NHTSA owner reports · September 18, 2026 snapshot.
Official recalls
10Dec 10, 2025
Motor Coach Industries (MCI) is recalling certain 102DL3, 102D3, MC12PTV, E4500, D4000, 102D3ISTV, D4500, J4500, D4000ISTV, D4005, D4505, and J3500 transit buses. Please refer to MCI's recall report for specific model year information. The front door lower curb view glazing material is incorrect. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) number 205, "Glazing Materials."
Consequence & remedy
Consequence: The incorrect window glazing material may reduce the driver's visibility, increasing the risk of a crash.
Remedy: MCI will replace the glass, free of charge. Owner notification letters were mailed February 4, 2026. Owners may contact MCI customer service at 1-800-241-2947. MCI's number for this recall is 22-005.
Additional source detail variants (2)
Visibility:glass, Side/rear
Motor Coach Industries (MCI) is recalling certain 102DL3, 102D3, MC12PTV, E4500, D4000, 102D3ISTV, D4500, J4500, D4000ISTV, D4005, D4505, and J3500 transit buses. Please refer to MCI's recall report for specific model year information. The front door lower curb view glazing material is incorrect. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) number 205, "Glazing Materials."
Consequence: The incorrect window glazing material may reduce the driver's visibility, increasing the risk of a crash.
Remedy: MCI will replace the glass, free of charge. Owner notification letters were mailed February 4, 2026. Owners may contact MCI customer service at 1-800-241-2947. MCI's number for this recall is 22-005.
Structure:body:door
Motor Coach Industries (MCI) is recalling certain 102DL3, 102D3, MC12PTV, E4500, D4000, 102D3ISTV, D4500, J4500, D4000ISTV, D4005, D4505, and J3500 transit buses. Please refer to MCI's recall report for specific model year information. The front door lower curb view glazing material is incorrect. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) number 205, "Glazing Materials."
Consequence: The incorrect window glazing material may reduce the driver's visibility, increasing the risk of a crash.
Remedy: MCI will replace the glass, free of charge. Owner notification letters were mailed February 4, 2026. Owners may contact MCI customer service at 1-800-241-2947. MCI's number for this recall is 22-005.
Jan 20, 2016
Motor Coach Industries (MCI) is recalling certain model year 2011-2013 and 2015 J4500 coaches manufactured November 18, 2011, to July 10, 2015, 2011-2012 and 2014-2015 D4000 coaches manufactured manufactured September 24, 2010, to September 5, 2015, 2011-2013 and 2015-2016 D4005 coaches manufactured January 17, 2011, to November 23, 2015, 2012-2014 and 2016 D4000ISTV coaches manufactured July 18, 2012, to December 2, 2015, 2010-2016 D4500 coaches manufactured April 15, 2010, to December 18, 2015 and 2011-2016 D4505 coaches manufactured December 15, 2010, to December 4, 2015. The affected buses are equipped with certain Recaro Ergo-M Commercial Bus Driver Seats that have J-Brackets that may be missing welds which could allow the seat belt anchorage assembly to separate from the J-Bracket.
Consequence & remedy
Consequence: If the seatbelt anchorage assembly separates from the J-Bracket, the bus driver may not be properly restrained in the event of a crash increasing their risk of injury.
Remedy: MCI will notify owners and dealers will inspect the seats and determined if welds are missing. Any J-Bracket that is missing welds will be removed and replaced, free of charge. The recall began on February 15, 2016. Owners may contact MCI at 1-800-241-2947. MCI's number for this recall is SB 431.
Jun 16, 2014
Motor Coach Industries, Inc (MCI) is recalling certain model year 2009-2011 D4000 and D4500 and 2010 D4505 motor coaches equipped with LED lights interior lights powered by either a Vansco or IO multiplex system. Due to the excessive power draw of the LED lights, heat may build up at the fuse block and connector, causing the components to melt.
Consequence & remedy
Consequence: If this occurs, the surrounding material may be damaged and will burn, increasing the risk of a fire.
Remedy: MCI will notify owners, and dealers will replace the fuse holders, free of charge. The recall began in July 2014. Owners may contact MCI customer service at 1-847-285-2090. MCI's number for this recall is 388B. Note: This recall supersedes recall 12V-250. Motorcoaches that were remedied under the previous campaign need to be remedied under this campaign as well.
Additional source detail variants (2)
Interior Lighting
Motor Coach Industries, Inc (MCI) is recalling certain model year 2009-2011 D4000 and D4500 and 2010 D4505 motor coaches equipped with LED lights interior lights powered by either a Vansco or IO multiplex system. Due to the excessive power draw of the LED lights, heat may build up at the fuse block and connector, causing the components to melt.
Consequence: If this occurs, the surrounding material may be damaged and will burn, increasing the risk of a fire.
