY THE DEALER TO SEE IF ANY ADDITIONAL DAMAGE HAS BEEN DONE TO THE MOTOR, WHICH HAS LEFT ME WITHOUT MY VEHICLE FOR OVER THREE WEEKS.
NHTSA ODI #10641993
32,152 miles · Jun 11, 2014
Engine
I NOTICED A SMALL COOLANT LEAK FROM THE REAR DRIVERS SIDE OF THE ENGINE. THIS LEAK BECAME MORE PROMINENT OVER THE NEXT SEVERAL DAYS. I TOOK MY CAR TO THE SHOP TO HAVE IT EVALUATED AND IT WAS DETERMINED THAT 4 OUT OF 6 COOLANT FITTINGS WERE LEAKING. THE DESIGN FROM PORSCHE HAS THE COOLANT HOSES AFFIXED USING AN EPOXY. AFTER M…
Read full complaint
I NOTICED A SMALL COOLANT LEAK FROM THE REAR DRIVERS SIDE OF THE ENGINE. THIS LEAK BECAME MORE PROMINENT OVER THE NEXT SEVERAL DAYS. I TOOK MY CAR TO THE SHOP TO HAVE IT EVALUATED AND IT WAS DETERMINED THAT 4 OUT OF 6 COOLANT FITTINGS WERE LEAKING. THE DESIGN FROM PORSCHE HAS THE COOLANT HOSES AFFIXED USING AN EPOXY. AFTER MANY HEAT CYCLES AND TIME, THIS EPOXY FAILS AND COOLANT LEAKS FROM THE ENGINE. THE ENGINE MUST BE REMOVED TO PROPERLY FIX THE PROBLEM AND IT IS GOING TO COST ME APPROXIMATELY $6,000. THIS IS A KNOWN ISSUE FOR THIS CAR AND IS SOMETHING PORSCHE SHOULD TAKE CARE OF. *TR
NHTSA ODI #10597773
45,000 miles · Apr 17, 2014
Engine
ALL CONNECTION PIECES THAT CONNECT TO A RUBBER HOSE ARE LEAKING. THE PIPE THAT COMES OUT OF THE CASTING IS GLUED FROM THE FACTORY. AFTER TIME THE TUBE WILL MOVE AND WATER STARTS COMING OUT IN BETWEEN THE PIPE AND THE CASTING. YOU AN GO TO THIS WEB ADDRESS AND SE WHAT I'M RAKING ABOUT. THIS FROM WHAT I HAVE HEARD AND NOW MY ON C…
Read full complaint
ALL CONNECTION PIECES THAT CONNECT TO A RUBBER HOSE ARE LEAKING. THE PIPE THAT COMES OUT OF THE CASTING IS GLUED FROM THE FACTORY. AFTER TIME THE TUBE WILL MOVE AND WATER STARTS COMING OUT IN BETWEEN THE PIPE AND THE CASTING. YOU AN GO TO THIS WEB ADDRESS AND SE WHAT I'M RAKING ABOUT. THIS FROM WHAT I HAVE HEARD AND NOW MY ON CAR IS SOMETHING THAT HAPPENS TO ALL 2007 PORSCHE TURBO ENGINES. THE PROBLEM IS THAT THE CAR IS OUT OF WARRANTY AND PORSCHE DOESN'T WANT TO FIX IT UNDER WARRANTY. I'M GETTING IT FIXED NOW AND COST IS GOING TO BE OVER $2,000.00 DOLLARS. JUST LIKE THE IMS BEARING FAILURE ON PREVIOUS PORSCHE CARS IT'S GOING TO TAKE AWHILE BEFORE PORSCHE WANTS TO DO ANYTHING TO HELP ANYONE WITH THIS ISSUE. HTTP://WWW.YOUTUBE.COM/WATCH?V=WIL2-VBANVK THE ABOVE WEB-SITE WILL SHOW YOU ONE OF THE ISSUES. IT WILL NOT SHOW YOU THAT ALL PIPES ARE OR WILL COME LOOSE. I REALLY WOULD LIKE TO GET THIS COVERED UNDER WARRANTY. THANKS
NHTSA ODI #10583345
21,000 miles · Feb 16, 2014
Power Train
CAUSE OF PROBLEM IS DUE TO CLUTCH MASTER SLAVE CYLINDER INTERNAL LEAK. PREMATURE FAILURE OF SLAVE CYLINDER. CLUTCH PADDLE WAS DEPRESS AND WILL NOT RETURN FULLY. FEW DAYS LATER, CLUTCH PADDLE WOULD STAY PUT ON THE FLOOR OF THE CAR. CHECK OUT THE BLOG AND IT IS A VERY COMMON PREMATURE FAILURE FOR THIS TYPICAL MODEL HOWEVER, P…
Read full complaint
