WHILE ATTEMPTING TO BACK OUT OF MY GARAGE, THE COIL SPRING ON THE FRONT DRIVER SIDE STRUT BROKE AND SHOT INTO MY FRONT TIRE, PUNCTURING AND IMMEDIATELY FLATTENING MY TIRE. THE SPRING WAS EMBEDDED IN THE TIRE SO FAR THAT THEY WERE UNABLE TO REMOVE THE TIRE TO PUT ON THE SPARE. THE CAR HAD TO BE FORCED IN REVERSE FAR ENOUGH BACK…
Read full complaint
WHILE ATTEMPTING TO BACK OUT OF MY GARAGE, THE COIL SPRING ON THE FRONT DRIVER SIDE STRUT BROKE AND SHOT INTO MY FRONT TIRE, PUNCTURING AND IMMEDIATELY FLATTENING MY TIRE. THE SPRING WAS EMBEDDED IN THE TIRE SO FAR THAT THEY WERE UNABLE TO REMOVE THE TIRE TO PUT ON THE SPARE. THE CAR HAD TO BE FORCED IN REVERSE FAR ENOUGH BACK TO BE ABLE TO HOOK IT ONTO THE TOW TRUCK WHICH SHREDDED THE FRONT TIRE. HAD TO HAVE FRONT SPRINGS, STRUTS, ABS SPEED SENSOR, ALIGNMENT AND NEW TIRE PUT ON THE VEHICLE. VERY LUCKY THAT THIS INCIDENT HAPPENED IN MY GARAGE AND NOT OUT ON THE ROADWAY. *TR
NHTSA ODI #10378681
94,000 miles · Jan 17, 2011
Suspension
AROUND 7 MONTHS AGO JULY,2010 MY WIFE WAS ATTEMPTING TO BACK UP HER 2002 MERCURY SABLE AND THE PASSENGER SIDE FRONT SPRING BROKE AN WENT TROUGH THE SIDE WALL OF THE TIRE. TODAY JAN. 2011. I WAS ATTEMPTING TO BACK THAT SAME CAR AN THE DRIVER SIDE SPRING BROKE AND RUINED THE TIRE AN BUSTED ANOTHER PART ON THE STEERING LINK. WHEN I…
Read full complaint
AROUND 7 MONTHS AGO JULY,2010 MY WIFE WAS ATTEMPTING TO BACK UP HER 2002 MERCURY SABLE AND THE PASSENGER SIDE FRONT SPRING BROKE AN WENT TROUGH THE SIDE WALL OF THE TIRE. TODAY JAN. 2011. I WAS ATTEMPTING TO BACK THAT SAME CAR AN THE DRIVER SIDE SPRING BROKE AND RUINED THE TIRE AN BUSTED ANOTHER PART ON THE STEERING LINK. WHEN IS SOMETHING GOING TO BE DONE ABOUT THIS. *TR
NHTSA ODI #10376982
66,000 miles · Jan 10, 2011
Suspension
TL* THE CONTACT OWNS A 2002 MERCURY SABLE. THE CONTACT STATED THAT THE VEHICLE WAS PARKED WHEN THERE WAS A LOUD BOOM. THE CONTACT DISCOVERED THAT THE COIL SPRING WAS FRACTURED AND PUNCTURED A HOLE IN THE TIRE SIMILAR TO THE FAILURE DESCRIBED IN NHTSA CAMPAIGN ID NUMBER: 04V332000 ( SUSPENSION: FRONT: SPRINGS: COIL SPRINGS). BOTH…
Read full complaint
TL* THE CONTACT OWNS A 2002 MERCURY SABLE. THE CONTACT STATED THAT THE VEHICLE WAS PARKED WHEN THERE WAS A LOUD BOOM. THE CONTACT DISCOVERED THAT THE COIL SPRING WAS FRACTURED AND PUNCTURED A HOLE IN THE TIRE SIMILAR TO THE FAILURE DESCRIBED IN NHTSA CAMPAIGN ID NUMBER: 04V332000 ( SUSPENSION: FRONT: SPRINGS: COIL SPRINGS). BOTH THE DEALER AND MANUFACTURER WERE NOTIFIED OF THE FAILURE WHO THEN INFORMED THE CONTACT THAT HIS VEHICLE WAS NOT INCLUDED IN THE RECALL AND THAT COULD NOT OFFER ANY ADDITIONAL ASSISTANCE. THE REPAIR SHOP REPAIRED ALL FOUR COIL SPRINGS AND STRUTS INCLUDING PREVENTATIVE MAINTENANCE AT THE CONTACTS EXPENSE. THE CURRENT AND FAILURE MILEAGE WAS APPROXIMATELY 66,000. UPDATED 2/28/11 *CN UPDATED 05/26/11
