NHTSA owner reports · September 18, 2026 snapshot.
Steering complaints
14 reportsClear category filter199,205 miles · Mar 13, 2017
SteeringVehicle Speed Control
MY VEHICLE WAS UNDER RECALL AND WAS SERVICED ON FEB 9TH 2015 FOR BRAKE SWITCH DEALING WITH CRUISE CONTROL AND POWER STEERING LOW PRESSURE HOSE ON 3/11/2017 THE SAME PROBELMS OCCURED AND IT IS A MANUFACTOR ISSUE AND NOT GETTING JUSTICE FOR GETTING MY VEHICLE REPAIRED FOR SAME ISSUE VEHICLE AS I WAS DRIVING CAR IT WAS FIXED BY MER…
Read full complaint
MY VEHICLE WAS UNDER RECALL AND WAS SERVICED ON FEB 9TH 2015 FOR BRAKE SWITCH DEALING WITH CRUISE CONTROL AND POWER STEERING LOW PRESSURE HOSE ON 3/11/2017 THE SAME PROBELMS OCCURED AND IT IS A MANUFACTOR ISSUE AND NOT GETTING JUSTICE FOR GETTING MY VEHICLE REPAIRED FOR SAME ISSUE VEHICLE AS I WAS DRIVING CAR IT WAS FIXED BY MERCEDES-BENZ OF WAPPINGERS FALLS ON FEB 9TH 2015 BUT SAME ISSUE RETURNED.
NHTSA ODI #10965771
174,000 miles · Dec 15, 2014
Steering
TL* THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE CONTACT STATED THAT WHILE DRIVING AT AN UNKNOWN SPEED, THE STEERING WHEEL BECAME DIFFICULT TO TURN AND THE ESP FAULT WARNING LIGHT ILLUMINATED. IN ADDITION, WHEN THE STEERING WHEEL WAS TURNED, AN ABNORMAL NOISE EMITTED FROM THE VEHICLE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRE…
Read full complaint
TL* THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE CONTACT STATED THAT WHILE DRIVING AT AN UNKNOWN SPEED, THE STEERING WHEEL BECAME DIFFICULT TO TURN AND THE ESP FAULT WARNING LIGHT ILLUMINATED. IN ADDITION, WHEN THE STEERING WHEEL WAS TURNED, AN ABNORMAL NOISE EMITTED FROM THE VEHICLE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 174,000.
NHTSA ODI #10664283
134,000 miles · May 25, 2012
Steering
CAR WAS DRIVING DOWN THE ROAD AND POWER STEERING FLUID HOSES FELL OFF AND POWER STEERING FAILED COMPLETELY. I WAS ABLE TO STEER THE VEHICLE OFF THE ROAD AND REATTACH THE HOSES THE BEST I COULD. WE TOOK THE VEHICLE IN FOR THE POWER STEERING HOSE CLAMP RECALL AND MB PERFORMED THE REPLACEMENT. THIS YEAR, THE CLAMPS CAME OFF AGAIN A…
Read full complaint
CAR WAS DRIVING DOWN THE ROAD AND POWER STEERING FLUID HOSES FELL OFF AND POWER STEERING FAILED COMPLETELY. I WAS ABLE TO STEER THE VEHICLE OFF THE ROAD AND REATTACH THE HOSES THE BEST I COULD. WE TOOK THE VEHICLE IN FOR THE POWER STEERING HOSE CLAMP RECALL AND MB PERFORMED THE REPLACEMENT. THIS YEAR, THE CLAMPS CAME OFF AGAIN AND THE RACK ITSELF WAS DAMAGED AND PROFUSELY LEAKS FLUID NOW. THE NEW HOSE CLAMPS HAVE NOT FIXED THE PROBLEM AND HAVE CAUSED FURTHER DAMAGE TO THE STEERING SYSTEM AS A WHOLE. *TR
NHTSA ODI #10459627
75,000 miles · Jan 31, 2012
Steering
TL* THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE CONTACT STATED THAT POWER STEERING FLUID WAS LEAKING, RESULTING IN POWER STEERING FAILURE WHILE DRIVING. THE VEHICLE WAS REPAIRED UNDER NHTSA CAMPAIGN ID NUMBER: 08V465000 (STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS), BUT THE FAILURE RECURRED AFTER REPAIRS.…
Read full complaint
TL* THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE CONTACT STATED THAT POWER STEERING FLUID WAS LEAKING, RESULTING IN POWER STEERING FAILURE WHILE DRIVING. THE VEHICLE WAS REPAIRED UNDER NHTSA CAMPAIGN ID NUMBER: 08V465000 (STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS), BUT THE FAILURE RECURRED AFTER REPAIRS. THE DEALER AND THE MANUFACTURER WERE NOTIFIED OF THE FAILURE, BUT DENIED ANY ASSISTANCE WITH REPAIR TO THE VEHICLE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 75,000 AND THE CURRENT MILEAGE WAS 100,000.