CAUSE OF PROBLEM IS DUE TO CLUTCH MASTER SLAVE CYLINDER INTERNAL LEAK. PREMATURE FAILURE OF SLAVE CYLINDER. CLUTCH PADDLE WAS DEPRESS AND WILL NOT RETURN FULLY. FEW DAYS LATER, CLUTCH PADDLE WOULD STAY PUT ON THE FLOOR OF THE CAR. CHECK OUT THE BLOG AND IT IS A VERY COMMON PREMATURE FAILURE FOR THIS TYPICAL MODEL HOWEVER, PORSCHE DIDN'T SELL ENOUGH FOR EVERYONE TO GET ON BOARD WITH THE COMPLAINT. *TR
NHTSA ODI #10564565
45,000 miles · Jan 12, 2014
EngineUnknown Or Other
I NOTICED A SMALL POOL OF COOLANT UNDERNEATH THE ENGINE COMPARTMENT. UPON FURTHER RESEARCH I BELIEVE THE CAR IS SUFFERING FROM A COMMON PROBLEM OF THE COOLING FIXTURES THAT ARE GLUED ONTO THE MOTOR RATHER THAN WELDED. AMAZING THAT A CAR THIS EXPENSIVE WOULD HAVE SUCH A POORLY THOUGHT OUT PROBLEM LIKE THIS. I WILL TAKE THE CAR…
Read full complaint
I NOTICED A SMALL POOL OF COOLANT UNDERNEATH THE ENGINE COMPARTMENT. UPON FURTHER RESEARCH I BELIEVE THE CAR IS SUFFERING FROM A COMMON PROBLEM OF THE COOLING FIXTURES THAT ARE GLUED ONTO THE MOTOR RATHER THAN WELDED. AMAZING THAT A CAR THIS EXPENSIVE WOULD HAVE SUCH A POORLY THOUGHT OUT PROBLEM LIKE THIS. I WILL TAKE THE CAR TO THE DEALER FOR ESTIMATES BUT I UNDERSTAND THAT AN ENGINE REMOVAL IS REQUIRED AND ALL COOLANT FIXTURES NEED TO BE WELDED. THIS IS A RATHER EXPENSIVE REPAIR FOR WHAT APPEARS TO BE A VERY FLAWED DESIGN. I HAVE DRIVEN THE CAR ONLY A FEW TIMES SINCE THE FIRST INCIDENT AND NOTICE A POOL OF COOLANT EVERY TIME THE CAR IS PARKED. I WILL NOT DRIVE THE CAR UNTIL FIXED AS I UNDERSTAND THE COOLANT LEAK CAN BE A HAZARD TO BE ME WHILE DRIVING AS WELL AS THE CARS BEHIND ME IF I SUFFER A CATASTROPHIC COOLANT LOSS. *TR
NHTSA ODI #10559491
36,125 miles · Dec 9, 2013
Engine
COOLANT LEAK CAUSED BY FITTING FAILURE. REPAIR REQUIRES ENGINE REMOVAL TO REPLACE PLASTIC FITTINGS. *TR
NHTSA ODI #10555355
48,000 miles · Oct 7, 2013
Engine And Engine Cooling
MY CAR BEGAN LEAKING COOLANT. AFTER TOWING MY CAR TO THE REPAIR SHOP I WAS TOLD MY METAL COOLANT FITTINGS ARE HELD IN WITH EPOXY AND ONE OF THEM HAD FAILED. TO REPAIR THIS IS A $6000.00 JOB. AFTER CALLING THE DEALER I FOUND OUT THIS IS A FAIRLY COMMON PROBLEM BUT THAT PORSCHE IS UNWILLING TO DO ANYTHING TO HELP THE CAR OWNERS P…
Read full complaint
MY CAR BEGAN LEAKING COOLANT. AFTER TOWING MY CAR TO THE REPAIR SHOP I WAS TOLD MY METAL COOLANT FITTINGS ARE HELD IN WITH EPOXY AND ONE OF THEM HAD FAILED. TO REPAIR THIS IS A $6000.00 JOB. AFTER CALLING THE DEALER I FOUND OUT THIS IS A FAIRLY COMMON PROBLEM BUT THAT PORSCHE IS UNWILLING TO DO ANYTHING TO HELP THE CAR OWNERS PAY FOR IT AT THIS TIME. I THINK ANY TIME YOU HAVE A COMMON PROBLEM THAT IS THAT EXPENSIVE TO FIX YOU SHOULD AT HELP A LITTLE WITH THAT PROBLEM. *TR
NHTSA ODI #10547074
18,425 miles · Aug 5, 2013
Engine
DRIVING AT A CONSTANT 50MPH AND HAD A VERY STRONG COOLANT SMELL COME THROUGH THE CABIN. PULLED OVER AND SAW COOLANT SLOWLY DRIPPING UNDER ENGINE. LET CAR COOL DOWN AND DROVE HOME. HAVE NOT DRIVEN CAR SINCE. SCHEDULED A APPOINTMENT WITH DEALER FOR 08/08/13. *TR
NHTSA ODI #10533689
Official recalls
0
No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
2007 Porsche 911 Turbo Problems, Complaints & Recalls | Skip That Year
Illustration