NHTSA ODI #10375455
62,000 miles · Jan 5, 2011
Suspension
TL - THE CONTACT OWNS 2002 MERCURY SABLE. THE CONTACT STATED THAT WHILE LEAVING A PARKING SPACE THE SPRING COIL BROKE AND PUNCTURED THE TIRE. THE VEHICLE WAS TOWED INTO A LOCAL SHOP AND ITS BEING REPAIRED. THE FAILURE AND CURRENT MILEAGE IS 62,000. PM
NHTSA ODI #10374761
112,409 miles · Jan 4, 2011
Suspension
TL*THE CONTACT OWNS A 2002 MERCURY SABLE GS . WHILE DRIVING APPROXIMATELY 35 MPH, THERE WAS A LOUD NOISE FROM UNDER THE VEHICLE AND IT PULLED TO THE LEFT. ALSO THERE WAS A BURNING RUBBER ODOR. THE CONTACT WAS ABLE TO DRIVE THE VEHICLE HOME. AFTER INSPECTING THE VEHICLE, THE CONTACT NOTICED THAT THE FRONT COIL SPRING ON THE DRIV…
Read full complaint
TL*THE CONTACT OWNS A 2002 MERCURY SABLE GS . WHILE DRIVING APPROXIMATELY 35 MPH, THERE WAS A LOUD NOISE FROM UNDER THE VEHICLE AND IT PULLED TO THE LEFT. ALSO THERE WAS A BURNING RUBBER ODOR. THE CONTACT WAS ABLE TO DRIVE THE VEHICLE HOME. AFTER INSPECTING THE VEHICLE, THE CONTACT NOTICED THAT THE FRONT COIL SPRING ON THE DRIVER SIDE WAS BROKEN. THE CONTACT STATED THERE WAS AN OPEN INVESTIGATION FOR THAT FAILURE (NHTSA ACTION NUMBER: EA08018). THE MANUFACTURER WAS CONTACTED AND STATED THEY COULD NOT PROVIDE ASSISTANCE AND THE CONTACT WOULD HAVE TO REPAIR THE VEHICLE AT HIS OWN EXPENSE AND SAVE RECEIPTS IF IN THE FUTURE THERE WAS RECALL. THE VEHICLE WAS REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 112,409. UPDATED 03/29/11 *BF THE CONSUMER STATED THE STRUTS, BEARING PLATES AND LEFT LOWER BALL JOINTS HAD TO BE REPLACED. UPDATED 08/22/11
NHTSA ODI #10374071
50,000 miles · Jan 3, 2011
Suspension
TL* THE CONTACT OWNS A 2002 MERCURY SABLE. THE CONTACT WAS DRIVING APPROXIMATELY 15 MPH ATTEMPTING A TURN WHEN SUDDENLY THERE WAS A LOUD NOISE COMING FROM OUTSIDE OF THE VEHICLE. THE CONTACT PULLED OVER TO THE SIDE OF THE ROAD AND NOTICED THAT THE REAR OF THE VEHICLE SLIGHTLY COLLAPSED IN A TILED POSITION TOWARDS THE PASSENGER S…
Read full complaint
TL* THE CONTACT OWNS A 2002 MERCURY SABLE. THE CONTACT WAS DRIVING APPROXIMATELY 15 MPH ATTEMPTING A TURN WHEN SUDDENLY THERE WAS A LOUD NOISE COMING FROM OUTSIDE OF THE VEHICLE. THE CONTACT PULLED OVER TO THE SIDE OF THE ROAD AND NOTICED THAT THE REAR OF THE VEHICLE SLIGHTLY COLLAPSED IN A TILED POSITION TOWARDS THE PASSENGER SIDE. THE VEHICLE WAS DRIVEN AT AN EXTREMELY LOW SPEED RATE TO THE NEAREST DEALER FOR DIAGNOSIS. THE REAR PASSENGER SIDE COIL SPRING FRACTURED, AND WAS REPLACED. MOST RECENTLY, THE CONTACT STATED THAT THE FRONT DRIVER SIDE COIL SPRING COMPLETELY FRACTURED AND CAUSED THE TIRE TO EXPLODE. THE VEHICLE WAS IN THE PROCESS OF BEING REPAIRED BY AN INDEPENDENT MECHANIC. THE FAILURE MILEAGE WAS APPROXIMATELY 50,000. UPDATED 3/14/11 *CN UPDATED 12/14/11 *CN
NHTSA ODI #10373944
110,000 miles · Jan 3, 2011
Suspension
