← New search

2010 Pontiac Vibe

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2010 Pontiac Vibe do not stand out strongly from the model-year median of 116.5.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all Vibe years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

28 reports with mileage · 30 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 31 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Vehicle Speed Control. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 4 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

5 crash reports0 fire reports4 injury reports

Steering complaints

4 reports
Clear category filter
Mileage unknown · Aug 16, 2019
Steering

THE STEERING WHEEL RATTLES BADLY. THIS HAPPENS WHEN DRIVING AND ALSO WHEN MOVING THE STEERING WHEEL SIDE TO SIDE WHILE STATIONARY. ALSO SHUDDERS WHEN BRAKING.

NHTSA ODI #11244493

118,000 miles · Jul 25, 2017
Steering

THERE IS A PERSISTENT RATTLE COMING FROM DIRECTLY BEHIND THE STEERING WHEEL. ESPECIALLY NOTICEABLE AT SPEEDS <35 MPH AND/OR DRIVING OVER BUMPY PAVEMENT. WHEN THE RATTLE IS OCCURRING, THE STEERING COLUMN FEELS LIKE IT OSCILLATING VERY QUICKLY.

NHTSA ODI #11010467

23,000 miles · Jun 6, 2011
Service Brakes, HydraulicSteeringCrashInjury

TL*THE CONTACT OWNS A 2010 PONTIAC VIBE. WHILE DRIVING APPROXIMATELY 40 MPH AND ACCELERATING AROUND A CURB THE VEHICLE JERKED TO THE RIGHT VIOLENTLY. THE CONTACT WAS ABLE TO CONTROL THE VEHICLE, IT WAS TAKEN TO THE DEALER WHERE THE TECHNICIANS WERE UNABLE TO DUPLICATE OR DIAGNOSE THE FAILURE. THE CONTACT STATED THE FAILURE OCCU…

Read full complaint

TL*THE CONTACT OWNS A 2010 PONTIAC VIBE. WHILE DRIVING APPROXIMATELY 40 MPH AND ACCELERATING AROUND A CURB THE VEHICLE JERKED TO THE RIGHT VIOLENTLY. THE CONTACT WAS ABLE TO CONTROL THE VEHICLE, IT WAS TAKEN TO THE DEALER WHERE THE TECHNICIANS WERE UNABLE TO DUPLICATE OR DIAGNOSE THE FAILURE. THE CONTACT STATED THE FAILURE OCCURRED A SECOND TIME WHILE DRIVING APPROXIMATELY 70 MPH ON THE HIGHWAY. THE ANTI LOCK BRAKES LOCKED AND THE VEHICLE WOULD SLIDE WHILE THE BRAKES WERE APPLIED. THE CONTACT STATED THE VEHICLE FLIPPED OVER WHILE DRIVING DOWN A HILL. THE AIR BAGS DID NOT DEPLOY. THE CONTACT AND THE PASSENGER SUSTAINED BUMPS, BRUISES, AND SCRATCHES AND WERE TRANSPORTED TO THE HOSPITAL BY AMBULANCE WHERE THEY WERE RELEASED WITH NO MAJOR INJURIES. A POLICE REPORT WAS FILED. THE CONTACT STATED THERE WERE VISIBLE SKID MARKS ON THE ROAD WHERE THE VEHICLE WAS SLIDING. THE VEHICLE WAS TOWED TO A AN IMPOUND TOW LOT. THE CONTACT ALSO STATED PRIOR TO THE CRASH WHILE DEPRESSING THE BRAKE PEDAL HE HAD EXPERIENCED THE STEERING WHEEL TURNING AND LOCKING AT HIGH SPEEDS AND WHILE THE BRAKE PEDAL WAS DEPRESSED. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 23,000.

NHTSA ODI #10404573

4,500 miles · Feb 14, 2010
Steering

AT HIGHWAY SPEEDS, MY CAR WILL SUDDENLY STEER SHARPLY ON ITS OWN, AS IF IT WERE HIT BY A SUDDEN, VIOLENT CROSSWIND THIS HAS HAPPENED APPROXIMATELY 20-25 TIMES, ALWAYS AT HIGHWAY SPEEDS. ALWAYS SWERVING TO THE LEFT. NO ACCIDENTS HAVE OCCURRED, BUT EACH OCCURRENCE COULD HAVE RESULTED IN AN ACCIDENT, AS IT IS DIFFICULT, IF NOT I…