NHTSA ODI #10446000
86,000 miles · Feb 12, 2010
Steering
MY 2000 MERCEDES BENZ ML430 HAS A SEVERE POWER STEERING LEAKAGE. TWO RECALLS BY THE NHTSA HAVE BEEN ISSUED. THE DEALERSHIP CLAIMS THAT MY LEAKAGE IS DUE TO SEVERE LEAKAGE AT THE POWER STEERING RACK SEALS AND RESERVOIR. I WANT TO NOTIFY THE NHTSA THAT THERE ARE MECHANICAL FAILURES RELATED TO THE POWER STEERING LEAKAGE THAT MAY …
Read full complaint
MY 2000 MERCEDES BENZ ML430 HAS A SEVERE POWER STEERING LEAKAGE. TWO RECALLS BY THE NHTSA HAVE BEEN ISSUED. THE DEALERSHIP CLAIMS THAT MY LEAKAGE IS DUE TO SEVERE LEAKAGE AT THE POWER STEERING RACK SEALS AND RESERVOIR. I WANT TO NOTIFY THE NHTSA THAT THERE ARE MECHANICAL FAILURES RELATED TO THE POWER STEERING LEAKAGE THAT MAY BE IN ADDITION TO THE SPECIFIC RECALL ISSUES AND THE DEALERSHIP/MB DECLINES TO ADDRESS WITHOUT COMPENSATION. MY VEHICLE HAS 88,900 MILES I HAVE LOST POWER STEERING WHILE DRIVING DOWN THE HIGHWAY AT 65 MPH AND MUST CHECK THE FLUID LEVELS CONSTANTLY. I HAVE BEEN FORTUNATE TO HAVE NOT EXPERIENCED A MAJOR ACCIDENT. *TR
NHTSA ODI #10310059
83,000 miles · Feb 2, 2010
Steering
TL*THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE CONTACT STATED THAT THERE WAS A POWER STEERING RECALL RELATED TO THE HOSE AND THE CLAMP ON THE RACK AND PINION. THE CONTACT HAS EXPERIENCED POWER STEERING FAILURE. THE DEALER ADVISED THE CONTACT THAT THEY ARE ONLY REQUIRED TO MAKE THE REPAIRS ACCORDING TO RECALL#03V121000, STEE…
Read full complaint
TL*THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE CONTACT STATED THAT THERE WAS A POWER STEERING RECALL RELATED TO THE HOSE AND THE CLAMP ON THE RACK AND PINION. THE CONTACT HAS EXPERIENCED POWER STEERING FAILURE. THE DEALER ADVISED THE CONTACT THAT THEY ARE ONLY REQUIRED TO MAKE THE REPAIRS ACCORDING TO RECALL#03V121000, STEERING, HYDRAULIC POWER ASSIST HOSE, PIPING, AND CONNECTIONS. THE FAILURE MILEAGE WAS 83,000.