I AM WRITING THE NHTSA IN ORDER TO WARN OF A DANGEROUS, POTENTIALLY FATAL, HAZARDOUS CONDITION ON A MERCURY AUTOMOBILE. TO THE BEST OF MY KNOWLEDGE THIS CONDITION HAS BEEN ADDRESSED BY A PREVIOUS RECALL NOTICE ON EARLIER YEAR MODELS OF THE MERCURY SABLE BUT NOT ON THE YEAR MODEL THAT I OWN. I OWN A 2002 MERCURY SABLE. IN FEBRUAR…
Read full complaint
I AM WRITING THE NHTSA IN ORDER TO WARN OF A DANGEROUS, POTENTIALLY FATAL, HAZARDOUS CONDITION ON A MERCURY AUTOMOBILE. TO THE BEST OF MY KNOWLEDGE THIS CONDITION HAS BEEN ADDRESSED BY A PREVIOUS RECALL NOTICE ON EARLIER YEAR MODELS OF THE MERCURY SABLE BUT NOT ON THE YEAR MODEL THAT I OWN. I OWN A 2002 MERCURY SABLE. IN FEBRUARY OF 2010 I HAD A FLAT TIRE ON MY DRIVER'S REAR SIDE WHEN PULLING OUT OF A PARKING LOT. WHEN I REMOVED THE TIRE I FOUND THAT A SPRING HAD BROKEN AND PUNCTURED THE SIDE OF THE TIRE AND HAD CUT THE TIRE IN A CIRCULAR MOTION CAUSING A RAPID EXPULSION OF AIR. ON JANUARY 1 OF 2011 THE DRIVER'S SIDE FRONT TIRE FLATTENED WHILE PULLING OUT OF A PARKING LOT. THE SAME THING HAD HAPPENED AGAIN. THE SPRING HAD BROKEN AND PUNCTURED THE SIDE OF THE TIRE. AFTER THE SECOND OCCURRENCE I SEARCHED THE INTERNET FOR INFORMATION TO SEE IF OTHERS HAVE HAD SIMILAR EXPERIENCES AND FOUND NHTSA CAMPAIGN ID NUMBER 04V332000. CAMPAIGN ID NUMBER 04V332000 EXACTLY DESCRIBES THE CONDITIONS THAT I HAVE ON MY VEHICLE. HOWEVER, MY VEHICLE IS A 2002 MERCURY SABLE AND THE RECALL COVERS 1999-2001 AND DOES NOT ADDRESS THE REAR SPRINGS. WERE THESE TO OCCUR AT HIGHWAY SPEEDS THIS MAY HAVE CAUSED SERIOUS INJURIES OR FATALITIES. THIS CONDITION HAS THE POTENTIAL TO CAUSE LOSS OF CONTROL TO THE VEHICLE AND NEEDS TO BE ADDRESSED BY FORD MOTOR COMPANY IMMEDIATELY IN ORDER TO WARN THE PUBLIC OF THIS DANGEROUS CONDITION. EXPANSION OF THE RECALL SHOULD INCLUDE THE LATER YEAR MODELS AND THE REAR SPRINGS OF ALL VEHICLES THAT UTILIZE THESE SPRINGS AND ENGINEERING DESIGN. I PURCHASED THIS VEHICLE USED AT A FORD/MERCURY DEALERSHIP AND HAVE NEVER RECEIVED A NOTICE, RECALL OR OTHERWISE, CONCERNING THIS CONDITION. *TR
NHTSA ODI #10373832
80,000 miles · Dec 27, 2010
Suspension
2002 MERCURY SABLE-LEFT FRONT COIL SPRING FAILED AND DESTROYED THE RADIAL TIRE AT THAT LOCATION. CAR HAS APPROXIMATELY 80,000 MILES HAS BEEN CAREFULLY MAINTAINED. FORD MOTOR CO. SAYS IT IS NOT COVERED UNDER ANY RECALL. CAR IS AT THE SHOP FOR REPAIRS WHICH INCLUDE REPLACING BOTH COIL SPRINGS AND REPLACING DAMAGED TIRE. ANY OTHER …
Read full complaint
2002 MERCURY SABLE-LEFT FRONT COIL SPRING FAILED AND DESTROYED THE RADIAL TIRE AT THAT LOCATION. CAR HAS APPROXIMATELY 80,000 MILES HAS BEEN CAREFULLY MAINTAINED. FORD MOTOR CO. SAYS IT IS NOT COVERED UNDER ANY RECALL. CAR IS AT THE SHOP FOR REPAIRS WHICH INCLUDE REPLACING BOTH COIL SPRINGS AND REPLACING DAMAGED TIRE. ANY OTHER DAMAGE FROM THIS EVENT IS YET TO BE DETERMINED. THIS EVENT TOOK PLACE DECEMBER 27, 2010 @ APPROX. 01:00 P.M. *TR