Read full complaint

AT HIGHWAY SPEEDS, MY CAR WILL SUDDENLY STEER SHARPLY ON ITS OWN, AS IF IT WERE HIT BY A SUDDEN, VIOLENT CROSSWIND THIS HAS HAPPENED APPROXIMATELY 20-25 TIMES, ALWAYS AT HIGHWAY SPEEDS. ALWAYS SWERVING TO THE LEFT. NO ACCIDENTS HAVE OCCURRED, BUT EACH OCCURRENCE COULD HAVE RESULTED IN AN ACCIDENT, AS IT IS DIFFICULT, IF NOT IMPOSSIBLE TO MAINTAIN LANE DISCIPLINE. VEHICLE IS 6 MONTHS OLD, 5,000 MILES. NO KNOWN DAMAGE OR UNUSUAL WEAR THAT WOULD CAUSE SUCH A REACTION. *TR

NHTSA ODI #10310267

Official recalls

8

18V024000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2013 Scion xB, Toyota Corolla, Corolla Matrix, Sienna, 4Runner, Lexus IS250, IS350, IS250C, IS350C, IS-F, and GX460 vehicles sold, ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP (Saipan), and the U.S. VI or "Zone A." Toyota is also recalling certain 2010 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, 4Runner, Lexus IS250, IS350, IS250C, IS350C, ES350, IS-F, GX460, and Pontiac Vibe vehicles sold, ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Toyota is also recalling certain 2009 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, Lexus IS250, IS350, ES350, IS-F, and Pontiac Vibe vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the vehicle model, dealers will replace the front passenger air bag inflator, or replace the air bag assembly. The recall began on January 29, 2018. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for this recall are "Zone A" Toyota: G0P, Lexus: GLG; "Zone B" Toyota: G0R, Lexus GLH; "Zone C" Toyota: H0A, and Lexus: HLA.

18V025000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

On January 9, 2018, Toyota Motor Engineering & Manufacturing (Toyota) notified NHTSA that they are recalling 14,585 model year 2010-2012 Yaris vehicles ever registered in the states of Alaska, Arizona, Arkansas, Colorado, Connecticut, Delaware, District of Columbia, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, Montana, Nebraska, Nevada, New Hampshire, New Jersey, New Mexico, New York, North Carolina, North Dakota, Ohio, Oklahoma, Oregon, Pennsylvania, Rhode Island, South Dakota, Tennessee, Utah, Vermont, Virginia, Washington, West Virginia, Wisconsin, and Wyoming. As of January 30, 2018, Toyota is additionally recalling 3,347 model year 2010 Pontiac Vibe vehicles located in states listed above. Also included in this recall filing is 98,194 model year 2003-2008 Toyota Corolla Matrix vehicles, located throughout the U.S., that previously received a “like-for-like” interim air bag inflator replacement. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners, and dealers will replace the passenger frontal air bag assemblies with an alternate inflator, free of charge. The recall began on January 29, 2018. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0R (Zone B), and H0A (Zone C), J0A (Matrix Zone A), J0A (Matrix Zone A), J0A (Matrix Zone A).

16V340000 · Air Bags:frontal:passenger Side:inflator Module

May 23, 2016

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2011 Scion xB and Lexus IS F, 2009-2011 Toyota Corolla and Corolla Matrix, 2006-2011 Toyota Yaris, Lexus IS250 and Lexus IS350, 2010-2011 Toyota 4Runner, Lexus IS250C, Lexus IS350C and Lexus GX460, 2011 Sienna, 2007-2011 Lexus ES350, and 2009-2010 Pontiac Vibe vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain model year 2008 Scion xB and Lexus IS F, 2007-2008 Toyota Yaris, 2006-2008 Lexus IS250 and Lexus IS350 and 2007-2008 Lexus ES350 vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on December 6, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for interim notification for this campaign are G1P (Toyota Zone A), G1R (Toyota Zone B), G2G (Lexus Zone A), and G2H (Lexus Zone B). Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), GLG (Lexus Zone A), and GLH (Lexus Zone B).

15V689000 · Visibility:power Window Devices And Controls

Oct 22, 2015

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Consequence & remedy

Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.

14V168000 · Air Bags:frontal:driver Side:inflator Module

Apr 9, 2014

Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.

Consequence & remedy

Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.

Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.

10V024000 · Vehicle Speed Control:accelerator Pedal

Jan 27, 2010

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 PONTIAC VIBE PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.

Consequence & remedy

Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.