NHTSA ODI #10303918
95,000 miles · Apr 17, 2009
Steering
TOOK THE 2000 ML430 IN FOR RECALL IN 11/08. CAR STARTED MAKING SAME NOISE AS BEFORE. TOOK IT BACK FOR THEM TO RE-FIX IT AGAIN. THEY REFUSED. WANTED ME TO PAY 285. SAID EVEN THOUGH CAR ACTED THE SAME AND WAS STILL LEAKING FLUID, IT WASN'T A RECALL REPAIR. I DISAGREE. I DON'T HAVE 285!!! I PUT MORE POWER STEERING FLUID IN AND LEFT…
Read full complaint
TOOK THE 2000 ML430 IN FOR RECALL IN 11/08. CAR STARTED MAKING SAME NOISE AS BEFORE. TOOK IT BACK FOR THEM TO RE-FIX IT AGAIN. THEY REFUSED. WANTED ME TO PAY 285. SAID EVEN THOUGH CAR ACTED THE SAME AND WAS STILL LEAKING FLUID, IT WASN'T A RECALL REPAIR. I DISAGREE. I DON'T HAVE 285!!! I PUT MORE POWER STEERING FLUID IN AND LEFT. IT'S STILL DOING THE SAME THING. *TR
NHTSA ODI #10265698
85,000 miles · Mar 23, 2009
Steering
TL*THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE VEHICLE WAS PREVIOUSLY REPAIRED ACCORDING TO NHTSA CAMPAIGN ID NUMBER 03V121000 (STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS). AFTER THE REPAIR WAS PERFORMED, THE CONTACT STILL EXPERIENCED FAILURES. WHEN THE STEERING WHEEL WAS TURNED TO THE LEFT OR RIGHT, I…
Read full complaint
TL*THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. THE VEHICLE WAS PREVIOUSLY REPAIRED ACCORDING TO NHTSA CAMPAIGN ID NUMBER 03V121000 (STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS). AFTER THE REPAIR WAS PERFORMED, THE CONTACT STILL EXPERIENCED FAILURES. WHEN THE STEERING WHEEL WAS TURNED TO THE LEFT OR RIGHT, IT WOULD MAKE A NOISE AS IF THERE WERE NO POWER STEERING FLUID IN THE VEHICLE. THE MANUFACTURER ISSUED A SECOND RECALL (NHTSA CAMPAIGN ID NUMBER 08V465000), WHICH STATED THAT AN EARLIER RECALL REPAIR PERFORMED MAY BE INSUFFICIENT IN PREVENTING A FUTURE LEAKAGE OR FAILURE OF THE POWER STEERING HOSE CONNECTION (PLEASE SEE 03V121). SINCE IT IS NOT POSSIBLE THROUGH INSPECTION TO IDENTIFY SPECIFIC VEHICLES THAT MAY NOT HAVE BEEN PROPERLY REPAIRED, ALL VEHICLES REPAIRED PRIOR TO NOVEMBER 15, 2003 WILL BE REPAIRED AGAIN. THE CONTACT HAD THE REPAIRS PERFORMED IN 2004 AND WAS INFORMED THAT HIS VIN WAS NOT INCLUDED IN THE RECALL EXTENSION. NO REPAIRS HAVE BEEN MADE TO CORRECT THE FAILURE. THE FAILURE AND CURRENT MILEAGES WERE LESS THAN 85,000.
NHTSA ODI #10262792
Mileage unknown · Dec 9, 2008
Steering
TL*THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. WHILE DRIVING APPROXIMATELY 10 MPH ON NORMAL ROAD CONDITIONS, THE POWER STEERING FAILED. THE CONTACT PULLED THE VEHICLE OVER, INSPECTED UNDERNEATH THE HOOD, AND NOTICED POWER STEERING FLUID LEAKING. THERE WERE NO WARNING INDICATORS ILLUMINATED ON THE INSTRUMENT PANEL. THE VEHIC…
Read full complaint
TL*THE CONTACT OWNS A 2000 MERCEDES BENZ ML430. WHILE DRIVING APPROXIMATELY 10 MPH ON NORMAL ROAD CONDITIONS, THE POWER STEERING FAILED. THE CONTACT PULLED THE VEHICLE OVER, INSPECTED UNDERNEATH THE HOOD, AND NOTICED POWER STEERING FLUID LEAKING. THERE WERE NO WARNING INDICATORS ILLUMINATED ON THE INSTRUMENT PANEL. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC AND REPAIRED ACCORDING TO NHTSA CAMPAIGN ID NUMBER 08V465000 (STEERING:HYDRAULIC POWER ASSIST,HOSE, PIPING, AND CONNECTIONS). THE RECALL REMEDY WAS UNSUCCESSFUL BECAUSE THE FAILURE RECURRED THE FOLLOWING DAY. THE VEHICLE IS CURRENTLY BEING REPAIRED. THE FAILURE MILEAGE WAS UNKNOWN AND THE CURRENT MILEAGE WAS 130,000.