NHTSA ODI #10372560
88,800 miles · Dec 27, 2010
Suspension
FRONT COIL SPRING OF MY 2002 MERCURY SABLE BROKE AND PUNCTURED A HOLE IN THE TIRE. HAD TO REPLACE COIL SPRING, STRUT, AND SWAY BAR LINKS. *TR
NHTSA ODI #10372492
92,082 miles · Dec 24, 2010
Suspension
2002 SABLE. LEFT FRONT COIL SPRING BROKE AND PUNCTURED THE TIRE WHEN BACKING OUT OF THE GARAGE. I HAD THE LOCAL FORD GARAGE REPLACE BOTH FRONT SPRINGS AND INSTALL THE PROTECTIVE GUARD KIT (USED ON THE RE-CALLED VEHICLES) TO PREVENT TIRE PUNCTURE IF IT HAPPENS AGAIN. THIS CAR WAS NOT RE-CALLED AND FORD DID NOT COVER THE COST; $40…
Read full complaint
2002 SABLE. LEFT FRONT COIL SPRING BROKE AND PUNCTURED THE TIRE WHEN BACKING OUT OF THE GARAGE. I HAD THE LOCAL FORD GARAGE REPLACE BOTH FRONT SPRINGS AND INSTALL THE PROTECTIVE GUARD KIT (USED ON THE RE-CALLED VEHICLES) TO PREVENT TIRE PUNCTURE IF IT HAPPENS AGAIN. THIS CAR WAS NOT RE-CALLED AND FORD DID NOT COVER THE COST; $400 NOT INCLUDING THE TIRE. *TR
CERTAIN PASSENGER VEHICLES ARE BEING RECALLED TO CORRECT A PROBLEM WITH A MALFUNCTIONING STOP LAMP SWITCH AND/OR ASSOCIATED WIRING. THIS MALFUNCTIONING COULD RENDER THE STOP LAMPS INOPERABLE OR CAUSE THEM TO STAY ON ALL THE TIME. THIS COULD CAUSE CONFUSION TO A FOLLOWING DRIVER, WHICH COULD LEAD TO A CRASH.
Consequence & remedy
Consequence: IN ADDITION, IF THE SWITCH AND/OR ASSOCIATED WIRING FAIL IN THE OPEN POSITION, THE BRAKE LIGHTS WILL NOT ACTUATE AND THE DRIVER WILL NOT BE ABLE TO SHIFT THE VEHICLE OUT OF "PARK" IF THEY FAIL IN THE CLOSED POSITION, THE BRAKE LIGHTS WILL REMAIN ON, WHICH WILL NOT ALLOW THE SPEED CONTROL TO BE ACTIVATED. THIS COULD ALSO CAUSE THE BATTERY TO DISCHARGE.
Remedy: DEALERS WILL REMOVE THE STOP LAMP SWITCH AND ASSOCIATED WIRING ASSEMBLY AND INSTALL A NEWLY DESIGNED STOP LAMP SWITCH AND WIRE ASSEMBLY. OWNER NOTIFICATION IS EXPECTED TO BEGIN ON APRIL 5, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING." THE WINDSHIELDS MAY POTENTIALLY EXHIBIT INCREASED WIND NOISE, WATER LEAKAGE, AND SQUEAKS AND RATTLES.
Consequence & remedy
Consequence: POTENTIAL LOSS OF WINDSHIELD RETENTION MAY ALSO REDUCE OCCUPANT PROTECTION IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL REPLACE THESE WINDSHIELDS. OWNER NOTIFICATION BEGAN ON MARCH 31, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD/MERCURY AT 1-800-392-3673.
CERTAIN PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PADELS ARE BEING RECALLED IN ORDER TO ADJUST THE BRAKE AND ACCELERATOR PEDALS TO A MINIMUM OF 50 MM OF LATERAL SEPARATION. SIMULTANEOUS APPLICATION OF BOTH THE BRAKE AND ACCELERATOR PEDALS COULD RESULT IN AN INCREASE IN ENGINE RPM.
Consequence & remedy
Consequence: THIS COULD RESULT IN A CUSTOMER EXPERIENCING AN "UNINTENDED VEHICLE SPEED INCREASE" OR A PERCEIVED "UNABLE TO STOP" CONDITION.
