When problems were reported
Mileage at the reported incident
Limited mileage data: 0 of 0 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
NHTSA owner reports · September 18, 2026 snapshot.
Official recalls
8Dec 10, 2025
Motor Coach Industries (MCI) is recalling certain 102DL3, 102D3, MC12PTV, E4500, D4000, 102D3ISTV, D4500, J4500, D4000ISTV, D4005, D4505, and J3500 transit buses. Please refer to MCI's recall report for specific model year information. The front door lower curb view glazing material is incorrect. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) number 205, "Glazing Materials."
Consequence & remedy
Consequence: The incorrect window glazing material may reduce the driver's visibility, increasing the risk of a crash.
Remedy: MCI will replace the glass, free of charge. Owner notification letters were mailed February 4, 2026. Owners may contact MCI customer service at 1-800-241-2947. MCI's number for this recall is 22-005.
Additional source detail variants (2)
Visibility:glass, Side/rear
Motor Coach Industries (MCI) is recalling certain 102DL3, 102D3, MC12PTV, E4500, D4000, 102D3ISTV, D4500, J4500, D4000ISTV, D4005, D4505, and J3500 transit buses. Please refer to MCI's recall report for specific model year information. The front door lower curb view glazing material is incorrect. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) number 205, "Glazing Materials."
Consequence: The incorrect window glazing material may reduce the driver's visibility, increasing the risk of a crash.
Remedy: MCI will replace the glass, free of charge. Owner notification letters were mailed February 4, 2026. Owners may contact MCI customer service at 1-800-241-2947. MCI's number for this recall is 22-005.
Structure:body:door
Motor Coach Industries (MCI) is recalling certain 102DL3, 102D3, MC12PTV, E4500, D4000, 102D3ISTV, D4500, J4500, D4000ISTV, D4005, D4505, and J3500 transit buses. Please refer to MCI's recall report for specific model year information. The front door lower curb view glazing material is incorrect. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) number 205, "Glazing Materials."
Consequence: The incorrect window glazing material may reduce the driver's visibility, increasing the risk of a crash.
Remedy: MCI will replace the glass, free of charge. Owner notification letters were mailed February 4, 2026. Owners may contact MCI customer service at 1-800-241-2947. MCI's number for this recall is 22-005.
Sep 23, 2021
Motor Coach Industries (MCI) is recalling certain 2005-2009 E4500 and 2005-2012 J4500 motorcoaches equipped with Ricon Baylift Wheelchair Lifts. When the lift's outer barrier is fully deployed, it may not withstand a sufficient amount of force, which could cause it to fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 403, "Platform Lift Systems," and number 404, "Platform lift installations."
Consequence & remedy
Consequence: In the event that a mobility device pushes into the outer barrier, the barrier may fail, increasing the risk of injury for the lift occupant.
Remedy: Ricon will reinforce the outer barrier with additional supports, free of charge. Owner notification letters were mailed on October 18, 2021. Owners may contact the Ricon's Customer Service at (800) 322-2884, or email Ricons Recall Coordinator, at admin21e068@Wabtec.com or by locating the nearest Ricon servicing dealer using the locator on the Ricon website www.riconcorp.com. Owners may also contact MCI's customer service at 1-800-241-2947. MCI's number for this recall is R21-024.
Jan 7, 2019
Motor Coach Industries (MCI) is recalling certain 2001-2015 J4500 and 1997-2013 102EL3/E4500 coaches equipped with a hydraulic rear axle (tag axle) steering system. The axle's alignment and low hydraulic pressure in the steering system may cause the steering system to lock, causing a loss of steering control at highway speeds.
Consequence & remedy
Consequence: Loss of steering control may increase the risk of a crash.
Remedy: MCI will inspect and repair axle alignment, as necessary, free of charge. MCI issued owners an interim notification on March 26, 2019. Owner notification letters were mailed on May 14, 2021. Owners may contact MCI customer service at 1-800-241-2947. MCI's number for this recall is SB 469.
Mar 30, 2015
Motor Coach Industries (MCI) is recalling certain model year 2007-2010 MCI E4500 and J4500 motor coaches manufactured November 21, 2006, to August 27, 2009, and equipped with certain Recaro Automotive Seating Ergo M bus driver seats. The affected seats were manufactured in a way that the tether bar may push into the retractor panel door and potentially interfere with the seat belt locking mechanism.
Consequence & remedy
Consequence: If the seat belt locking mechanism does not function as intended, the bus driver may not be properly restrained, increasing the risk of personal injury in the event of a crash.
Remedy: MCI will notify owners , and dealers will inspect and retrofit the seats free of charge. The recall began on May 14, 2015. Owners may contact MCI customer service at 1-800-241-2947.
Apr 4, 2014
Motor Coach Industries (MCI) is recalling certain model year 2009-2014 E4500 and J4500 motorcoaches manufactured October 2008 through October 2013, and equipped with passenger seats with 3-point seat belts. The seat track for the second row passenger seats may be missing a weld at the end of the seat track where it enters the frame structure.
Consequence & remedy
Consequence: In the event of a crash, the seat may detach from its floor mounting, increasing the risk of injury to the occupant.
