IllustrationTL* THE CONTACT OWNS A 2009 MAZDA MAZDA 5. WHILE ATTEMPTING TO ADD AIR TO THE REAR DRIVERS SIDE TIRE THE ALUMINUM VALVE STEM END BROKE DUE TO CORROSION. THE VEHICLE WAS TAKEN TO THE DEALER WHERE THE TECHNICIANS REPLACED THE VALVE STEM. THE VEHICLE WAS REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 23,000.
2009 Mazda MAZDA5
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Mazda MAZDA5 do not stand out strongly from the model-year median of 37.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA5 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
140–25K
1725–50K
650–75K
375–100K
7100–150K
2150K+
49 reports with mileage · 15 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports2 fire reports2 injury reports
Tires complaints
13 reportsVALVE STEM BROKE OFF WHILE LOW FILLING TIRE WITH AIR. EACH TIME THE TIRE LOOKED A LITTLE LOW AND WHEN AIR NOZZLE WAS USED IT BROKE OFF AND FLEW FORCEFULLY AND ALL THE AIR CAME SUDDENLY RUSHING OUT. THE COMPUTER LOW TIRE LIGHT WAS ON THE FIRST TIME THIS HAPPENED, THAT IS WHY I CHECKED THE PRESSURE. I HAD TO CALL SERVICE BO…
Read full complaint
VALVE STEM BROKE OFF WHILE LOW FILLING TIRE WITH AIR. EACH TIME THE TIRE LOOKED A LITTLE LOW AND WHEN AIR NOZZLE WAS USED IT BROKE OFF AND FLEW FORCEFULLY AND ALL THE AIR CAME SUDDENLY RUSHING OUT. THE COMPUTER LOW TIRE LIGHT WAS ON THE FIRST TIME THIS HAPPENED, THAT IS WHY I CHECKED THE PRESSURE. I HAD TO CALL SERVICE BOTH TIMES AND HAD THEM CHANGED TIRE AND REPLACE VALVE STEM WITH NON-COMPUTERIZED KIND. THEY DID NOT FIND ANY REASONS THAT THE TIRES HAD GONE LOW OTHER THAN THE VALVE STEM MAY HAVE BEEN ALREADY LEAKING. I THEN WENT TO DEALER TO GET NEW PARTS, WHICH WERE STILL UNDER WARRANTY, AND THEY SAID IT WAS FROM MISUSE AND WOULDN'T DO ANYTHING ABOUT IT. THEY WERE VERY RUDE. SAID IT WAS FROM HITTING CURB. IT WAS NOT. THE VALVE STEM IS WELL PROTECTED INSIDE THE RIM. THIS HAS HAPPENED TWICE WITHIN THE LAST SIX MONTHS. BOTH FAILURES WERE NEARLY IDENTICAL. I DID NOT REPORT THE FIRST TIME, BUT AFTER CHECKING AROUND I FOUND OUT THIS HAS HAPPENED TO OTHERS AND TIRE REPAIRMEN SAID THEY HAVE HAD TO CHANGE OUT SEVERAL. HAD I NOT SEEN THAT THE TIRE WAS A LITTLE LOW AND CHECKED IT IN MY GARAGE THIS COULD HAVE BEEN MUCH MORE DEVASTATING. I'M ALMOST AFRAID TO DRIVE IN CASE ONE OF THESE WOULD BREAK ON THE ROAD AND KILL ME. THE FAILURES HAPPENED IN DECEMBER 2010 AND APRIL 2011. THE VEHICLE I'M DRIVING IS A 2009. *TR
AT ABOUT 30,000 MILES, I NOTICED CONSIDERABLE VIBRATION AND A THUMPING NOISE, PARTICULARLY PROMINENT IN THE RIGHT FRONT QUADRANT. WHEN THE DEALERSHIP CHECKED THE PROBLEM IT WAS DIAGNOSED AS UNEVEN TIRE WEAR ON THE FRONT TIRES AND I PURCHASED TWO NEW TIRES AND HAD AN ALIGNMENT PERFORMED. THE PROBLEM RECURRED WITHIN 10,000 MILES…
Read full complaint
AT ABOUT 30,000 MILES, I NOTICED CONSIDERABLE VIBRATION AND A THUMPING NOISE, PARTICULARLY PROMINENT IN THE RIGHT FRONT QUADRANT. WHEN THE DEALERSHIP CHECKED THE PROBLEM IT WAS DIAGNOSED AS UNEVEN TIRE WEAR ON THE FRONT TIRES AND I PURCHASED TWO NEW TIRES AND HAD AN ALIGNMENT PERFORMED. THE PROBLEM RECURRED WITHIN 10,000 MILES, AFTER THE NEXT SERVICE. ONCE AGAIN THE DIAGNOSIS WAS UNEVEN TIRE WEAR, THIS TIME ON THE SET OF TIRES WHICH HAD NOT BEEN REPLACED. THE DEALER INDICATED THAT THEY NEEDED TO BE REPLACED AS THEY WERE A SAFETY RISK. ADDITIONALLY THE DEALER INDICATED THAT THE MAZDA 5 WAS HARD ON ITS REAR TIRES (FROM WHICH THESE HAD BEEN ROTATED AT THE LAST SERVICE). A QUICK REVIEW OF A VARIETY OF FORUMS WOULD INDICATE THAT THIS IS A PROBLEM THAT OTHERS HAVE EXPERIENCED AND THAT, IN ADDITION TO THE POOR QUALITY TOYO TIRES WHICH ARE ORIGINAL EQUIPMENT, WEAK ALLOY WHEELS MAY ALSO PLAY A ROLE. *TR
Official recalls
210V600000 · Fuel System, Other:delivery:fuel Pump
Nov 24, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA5 VEHICLES MANUFACTURED FROM JUNE 29, 2009, THROUGH APRIL 28, 2010. WATER MAY NOT HAVE BEEN REMOVED COMPLETELY FROM THE HARNESS CONNECTOR OF THE FUEL PUMP DUE TO VARIATIONS IN THE FUEL TANK LEAK CHECK PROCESS PERFORMED BEFORE VEHICLE ASSEMBLY. THE CONNECTOR PIN MAY CORRODE, POTENTIALLY CAUSING THE PIN TO BREAK.
Consequence & remedy
Consequence: THIS COULD LEAD TO AN INOPERATIVE FUEL PUMP, ENGINE STALL AND THE INABILITY TO RESTART THE ENGINE INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT THE FUEL PUMP CONNECTOR AND IF NECESSARY IT WILL BE REPLACED AND THE HARNESS WILL BE REPAIRED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 6, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.