Remedy: OWNERS WILL BE INSTRUCTED AS TO THE PROPER WAY TO SET THE POSITION OF THE PEDALS AND TO TAKE THEIR VEHICLES TO A DEALER TO HAVE THE SPACING BETWEEN THE BRAKE AND ACCELERATOR PEDALS MEASURED. IF THE SPACING IS FOUND TO BE LESS THAN 50 MM, THE DEALER WILL ADJUST THE PEDALS TO INCREASE THE DISTANCE BETWEEN THEM TO GREATER THAN 50 MM. OWNER NOTIFICATION BEGAN OCTOBER 28, 2002. OWNERS WHO DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4
PE12033 · Speed Control Cable Damage
Opened Oct 24, 2012 · Closed Jun 26, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:cables; Vehicle Speed Control:cruise Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Additional source detail variants (3)
Vehicle Speed Control:cables
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Vehicle Speed Control:cruise Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
Vehicle Speed Control
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
EA08018 · Front Suspension Coil Spring Fracture
Opened Aug 28, 2008 · Closed Jun 30, 2011
Status: closed (inferred from source dates) · Suspension:front:springs:coil Springs
To date, ODI is aware of 2,401 non-duplicative complaints related to the alleged defect. In addition, ODI is aware of 1,411 subject vehicles with one or more warranty claims related to the alleged defect. In total, ODI is aware of 3,645 unique subject vehicles that have experienced one or more front suspension coil spring fractures. ODI is also aware of four minor crashes related to the alleged defect resulting in one minor injury.With greater than eight years of exposure, a large subject vehicle population and approximately 2,052 reported front tire punctures caused by fractured coil springs (at all speeds), there have been no reported severe crashes, deaths or injuries related to the alleged defect. The real world consequences of these defective coil springs have been a small number of minor control problems that resulted in minor damage; suggesting that the effect of the defect on vehicle control is minor.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted. Accordingly, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency will continue to monitor this issue and will take further action if warranted by the circumstances. See the EA08-018 Engineering Analysis Closing Report for more details.
RP03001 · Brake/accelerator Pedal Application
Opened Oct 31, 2003 · Closed Mar 23, 2004
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:pedals And Linkages
MS. RODMAN REPORTED THAT AFTER HER VEHICLE WAS INSPECTED FOR THE RECALL, HER MOTHER EXPERIENCED A SUDDEN ACCELERATION AND CRASHED THE SABLE INTO A LIGHT POLE.PREVIOUSLY NHTSA HAD CONDUCTED AN INVESTIGATION FOR THIS ISSUE (PE02-035) THAT RESULTED IN THE RECALL (02V-266) OF 369,000 MY 2000-2002 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE BRAKE AND ACCELERATOR PEDALS TO INSURE THAT THE SEPARATION BETWEEN THE PEDALS WAS AT LEAST 50MM..A REVIEW OF ODI'S DATABASE FOR COMPLAINTS REGARDING RECALL 02V-266 DID NOT IDENTIFY ANY RECALL REMEDY COMPLAINTS OTHER THAN THE PETITIONER'S.MS. RODMAN?S VEHICLE WAS INSPECTED BY ODI USING FORD?S SPECIAL TOOL AND HER VEHICLE WAS FOUND TO EXCEED 50MM.ALSO, THE LATERAL MOVEMENT OF THE PEDALS WAS FOUND NOT TO BE EXCESSIVE RELATIVE TO OTHER COMPARABLE TAURUS AND SABLE VEHICLES.THEREFORE, IT IS UNLIKELY THAT NHTSA WOULD ISSUE AN ORDER REQUIRING FORD TO PROVIDE A DIFFERENT REMEDY FOR THIS DEFECT.IN VIEW OF THE NEED TO ALLOCATE AND PRIORITIZE NHTSA?S LIMITED RESOURCES TO BEST ACCOMPLISH THE AGENCY?S SAFETY MISSION, THE PETITION IS DENIED.FOR ADDITIONAL INFORMATION CONCERNING THIS ANALYSIS, PLEASE REFER TO THE FEDERAL REGISTER NOTICE DATED MARCH 23, 2004 (VOL 69, NO 56, PAGES 13619-13620).
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Additional source detail variants (5)
Exterior Lighting:brake Lights
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:brake Lights:switch
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:tail Lights
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
Exterior Lighting:tail Lights:switch
FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.
2002 Mercury Sable Problems, Complaints & Recalls | Skip That Year
Illustration