Remedy: GENERAL MOTORS WILL NOTIFY CUSTOMERS WHEN A RECALL REMEDY IS AVAILABLE FOR RECALL 10038: FLOOR MAT INTERFERENCE AND ACCELERATOR PEDAL. GM REQUESTS THAT CUSTOMERS TAKE OUT ANY REMOVABLE (CARPETED, ALL-WEATHER, OR OTHER) DRIVER'S FLOOR MAT AND NOT REPLACE IT WITH ANY OTHER FLOOR MAT, AND PLACE IT IN THE TRUNK UNTIL THE FLOOR MAT INTERFERENCE AND ACCELERATOR PEDAL RECALL REMEDY IS READY AND IMPLEMENTED. IN THE EVENT THAT OWNERS CHOOSE NOT TO TAKE OUT THEIR REMOVABLE FLOOR MAT, GENERAL MOTORS STRONGLY RECOMMENDS THAT OWNERS USE ONLY FLOOR MATS DESIGNED SPECIFICALLY FOR THE MODEL AND MODEL YEAR OF THEIR VEHICLE, AND THAT IT IS PROPERLY INSTALLED AND SECURED. DO NOT USE A MAT THAT IS FLIPPED OVER WITH THE BOTTOM-SIDE UP, AND DO NOT STACK ONE FLOOR MAT OVER ANOTHER. IN ADDITION, CHECK THE OPERATION OF THE ACCELERATOR, BRAKE, AND CLUTCH (IF APPLICABLE) PEDALS TO ASSURE THAT THE FLOOR MAT DOES NOT INTERFERE WITH THEM. OWNERS MAY CONTACT PONTIAC AT 1-800-620-7668 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.

10V018000 · Vehicle Speed Control:accelerator Pedal

Jan 21, 2010

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 PONTIAC VIBE VEHICLES. DUE TO THE MANNER IN WHICH THE FRICTION LEVER INTERACTS WITH THE SLIDING SURFACE OF THE ACCELERATOR PEDAL INSIDE THE PEDAL SENSOR ASSEMBLY, THE SLIDING SURFACE OF THE LEVER MAY BECOME SMOOTH DURING VEHICLE OPERATION. IN THIS CONDITION, IF CONDENSATION OCCURS ON THE SURFACE, AS MAY OCCUR FROM HEATER OPERATION (WITHOUT A/C) WHEN THE PEDAL ASSEMBLY IS COLD, THE FRICTION WHEN THE ACCELERATOR PEDAL IS OPERATED MAY INCREASE, WHICH MAY RESULT IN THE ACCELERATOR PEDAL BECOMING HARDER TO DEPRESS, SLOWER TO RETURN, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION.

Consequence & remedy

Consequence: THE ACCELERATOR PEDAL MAY BECOME HARD TO DEPRESS, SLOW TO RETURN TO IDLE, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSTALL A REINFORCEMENT BAR IN THE ACCELERATOR PEDAL WHICH WILL ALLOW THE PEDAL TO OPERATE SMOOTHLY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN EARLY FEBRUARY AND BE COMPLETED IN LATE APRIL 2010. OWNERS MAY CONTACT PONTIAC AT 1-800-620-7668 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.

09V392000 · Service Brakes, Hydraulic:power Assist:vacuum

Aug 31, 2009

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2009-2010 PONTIAC VIBE VEHICLES EQUIPPED WITH 1.8L ENGINE AND ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF ALASKA, COLORADO, IDAHO, ILLINOIS, IOWA, KANSAS, MAINE, MICHIGAN, MINNESOTA, MONTANA, NEBRASKA, NEVADA, NEW HAMPSHIRE, NEW YORK, NORTH DAKOTA, SOUTH DAKOTA, VERMONT, WISCONSIN, AND WYOMING. WHEN DRIVING UNDER CERTAIN UNIQUE CONDITIONS IN EXTREMELY LOW AMBIENT TEMPERATURES, THE INTAKE MANIFOLD SUCTION PORT FOR THE BRAKE VACUUM CAN BECOME LOCKED DUE TO THE FREEZING OF CONDENSATION RESULTING FROM POSITIVE CRANKCASE VENTILATION.

Consequence & remedy

Consequence: THIS COULD LEAD TO AN INCREASE IN VEHICLE STOPPING DISTANCE AND A CRASH COULD OCCUR.

Remedy: DEALERS WILL MODIFY THE BRAKE VACUUM LINE FREE OF CHARGE. A SPECIAL ADVISORY LETTER WILL BE SENT TO OWNERS OF VEHICLES REGISTERED IN ALL OTHER STATES IN THE SAME TIME FRAME. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE OCTOBER 23, 2009. OWNERS MAY CONTACT PONTIAC AT 1-800-620-7668 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

AQ10001 · Fleet Vehicle Recall Completion Audit

Opened Nov 18, 2010 · Closed Dec 28, 2015

Status: closed (inferred from source dates) · Unknown Or Other

On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.