NHTSA ODI #10251172
74,686 miles · May 25, 2005
Steering
2000 MERCEDES BENZ ML430 HOSE CLAMP CAME OFF AND THERE WAS NO POWER STEERING FLUID IN THE PUMP RESULTING IN THE STEERING BECOMING STIFF.***NO ANSWER REQUIRED***. *MR THE POWER STEERING HOSE AND CLAMP WERE REPLACED UNDER RECALL THE POWER STEERING RACK ALSO LEAKED AND NEEDED TO BE REPLACED. THE CONSUMER FEELS THAT THE RACK FAI…
Read full complaint
2000 MERCEDES BENZ ML430 HOSE CLAMP CAME OFF AND THERE WAS NO POWER STEERING FLUID IN THE PUMP RESULTING IN THE STEERING BECOMING STIFF.***NO ANSWER REQUIRED***. *MR THE POWER STEERING HOSE AND CLAMP WERE REPLACED UNDER RECALL THE POWER STEERING RACK ALSO LEAKED AND NEEDED TO BE REPLACED. THE CONSUMER FEELS THAT THE RACK FAILED AS A RESULT OF THE CLAMP FAILURE AND BELIEVES IT SHOULD HAVE BEEN REPLACED FREE OF CHARGE. *NM
NHTSA ODI #10124687
NHTSA investigations
4PE10050 · Brake Lamp Switch Failure.
Opened Dec 21, 2010 · Closed May 4, 2011
Status: closed (inferred from source dates) · Exterior Lighting:brake Lights:switch; Service Brakes, Hydraulic; Vehicle Speed Control; Vehicle Speed Control:cruise Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Additional source detail variants (4)
Exterior Lighting:brake Lights:switch
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Service Brakes, Hydraulic
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Vehicle Speed Control:cruise Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
Vehicle Speed Control
ODI opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.Consumers also reported the illumination of a warning lamp on the instrument panel.The switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.As installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.One set of contacts (BLS) operates the stop lamps, a second set (EWM) controls the shift interlock system, and a third set (BS) is used by an on-board diagnostic (OBD) system to monitor switch operation.The cruise control monitors the BLS signal to determine when the brake is applied, the primary way the system is disabled when set.The relative timing of contact actuation in response to plunger movement allows the OBD system to detect a switch fault.When a fault is detected a malfunction indication lamp (MIL) is illuminated (driver alert), a diagnostic trouble code (DTC) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).In its response to ODI's January 2011 information request letter, MB explained its assessment of switch failures which was based primarily on evaluation of field return failures.MB identified both 1) electrical contact and 2) mechanical switch failure mechanisms.According to MB's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.For instance MB claims that BLS contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the OBD system, resulting in a DTC and subsequent replacement.Electrical contact failures of the BS and EWM contacts result in a DTC also, and EWM contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).Accordingly MB maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.MB determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.High temperatures occur due to overheating of the BLS contacts and can cause the internal plastic components to melt.In one scenario overheated BLS contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.In another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.In this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.Additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.In its March 31, 2011 defect notification, MB stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11V-208) to replace the switch with a more robustly designed component.The recall includes 136,751 model year 2000 - 2002 M-Class and model year 2000 - 2004 M-Class AMG vehicles.Owner notification letters will be mailed
EA08009 · Brake Line Chafe
Opened Apr 28, 2008 · Closed Dec 16, 2009
Status: closed (inferred from source dates) · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings; Service Brakes, Hydraulic:foundation Components:hoses, Lines/piping, And Fittings
ANALYSIS OF COMPLAINTS TO ODI AND MERCEDES AND WARRANTY CLAIM DATA SUBMITTED BY MERCEDES INDICATES THAT THE ALLEGED DEFECT HAS OCCURRED AT A LOW RATE (36.5 COMPLAINTS PER 100,000 VEHICLES AND 0.29 PERCENT WARRANTY CLAIM RATE), WITH NO DISCERNABLE DEFECT TREND INDICATING THAT THE RATE OF CHAFING RELATED BRAKE LINE FAILURES IS INCREASING.THERE HAVE BEEN NO NEW COMPLAINTS SINCE JANUARY 2009.WHEN THE ANALYSIS IS LIMITED TO INCIDENTS OF BRAKE LINE LEAKAGE THAT RESULTED IN ALLEGATIONS OF REDUCED BRAKE EFFECTIVENESS, THE RATE DROPS EVEN FURTHER (22.3 COMPLAINTS PER 100,000 VEHICLES AND 0.04 PERCENT WARRANTY CLAIM RATE). MERCEDES PROVIDED DATA SHOWING THAT IN THE RARE INSTANCES WHEN CHAFING DID PROGRESS TO BRAKE LINE LEAKAGE THE DRIVER WOULD BE IMMEDIATELY ALERTED TO A PROBLEM BY ILLUMINATION OF THE BRIGHT YELLOW ESP/BAS WARNING LAMP AND CHANGES IN BRAKE PEDAL FEEL.CONTINUED OPERATION WITH A LEAKING BRAKE LINE WOULD RESULT IN ILLUMINATION OF THE BRIGHT RED BRAKE WARNING LAMP AND AN AUDIBLE CHIME DUE TO LOW MASTER CYLINDER RESERVOIR LEVEL. CONTINUED OPERATION WITH THE BRAKE WARNING LAMP ILLUMINATED WOULD ULTIMATELY DRAIN THE RESERVOIR FOR THE AFFECTED CIRCUIT, RESULTING IN LOSS OF THE CIRCUIT AND AN APPROXIMATELY 80% INCREASE IN STOPPING DISTANCES. SURVEYS CONDUCTED BY ODI AND VRTC INDICATE THAT ROUTING ANOMALIES MAY BE MORE COMMON THAN THE COMPLAINT AND WARRANTY DATA SUGGEST FOR THE SUBJECT LINE BUNDLE, WITH LINE CONTACT OR OTHER ROUTING ANOMALY NOTED IN 13 OF 51 VEHICLES SURVEYED BY ODI AND VRTC (25.5%).WHILE EVIDENCE OF CONTACT BETWEEN THE FUEL LINE AND SUBJECT BRAKE IN A PARTICULAR VEHICLE IS NOT NECESSARILY PREDICTIVE OF EVENTUAL LINE FAILURE/LEAKAGE, SIGNIFICANT CHAFING WEAR WAS NOTED IN TWO SURVEY VEHICLES (3.9%).TO ADDRESS CONCERNS WITH LINE ROUTING AND ENSURE THAT LINES WITH EVIDENT CHAFING DO NOT PROGRESS TO A LEAK CONDITION, MERCEDES WILL CONDUCT AN OWNER NOTIFICATION PROGRAM INSTRUCTING OWNERS TO BRING THE VEHICLES TO A DEALER FOR A FREE INSPECTION AND REPAIR.LINES THAT DO NOT HAVE A SPACER (RUBBER GROMMET OR OMEGA-CLIP) BETWEEN THE SUBJECT FUEL AND BRAKE LINES WILL HAVE AN OMEGA-CLIP SPACER INSTALLED TO ENSURE ADEQUATE CLEARANCE BETWEEN THE LINES.BRAKE LINES WITH CHAFE MARKS WILL BE REPLACED. ACCORDINGLY, THIS INVESTIGATION HAS BEEN CLOSED. THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST. THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED. FOR ADDITIONAL INFORMATION REGARDING THIS ENGINEERING ANALYSIS REFER TO THE EA08-009 CLOSING REPORT.