Remedy: MCI will notify owners, and dealers will replace the fuse holders, free of charge. The recall began in July 2014. Owners may contact MCI customer service at 1-847-285-2090. MCI's number for this recall is 388B. Note: This recall supersedes recall 12V-250. Motorcoaches that were remedied under the previous campaign need to be remedied under this campaign as well.
Electrical System:wiring:fuses And Circuit Breakers
Motor Coach Industries, Inc (MCI) is recalling certain model year 2009-2011 D4000 and D4500 and 2010 D4505 motor coaches equipped with LED lights interior lights powered by either a Vansco or IO multiplex system. Due to the excessive power draw of the LED lights, heat may build up at the fuse block and connector, causing the components to melt.
Consequence: If this occurs, the surrounding material may be damaged and will burn, increasing the risk of a fire.
Remedy: MCI will notify owners, and dealers will replace the fuse holders, free of charge. The recall began in July 2014. Owners may contact MCI customer service at 1-847-285-2090. MCI's number for this recall is 388B. Note: This recall supersedes recall 12V-250. Motorcoaches that were remedied under the previous campaign need to be remedied under this campaign as well.
Oct 17, 2013
Motor Coach Industries (MCI) is recalling certain model year 2000-2012 D, E, G and J series coaches manufactured January 2000 through June 2011 and equipped with Sure Power battery equalizers containing a particular epoxy sealing, aka 'potting', compound. The specific potting compound used in the subject products for insulation was found to be capable of conducting electricity after being exposed to heat.
Consequence & remedy
Consequence: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.
Remedy: MCI will notify owners, and Sure Power will replace the equalizers, free of charge. Owners may contact MCI at 1-847-285-2000. This campaign is MCI service bulletin 401.
May 31, 2012
MOTOR COACH INDUSTRIES, INC (MCI) IS RECALLING CERTAIN MODEL YEAR 2009-2011 D4000, D4500 AND 2010 D4505 MOTOR COACHES EQUIPPED WITH LED LIGHTS INTERIOR LIGHTS AND POWERED BY EITHER A VANSCO OR IO MULTIPLEX SYSTEM. DUE TO EXCESSIVE POWER DRAW OF THE LED LIGHTS, HEAT MAY BUILD UP AT THE FUSE BLOCK AND CONNECTOR, CAUSING COMPONENTS TO MELT.
Consequence & remedy
Consequence: IF THIS OCCURS, SURROUNDING MATERIAL MAY BE DAMAGED AND WILL BURN, INCREASING THE RISK OF A FIRE.
Remedy: MCI WILL NOTIFY OWNERS, AND DEALERS WILL INSTALL RE-DESIGNED WIRING, FREE OF CHARGE. THE RECALL BEGAN ON JULY 17, 2012. OWNERS MAY CONTACT MCI AT 1-866-624-2622.
Oct 26, 2011
MOTOR COACH INDUSTRIES (MCI) IS RECALLING CERTAIN MODEL YEAR 2003, AND 2007-2012 E AND J MODELS ALONG WITH MODEL YEAR 2007-2012 D4000, D4005, D4500, D4505, D4000ISTV MOTOR COACHES EQUIPPED WITH MERITOR WABCO ELECTRONIC STABILITY CONTROL (ESC) MODULES, MANUFACTURED FROM OCTOBER 2002, THROUGH OCTOBER 2011. UNDER CERTAIN ROAD AND DRIVING CONDITIONS, VEHICLE BODY ROLL AND ROAD INCLINATION CHARACTERISTICS MAY ADVERSELY AFFECT THE SLIP ANGLE CALCULATION OF THE ELECTRONIC STABILITY CONTROL (ESC) SYSTEM. THIS MIGHT CAUSE THE ESC TO PERCEIVE AN OVER STEERING SITUATION AND THEREFORE APPLY THE OUTER WHEEL BRAKE ON THE FRONT AXLE UNTIL THE VEHICLE IS PERCEIVED TO BE STABLE.
Consequence & remedy
Consequence: IF THE DRIVER IS SLOW TO REACT DURING THIS ESC INTERVENTION, THE VEHICLE MAY DEVIATE FROM THE INTENDED LINE OF TRAVEL, INCREASING THE RISK OF A CRASH.
Remedy: MCI WILL NOTIFY OWNERS AND REPLACE THE CONTROL MODULE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 4, 2012. OWNERS MAY CONTACT MCI CUSTOMER SERVICE AT 1-800-241-2947.
Jan 12, 2011
MCI IS RECALLING CERTAIN MODEL YEAR 2010-2011 D4500, D4505, AND D4000 MOTOR COACHES. THE AFFECTED PULLEY COVERS MAY LACK CERTAIN WELDS REQUIRED TO KEEP THE COVERS ATTACHED TO THE COACH STRUCTURE.