Remedy: MCI will notify owners, and dealers will modify the seat anchorage, free of charge. The recall began on May 9, 2014. Owners may contact MCI at 1-800-241-2947. MCI's number for this recall is 408.
Additional source detail variants (2)
Seats
Motor Coach Industries (MCI) is recalling certain model year 2009-2014 E4500 and J4500 motorcoaches manufactured October 2008 through October 2013, and equipped with passenger seats with 3-point seat belts. The seat track for the second row passenger seats may be missing a weld at the end of the seat track where it enters the frame structure.
Consequence: In the event of a crash, the seat may detach from its floor mounting, increasing the risk of injury to the occupant.
Remedy: MCI will notify owners, and dealers will modify the seat anchorage, free of charge. The recall began on May 9, 2014. Owners may contact MCI at 1-800-241-2947. MCI's number for this recall is 408.
Seat Belts:front:anchorage
Motor Coach Industries (MCI) is recalling certain model year 2009-2014 E4500 and J4500 motorcoaches manufactured October 2008 through October 2013, and equipped with passenger seats with 3-point seat belts. The seat track for the second row passenger seats may be missing a weld at the end of the seat track where it enters the frame structure.
Consequence: In the event of a crash, the seat may detach from its floor mounting, increasing the risk of injury to the occupant.
Remedy: MCI will notify owners, and dealers will modify the seat anchorage, free of charge. The recall began on May 9, 2014. Owners may contact MCI at 1-800-241-2947. MCI's number for this recall is 408.
Oct 17, 2013
Motor Coach Industries (MCI) is recalling certain model year 2000-2012 D, E, G and J series coaches manufactured January 2000 through June 2011 and equipped with Sure Power battery equalizers containing a particular epoxy sealing, aka 'potting', compound. The specific potting compound used in the subject products for insulation was found to be capable of conducting electricity after being exposed to heat.
Consequence & remedy
Consequence: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.
Remedy: MCI will notify owners, and Sure Power will replace the equalizers, free of charge. Owners may contact MCI at 1-847-285-2000. This campaign is MCI service bulletin 401.
Oct 26, 2011
MOTOR COACH INDUSTRIES (MCI) IS RECALLING CERTAIN MODEL YEAR 2003, AND 2007-2012 E AND J MODELS ALONG WITH MODEL YEAR 2007-2012 D4000, D4005, D4500, D4505, D4000ISTV MOTOR COACHES EQUIPPED WITH MERITOR WABCO ELECTRONIC STABILITY CONTROL (ESC) MODULES, MANUFACTURED FROM OCTOBER 2002, THROUGH OCTOBER 2011. UNDER CERTAIN ROAD AND DRIVING CONDITIONS, VEHICLE BODY ROLL AND ROAD INCLINATION CHARACTERISTICS MAY ADVERSELY AFFECT THE SLIP ANGLE CALCULATION OF THE ELECTRONIC STABILITY CONTROL (ESC) SYSTEM. THIS MIGHT CAUSE THE ESC TO PERCEIVE AN OVER STEERING SITUATION AND THEREFORE APPLY THE OUTER WHEEL BRAKE ON THE FRONT AXLE UNTIL THE VEHICLE IS PERCEIVED TO BE STABLE.
Consequence & remedy
Consequence: IF THE DRIVER IS SLOW TO REACT DURING THIS ESC INTERVENTION, THE VEHICLE MAY DEVIATE FROM THE INTENDED LINE OF TRAVEL, INCREASING THE RISK OF A CRASH.
Remedy: MCI WILL NOTIFY OWNERS AND REPLACE THE CONTROL MODULE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 4, 2012. OWNERS MAY CONTACT MCI CUSTOMER SERVICE AT 1-800-241-2947.
Apr 6, 2010
MCI IS RECALLING CERTAIN MODEL YEAR 1999-2001, 2007-2011 E4500 AND MODEL YEAR 2001-2011 J4500 COACHES EQUIPPED WITH DOGA WINDSHIELD MOTORS. THE WINDSHIELD WIPER MOTOR MAY FAIL TO OPERATE PROPERLY WHILE THE WIPER SYSTEM IS FUNCTIONING. IF THIS OCCURS, THE WINDSHIELD WIPERS MAY OPERATE INTERMITTENTLY, OPERATE AT A SINGLE SPEED ONLY, OR COMPLETELY STOP OPERATING.
Consequence & remedy
Consequence: IF THE WINDSHIELD WIPERS STOP FUNCTIONING, THE DRIVER'S CLEAR FIELD OF VIEW MAY BE REDUCED INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL FURNISH THE PARTS AND LABOR REQUIRED TO IMPLEMENT THE DOGA-RECOMMENDED REMEDIES ON THE AFFECTED COACHES. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING JULY 2010. OWNERS MAY CONTACT MCI CUSTOMER SERVICE AT 1-800-241-2947.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA12007 · Mci Drive Shaft Safety Loop Failures
Opened Sep 13, 2012 · Closed Dec 3, 2015
Status: closed (inferred from source dates) · Power Train:driveline; Suspension:multiple Axle; SUSPENSION:REAR:AXLE:NON-POWERED Axle Assembly
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Additional source detail variants (3)
Power Train:driveline
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Suspension:multiple Axle
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
SUSPENSION:REAR:AXLE:NON-POWERED Axle Assembly
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Illustration