Additional source detail variants (2)
Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings
ANALYSIS OF COMPLAINTS TO ODI AND MERCEDES AND WARRANTY CLAIM DATA SUBMITTED BY MERCEDES INDICATES THAT THE ALLEGED DEFECT HAS OCCURRED AT A LOW RATE (36.5 COMPLAINTS PER 100,000 VEHICLES AND 0.29 PERCENT WARRANTY CLAIM RATE), WITH NO DISCERNABLE DEFECT TREND INDICATING THAT THE RATE OF CHAFING RELATED BRAKE LINE FAILURES IS INCREASING.THERE HAVE BEEN NO NEW COMPLAINTS SINCE JANUARY 2009.WHEN THE ANALYSIS IS LIMITED TO INCIDENTS OF BRAKE LINE LEAKAGE THAT RESULTED IN ALLEGATIONS OF REDUCED BRAKE EFFECTIVENESS, THE RATE DROPS EVEN FURTHER (22.3 COMPLAINTS PER 100,000 VEHICLES AND 0.04 PERCENT WARRANTY CLAIM RATE). MERCEDES PROVIDED DATA SHOWING THAT IN THE RARE INSTANCES WHEN CHAFING DID PROGRESS TO BRAKE LINE LEAKAGE THE DRIVER WOULD BE IMMEDIATELY ALERTED TO A PROBLEM BY ILLUMINATION OF THE BRIGHT YELLOW ESP/BAS WARNING LAMP AND CHANGES IN BRAKE PEDAL FEEL.CONTINUED OPERATION WITH A LEAKING BRAKE LINE WOULD RESULT IN ILLUMINATION OF THE BRIGHT RED BRAKE WARNING LAMP AND AN AUDIBLE CHIME DUE TO LOW MASTER CYLINDER RESERVOIR LEVEL. CONTINUED OPERATION WITH THE BRAKE WARNING LAMP ILLUMINATED WOULD ULTIMATELY DRAIN THE RESERVOIR FOR THE AFFECTED CIRCUIT, RESULTING IN LOSS OF THE CIRCUIT AND AN APPROXIMATELY 80% INCREASE IN STOPPING DISTANCES. SURVEYS CONDUCTED BY ODI AND VRTC INDICATE THAT ROUTING ANOMALIES MAY BE MORE COMMON THAN THE COMPLAINT AND WARRANTY DATA SUGGEST FOR THE SUBJECT LINE BUNDLE, WITH LINE CONTACT OR OTHER ROUTING ANOMALY NOTED IN 13 OF 51 VEHICLES SURVEYED BY ODI AND VRTC (25.5%).WHILE EVIDENCE OF CONTACT BETWEEN THE FUEL LINE AND SUBJECT BRAKE IN A PARTICULAR VEHICLE IS NOT NECESSARILY PREDICTIVE OF EVENTUAL LINE FAILURE/LEAKAGE, SIGNIFICANT CHAFING WEAR WAS NOTED IN TWO SURVEY VEHICLES (3.9%).TO ADDRESS CONCERNS WITH LINE ROUTING AND ENSURE THAT LINES WITH EVIDENT CHAFING DO NOT PROGRESS TO A LEAK CONDITION, MERCEDES WILL CONDUCT AN OWNER NOTIFICATION PROGRAM INSTRUCTING OWNERS TO BRING THE VEHICLES TO A DEALER FOR A FREE INSPECTION AND REPAIR.LINES THAT DO NOT HAVE A SPACER (RUBBER GROMMET OR OMEGA-CLIP) BETWEEN THE SUBJECT FUEL AND BRAKE LINES WILL HAVE AN OMEGA-CLIP SPACER INSTALLED TO ENSURE ADEQUATE CLEARANCE BETWEEN THE LINES.BRAKE LINES WITH CHAFE MARKS WILL BE REPLACED. ACCORDINGLY, THIS INVESTIGATION HAS BEEN CLOSED. THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST. THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED. FOR ADDITIONAL INFORMATION REGARDING THIS ENGINEERING ANALYSIS REFER TO THE EA08-009 CLOSING REPORT.