Consequence & remedy
Consequence: THE COVER WILL EVENTUALLY FAIL AS A RESULT OF FATIGUE, AND THE COVER MAY BECOME DETACHED FROM THE COACH AND FALL AND STRIKE A PERSON OR OBJECT, RESULTING IN PERSONAL INJURY OR PROPERTY DAMAGE.
Remedy: MCI WILL INSPECT AND REPLACE AS NECESSARY THE IDLER PULLEY COVERS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON FEBRUARY 10, 2011. OWNERS MAY CONTACT MCI CUSTOMER SERVICE AT 1-800-241-2947.
May 11, 2010
MCI IS RECALLING CERTAIN MODEL YEAR 2010 D4000, D4005, D4500, D4505, E4500, AND J4500 MODEL MOTOR COACHES MANUFACTURED FROM SEPTEMBER 2009 THROUGH MAY 2010, EQUIPPED WITH ARVINMERITOR FRONT AND TAG AXLE ASSEMBLIES. THE SUSPECT AXLES MAY HAVE HAD IMPROPER TORQUE APPLIED TO THE HUB/ROTOR/WHEEL ADAPTER BOLTS DURING THE ASSEMBLY PROCESS. REDUCED BOLT TORQUE COULD LEAD TO VIBRATION LOOSENING OF THE BOLT.
Consequence & remedy
Consequence: THIS COULD RESULT IN A LOSS OF THE WHEEL POSSIBLY RESULTING IN A CRASH.
Remedy: MCI WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE MOTOR COACHES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 28, 2010. OWNERS MAY CONTACT MCI AT 1-800-241-2947.
Mar 24, 2010
MCI HAS NOTIFIED NHTSA OF A DEFECT IN CERTAIN MODEL YEAR 2009 D4000 AND MODEL YEAR 2008-2010 D4500 AND D4505 MOTOR COACHES FITTED WITH RICON PUBLIC USE LIFTS. THE RESTRAINT BELT ON THESE LIFTS WAS DESIGNED TO PREVENT THE LIFT FROM MOVING, UNLESS THE TONGUE OF THE BELT IS FULLY ENGAGED AND LATCHED IN THE BUCKLE. RICON HAS DISCOVERED, HOWEVER, THAT IT IS POSSIBLE FOR THE OPERATOR TO INSERT THE BELT TONGUE INTO THE BUCKLE WITHOUT FULLY ENGAGING THE LATCHING MECHANISM. IN THIS CASE, THE RESTRAINT BELT WOULD APPEAR TO BE LATCHED, AND THE OPERATOR COULD RUN THE LIFT. IF THE RESTRAINT BELT TONGUE IS NOT FULLY ENGAGED INTO THE RESTRAINT BELT BUCKLE, AND LATCHED, THE LIFT MAY OPERATE WITH AN OCCUPANT ON THE PLATFORM.
Consequence & remedy
Consequence: THE USER OF THE LIFT COULD BE INJURED SHOULD THE LIFT MOVE WITHOUT THE RESTRAINT BELT PROPERLY BUCKLED.
Remedy: MCI IS WORKING WITH RICON AND RICON WILL BE HANDLING THE REMEDY FOR THIS CAMPAIGN. PLEASE SEE RICON'S DEFECT REPORT 09E-060. RICON WILL PROVIDE CUSTOMERS WITH A WARNING DECAL AND A DVD-BASED TRAINING AID. THE RECALL IS EXPECTED TO BEGIN DURING APRIL 2010. OWNERS MAY CONTACT RICON CUSTOMER SERVICE AT 1-800-322-2884, EMAILING AT WWW.DMATA@WABTEC.COM.
Mar 9, 2010
MCI IS RECALLING CERTAIN MODEL YEAR 2000-2009 D4000, MODEL YEAR 2001-2010 D4500 AND MODEL YEAR 2005-2007 D4505 COACHES EQUIPPED WITH RICON WHEELCHAIR LIFT (WCL) AND A CASSETTE-TYPE WCL COMPARTMENT DOOR. THE WHEELCHAIR LIFT MAY BECOME DISENGAGED FROM A LOCKED POSITION AND SLIDE UNRESTRAINED ON ITS ROLLERS IN THE STORAGE STRUCTURE, POTENTIALLY BREAKING THROUGH THE CASSETTE DOOR AND EXTENDING BEYOND THE OUTSIDE OF THE DOOR WHEN THE COACH IS IN MOTION, PARTICULARLY WHEN THE COACH IS MAKING A LEFT TURN.
Consequence & remedy
Consequence: IF THE COACH IS IN MOTION, POTENTIAL INJURY TO PERSONS AND/OR DAMAGE TO OTHER VEHICLES OR PROPERTY COULD OCCUR.
