Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 3 of 3 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Engine And Engine Cooling. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Fuel System, Gasoline. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Service Brakes, Hydraulic. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
3 reports
100,044 miles · Sep 12, 2014
Engine And Engine Cooling
I WAS DRIVING MY CAR ON CITY STREETS WHEN A WARNING MESSAGE APPEARED ON MY DASHBOARD INDICATING THAT I SHOULD CHECK MY ENGINE COOLANT LEVEL. I DROVE ON FOR A SHORT TIME (A FEW MINUTES) AND THEN PARKED BRIEFLY, SHUTTING OFF THE ENGINE (AGAIN FOR A FEW MINUTES) TO CONSIDER THE SITUATION AND TO CALL THE SERVICE DEPARTMENT OF MY DE…
Read full complaint
I WAS DRIVING MY CAR ON CITY STREETS WHEN A WARNING MESSAGE APPEARED ON MY DASHBOARD INDICATING THAT I SHOULD CHECK MY ENGINE COOLANT LEVEL. I DROVE ON FOR A SHORT TIME (A FEW MINUTES) AND THEN PARKED BRIEFLY, SHUTTING OFF THE ENGINE (AGAIN FOR A FEW MINUTES) TO CONSIDER THE SITUATION AND TO CALL THE SERVICE DEPARTMENT OF MY DEALERSHIP (WHICH WAS CLOSED SINCE IT WAS LATE IN THE DAY). AS I WAS CLOSE TO HOME, I DECIDED TO DRIVE THE CAR THERE. ABOUT FIVE MINUTES LATER, THE WARNING MESSAGE CHANGED TO AN INDICATION THAT THE ENGINE TEMPERATURE WAS TOO HIGH. I IMMEDIATELY PULLED OVER AND ARRANGED TO TOW THE CAR TO THE DEALERSHIP. THERE THE PROBLEM WAS DIAGNOSED AS A FAILURE OF A COOLANT PIPE THAT LED TO COOLANT LOSS, WHICH REQUIRES AN ESTIMATED $7,500 IN REPAIR WORK. I HAVE SINCE LEARNED THAT THIS IS A RECOGNIZED PROBLEM WITH THE MODEL, MAKE, AND YEAR OF MY CAR. AN NHTSA REPORT HAS BEEN FILED ABOUT THIS, WITH AN ACTION NUMBER OF PE13009 (OPENED ON APRIL 26, 2013). WHILE I WAS NOT DRIVING AT HIGH SPEED AND THERE WAS NO CRASH, FIRE, INJURY, OR FATALITY ASSOCIATED WITH THIS EVENT, THIS ISSUE POSES SIGNIFICANT SAFETY RISKS GIVEN HOW QUICKLY THE VEHICLE'S ENGINE TEMPERATURE EXCEEDED SAFE OPERATING LIMITS. UNDER HIGHER VELOCITY CONDITIONS THE SITUATION COULD HAVE POSED SIGNIFICANT RISKS TO MY AND OTHERS' SAFETY. I HAVE BROUGHT THIS TO YOUR ATTENTION GIVEN THAT IT IS A RECOGNIZED AND ONGOING ISSUE WITH THIS MAKE, MODEL, AND YEAR CAR AND THAT IT APPEARS TO BE CAUSED BY A FUNDAMENTAL DESIGN FLAW. *TR
NHTSA ODI #10632889
58,325 miles · Dec 31, 2013
Engine And Engine CoolingFuel System, GasolineService Brakes, Hydraulic
EPOXY HOLDING PIPE IN WATER PUMP HOUSING FAILED CAUSING PIPE TO SEPARATE, COOLANT TO DUMP ON REAR WHEELS AND BRAKES, AND LOSS OF TRACTION/DEGRADED REAR BRAKING. *TR
NHTSA ODI #10557964
103,000 miles · Jun 28, 2011
Engine And Engine Cooling
PORSCHE 911 TURBO 2005, CATASTROPHIC COOLANT LOSS/FAILURE. CATASTROPHIC COOLANT FAILURE OF A WATER CONNECTION TO THE ENGINE. FAILURE OF ADHESIVE BOND. COOLANT SPRAYED ON REAR TIRES, AND LOSS OF TRACTION. *TR
NHTSA ODI #10409159
Official recalls
0
No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
2005 Porsche 911 Turbo S Problems, Complaints & Recalls | Skip That Year
Illustration