Service Brakes, Hydraulic:foundation Components:hoses, Lines/piping, And Fittings
ANALYSIS OF COMPLAINTS TO ODI AND MERCEDES AND WARRANTY CLAIM DATA SUBMITTED BY MERCEDES INDICATES THAT THE ALLEGED DEFECT HAS OCCURRED AT A LOW RATE (36.5 COMPLAINTS PER 100,000 VEHICLES AND 0.29 PERCENT WARRANTY CLAIM RATE), WITH NO DISCERNABLE DEFECT TREND INDICATING THAT THE RATE OF CHAFING RELATED BRAKE LINE FAILURES IS INCREASING.THERE HAVE BEEN NO NEW COMPLAINTS SINCE JANUARY 2009.WHEN THE ANALYSIS IS LIMITED TO INCIDENTS OF BRAKE LINE LEAKAGE THAT RESULTED IN ALLEGATIONS OF REDUCED BRAKE EFFECTIVENESS, THE RATE DROPS EVEN FURTHER (22.3 COMPLAINTS PER 100,000 VEHICLES AND 0.04 PERCENT WARRANTY CLAIM RATE). MERCEDES PROVIDED DATA SHOWING THAT IN THE RARE INSTANCES WHEN CHAFING DID PROGRESS TO BRAKE LINE LEAKAGE THE DRIVER WOULD BE IMMEDIATELY ALERTED TO A PROBLEM BY ILLUMINATION OF THE BRIGHT YELLOW ESP/BAS WARNING LAMP AND CHANGES IN BRAKE PEDAL FEEL.CONTINUED OPERATION WITH A LEAKING BRAKE LINE WOULD RESULT IN ILLUMINATION OF THE BRIGHT RED BRAKE WARNING LAMP AND AN AUDIBLE CHIME DUE TO LOW MASTER CYLINDER RESERVOIR LEVEL. CONTINUED OPERATION WITH THE BRAKE WARNING LAMP ILLUMINATED WOULD ULTIMATELY DRAIN THE RESERVOIR FOR THE AFFECTED CIRCUIT, RESULTING IN LOSS OF THE CIRCUIT AND AN APPROXIMATELY 80% INCREASE IN STOPPING DISTANCES. SURVEYS CONDUCTED BY ODI AND VRTC INDICATE THAT ROUTING ANOMALIES MAY BE MORE COMMON THAN THE COMPLAINT AND WARRANTY DATA SUGGEST FOR THE SUBJECT LINE BUNDLE, WITH LINE CONTACT OR OTHER ROUTING ANOMALY NOTED IN 13 OF 51 VEHICLES SURVEYED BY ODI AND VRTC (25.5%).WHILE EVIDENCE OF CONTACT BETWEEN THE FUEL LINE AND SUBJECT BRAKE IN A PARTICULAR VEHICLE IS NOT NECESSARILY PREDICTIVE OF EVENTUAL LINE FAILURE/LEAKAGE, SIGNIFICANT CHAFING WEAR WAS NOTED IN TWO SURVEY VEHICLES (3.9%).TO ADDRESS CONCERNS WITH LINE ROUTING AND ENSURE THAT LINES WITH EVIDENT CHAFING DO NOT PROGRESS TO A LEAK CONDITION, MERCEDES WILL CONDUCT AN OWNER NOTIFICATION PROGRAM INSTRUCTING OWNERS TO BRING THE VEHICLES TO A DEALER FOR A FREE INSPECTION AND REPAIR.LINES THAT DO NOT HAVE A SPACER (RUBBER GROMMET OR OMEGA-CLIP) BETWEEN THE SUBJECT FUEL AND BRAKE LINES WILL HAVE AN OMEGA-CLIP SPACER INSTALLED TO ENSURE ADEQUATE CLEARANCE BETWEEN THE LINES.BRAKE LINES WITH CHAFE MARKS WILL BE REPLACED. ACCORDINGLY, THIS INVESTIGATION HAS BEEN CLOSED. THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST. THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED. FOR ADDITIONAL INFORMATION REGARDING THIS ENGINEERING ANALYSIS REFER TO THE EA08-009 CLOSING REPORT.
PE07007 · Electronic Stability Control Malfunction
Opened Feb 1, 2007 · Closed Jul 11, 2007
Status: closed (inferred from source dates) · Electronic Stability Control:automatic (asc)