Remedy: MCI WILL PROVIDE PARTS AND LABOR TO INSTALL FREE OF CHARGE TO CUSTOMERS, A RICON DESIGNED RETROFIT KIT THAT INCLUDES A SPRING LOADED LOCK MECHANISM. THE SAFETY RECALL BEGAN ON MARCH 31, 2010. OWNERS MAY CONTACT MCI CUSTOMER SERVICE LINE AT 1-800-241-2947.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA12007 · Mci Drive Shaft Safety Loop Failures
Opened Sep 13, 2012 · Closed Dec 3, 2015
Status: closed (inferred from source dates) · Power Train:driveline; Suspension:multiple Axle; SUSPENSION:REAR:AXLE:NON-POWERED Axle Assembly
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Additional source detail variants (3)
Power Train:driveline
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Suspension:multiple Axle
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
SUSPENSION:REAR:AXLE:NON-POWERED Axle Assembly
In the fall of 2011, network contacts made ODI aware of four (4) incidents of drive shaft failure on the subject buses involving a loss of vehicle control.Two of the incidents were relatively low speed non-crash events; and two resulted in motor coach rollovers.All four events showed signs of a common failure mode.The incidents and crashes studied during this investigation all resulted from a series of complex events that began with the the yoke journal ears on the drive shafts fracturing.Once the drive shaft failed. it was not adequately contained by a drive shaft safety loop or structure.The spinning and unrestrained drive shaft caused severe damage to components on the steerable tag axle at the rear of the vehicle and created a forced steering condition.Once the rear of the bus was being forcibly steered by the tag axle, the driver lost control of the vehicle.These conclusions are based on the forensics evidence and testing conducted by the Vehicle Research and Test Center (VRTC).The VRTC test report is attached to this closing resume that provides details on how the test center was able to conclusively identify the defective components on the buses and demonstrate the sequence of events that caused the buses to crash.Prior to the drive shaft failure events, there were no indications of improper maintenance or that maintenance was required that would have prevented the incidents.Additionally, the U-joints on the incident vehicles were found to be in good working condition at the time of the failure. Finally, records of driver interviews indicated a sudden onset of the failure with no warning.Following the VRTC testing, MCI issued recall 14V-335 involving certain model year 1993-1995 102DL3 motor coaches manufactured November 1992 to January 1995, and 2006 and 2008 D4505 motor coaches manufactured June 2005 to April 2008.The affected buses are equipped with a drive shaft with a compressed length of 30 inches or less (allowing it to escape containment if it fails), a steerable trailing tag axle equipped with a system that changes the axle caster when the vehicle is in reverse travel and no electronic stability control (ESC).Recall 14V-335 addresses the concerns of this investigation.The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
PE12007 · Mci Driveshaft Safety Loop Failures
Opened Mar 21, 2012 · Closed Sep 20, 2012
Status: closed (inferred from source dates) · Power Train:driveline; Suspension:multiple Axle; SUSPENSION:REAR:AXLE:NON-POWERED Axle Assembly
ODI has identified certain MCI coaches with powertrain configurations that may allow a driveshaft separated at the rearward universal joint to escape the guardian structure of the steerable tag axle and damage steering and braking components.The damaged components may increase the risk of a loss of vehicle control. The subject coaches include 806 model year 1992 through 2012 MCI D and E series motor coaches with steerable tag axles.This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA12-007) to further study the alleged defect and to determine if a safety defect exists. The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Additional source detail variants (3)
Power Train:driveline
ODI has identified certain MCI coaches with powertrain configurations that may allow a driveshaft separated at the rearward universal joint to escape the guardian structure of the steerable tag axle and damage steering and braking components.The damaged components may increase the risk of a loss of vehicle control. The subject coaches include 806 model year 1992 through 2012 MCI D and E series motor coaches with steerable tag axles.This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA12-007) to further study the alleged defect and to determine if a safety defect exists. The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Suspension:multiple Axle
ODI has identified certain MCI coaches with powertrain configurations that may allow a driveshaft separated at the rearward universal joint to escape the guardian structure of the steerable tag axle and damage steering and braking components.The damaged components may increase the risk of a loss of vehicle control. The subject coaches include 806 model year 1992 through 2012 MCI D and E series motor coaches with steerable tag axles.This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA12-007) to further study the alleged defect and to determine if a safety defect exists. The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
SUSPENSION:REAR:AXLE:NON-POWERED Axle Assembly
ODI has identified certain MCI coaches with powertrain configurations that may allow a driveshaft separated at the rearward universal joint to escape the guardian structure of the steerable tag axle and damage steering and braking components.The damaged components may increase the risk of a loss of vehicle control. The subject coaches include 806 model year 1992 through 2012 MCI D and E series motor coaches with steerable tag axles.This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA12-007) to further study the alleged defect and to determine if a safety defect exists. The ODI report cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID: ODI Number 10447575.
Illustration