ODI OPENED PE07-007 AFTER RECEIVING 4 COMPLAINTS WITHIN A 6 WEEK PERIOD ALLEGING INCIDENTS OF UNCOMMANDED BRAKE APPLICATION IN MODEL YEAR (MY) 2000 THROUGH 2001 MERCEDES M CLASS SPORT UTILITY VEHICLES.INFORMATION CONTAINED IN THE REPORTS OR GATHERED IN SUBSEQUENT CONSUMER INTERVIEWS INDICATED THAT THE INCIDENTS WERE CAUSED BY FAULTS IN THE ELECTRONIC STABILITY PROGRAM (ESP) SYSTEM WHICH WERE REPAIRED BY REPLACING THE YAW RATE SENSORS.ALTHOUGH THE SAME YAW RATE SENSOR IS USED IN APPROXIMATELY 800,000 OTHER MERCEDES M-CLASS, C-CLASS AND SLK MODELS, TO DATE THERE HAS BEEN ONLY ONE RELATED COMPLAINT TO ODI IN THOSE VEHICLES. DURING THIS INVESTIGATION MERCEDES BENZ PROVIDED ODI WITH 327 COMPLAINTS RELATED TO THE ESP SYSTEM IN THE MY 2000 THROUGH 2001 M CLASS VEHICLES.SEVEN OF THE COMPLAINTS SUBMITTED BY MERCEDES ALLEGED INCIDENTS OF UNCOMMANDED BRAKE ACTIVATION WHILE DRIVING, WITH TWO OF THESE INVOLVING VEHICLES IDENTIFIED IN THE ODI COMPLAINTS.NONE OF THE INCIDENTS RESULTED IN CRASH OR INJURY.HOWEVER, THE OWNERS DID EXPRESS SAFETY CONCERNS DUE TO THE SUDDEN, UNEXPECTED CHANGE IN VEHICLE SPEED AND DIRECTION. ON MAY 10, 2007 MERCEDES BENZ MET WITH NHTSA TO PROVIDE A TECHNICAL PRESENTATION AND CONDUCT A DRIVING DEMONSTRATION OF THE ESP SYSTEM PERFORMANCE WITH SIMULATED ELECTRICAL FAULTS IN THE YAW RATE SENSOR.MERCEDES SHOWED THAT THE ESP SYSTEM IS PROGRAMMED TO DIAGNOSE ELECTRICAL FAULTS AND THAT BRAKE APPLICATIONS RESULTING FROM YAW RATE SENSOR ELECTRICAL FAULTS ARE VERY SHORT IN DURATION (0.3 SECONDS OR LESS) AND DO NOT AFFECT VEHICLE CONTROL OR STABILITY. NINE OF THE CONSUMER COMPLAINTS TO ODI AND MERCEDES ALLEGED BRAKE ACTIVATIONS LONGER THAN 0.3 SECONDS, WITH SEVERAL ALLEGING THAT THE INCIDENT LASTED UNTIL THE VEHICLE CAME TO A STOP.A COMPLAINT VEHICLE THAT ALLEGED MULTIPLE INCIDENTS WAS EVALUATED BY ODI AT THE VEHICLE RESEARCH AND TEST CENTER (VRTC) IN EAST LIBERTY, OHIO.VRTC WAS UNABLE TO DUPLICATE THE CONDITION.DUE TO THE LOW COMPLAINT RATE AND ONLY ONE NEW COMPLAINT TO ODI OR MERCEDES SINCE JANUARY 2007, THIS INVESTIGATION HAS BEEN CLOSED.ODI WILL CONTINUE TO MONITOR COMPLAINTS IN THE SUBJECT VEHICLES AND OTHER MERCEDES PRODUCTS USING THE SAME YAW RATE SENSOR AND MERCEDES WILL PROVIDE UPDATES ON FIELD EXPERIENCE (COMPLAINTS, FIELD REPORTS AND WARRANTY CLAIMS) THROUGH THE END OF 2007.
PE03058 · Engine Crankshaft Pulley Failure
Opened Dec 17, 2003 · Closed Apr 22, 2004
Status: closed (inferred from source dates) · Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED THIS PRELIMINARY EVALUATION TO INVESTIGATE ALLEGATIONS OF ENGINE CRANKSHAFT PULLEY HARMONIC BALANCER FAILURE THAT COULD RESULT IN LOSS OF POWER-STEERING ASSIST.ODI HAS RECEIVED A TOTAL OF 546 NON-DUPLICATIVE REPORTS THAT ALLEGE ENGINE CRANKSHAFT PULLEY HARMONIC BALANCER FAILURE ON ALL MERCEDES-BENZ VEHICLES USING THE SUBJECT COMPONENT.THE SUBJECT COMPONENT FAILURES ARE PROGRESSIVE IN NATURE AND ONLY A SMALL PERCENTAGE OF THE COMPLAINTS AND WARRANT CLAIMS INVOLVED A FAILURE THAT HAD PROGRESSED FAR ENOUGH TO EFFECT POWER STEERING PERFORMANCE (6 OF 55 ODI COMPLAINTS REFERENCE INCREASED STEERING EFFORT).THERE HAVE BEEN NO CRASHES OR INJURIES RELATED TO THE ALLEGED DEFECT.A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.SEE SUMMARY REPORT ATTACHED FOR FURTHER DETAIL.
Illustration