IllustrationWhile driving car turns on its own almost causing accident
2009 Mazda MAZDA5
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Mazda MAZDA5 do not stand out strongly from the model-year median of 37.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA5 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
140–25K
1725–50K
650–75K
375–100K
7100–150K
2150K+
49 reports with mileage · 15 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports2 fire reports2 injury reports
What owners actually said
64 reportsThe headlights on this car are dangerously dim. Like the turn signals overpower them levels of dim. I’ve replaced the bulbs, the battery, cleaned all the connections, replaced the alternator, nothing makes a difference.
THIS MODEL OF MAZDA STEERING WHEEL STOP ROTATING MOSTLY ON HIGHWAY. AT TIME IT BECOME TOO STIFF TO OVE FOR 5 TO 10 MINUTES AND THEN IT COMES BACK ON IT IS WORRYING ME AS IT MAY CAUSE AN UNVOIDABLE CRASH.
Intermittently, the doors will not unlock when inside the vehicle, effectively trapping the occupants inside. Additionally, the locks will fail to lock or lock with either the key or the remote fob. trapping occupants inside or prohibiting someone on the outside from getting in to retrieve children inside.
TL* THE CONTACT OWNS A 2009 MAZDA 5. THE CONTACT STATED THAT THE VEHICLE WOULD NOT START. ON ONE OCCASION, THE VEHICLE BROKE DOWN IN THE MIDDLE OF A STREET AND WAS TOWED TO THE CONTACT'S HOME. THE CONTACT HAD A MECHANIC INSPECT THE VEHICLE WHO STATED THAT THE FUEL PUMP COULD BE THE CAUSE OF THE FAILURE. THE DEALER AND MANUFACTUR…
Read full complaint
TL* THE CONTACT OWNS A 2009 MAZDA 5. THE CONTACT STATED THAT THE VEHICLE WOULD NOT START. ON ONE OCCASION, THE VEHICLE BROKE DOWN IN THE MIDDLE OF A STREET AND WAS TOWED TO THE CONTACT'S HOME. THE CONTACT HAD A MECHANIC INSPECT THE VEHICLE WHO STATED THAT THE FUEL PUMP COULD BE THE CAUSE OF THE FAILURE. THE DEALER AND MANUFACTURER WERE NOT CONTACTED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS 163,000.
TL* THE CONTACT OWNS A 2009 MAZDA 5. WHILE DRIVING 55 MPH, THE POWER STEERING MALFUNCTIONED AND THE STEERING VEERED TO THE LEFT. THE FAILURE ALMOST CAUSED A CRASH. IN ADDITION, THE ENTIRE INSTRUMENT PANEL ILLUMINATED. THE CONTACT HAD TO EXERT EXCESSIVE FORCE TO TURN THE STEERING WHEEL AND PULL THE VEHICLE OFF THE ROAD. WHEN THE …
Read full complaint
TL* THE CONTACT OWNS A 2009 MAZDA 5. WHILE DRIVING 55 MPH, THE POWER STEERING MALFUNCTIONED AND THE STEERING VEERED TO THE LEFT. THE FAILURE ALMOST CAUSED A CRASH. IN ADDITION, THE ENTIRE INSTRUMENT PANEL ILLUMINATED. THE CONTACT HAD TO EXERT EXCESSIVE FORCE TO TURN THE STEERING WHEEL AND PULL THE VEHICLE OFF THE ROAD. WHEN THE VEHICLE WAS TURNED OFF AND RESTARTED, THE POWER STEERING RETURNED TO NORMAL AND THE CONTACT WAS ABLE TO DRIVE HOME. THE MANUFACTURER AND THE DEALER WERE NOT NOTIFIED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS 86,000.
CLIMATE CONTROL MALFUNCTIONING AND TURNING ON THE HEATER NOT AC
SLIDING PASSENGER DOOR WILL NOT LATCH. WILL OPEN WHILE DRIVING.
WHILE DRIVING THE CAR (APPROXIMATELY 35 MILES PER HOUR) THERE IS A SUDDEN LOSS OF POWER, INCLUDING LOSS OF POWER STEERING. CAR WOULD NOT RESTART. WE REPLACED ALTERNATOR AND HAD BATTERY CHECKED, WHICH WAS WORKING FINE WHEN THE SAME PROBLEM OCCURRED WHILE DRIVING ON HIGHWAY AT 45 MPH. PROBLEM IS RECURRING. CAR IS UNSAFE TO DR…
Read full complaint
WHILE DRIVING THE CAR (APPROXIMATELY 35 MILES PER HOUR) THERE IS A SUDDEN LOSS OF POWER, INCLUDING LOSS OF POWER STEERING. CAR WOULD NOT RESTART. WE REPLACED ALTERNATOR AND HAD BATTERY CHECKED, WHICH WAS WORKING FINE WHEN THE SAME PROBLEM OCCURRED WHILE DRIVING ON HIGHWAY AT 45 MPH. PROBLEM IS RECURRING. CAR IS UNSAFE TO DRIVE.
TL* THE CONTACT OWNS A 2009 MAZDA 5. WHILE THE CONTACT'S SON WAS DRIVING 45 MPH, THE DRIVER HEARD A GRINDING AND CLUNKING NOISE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE MOTOR MOUNTS FAILED AND SHIFTED THE ENGINE FORWARD, WHICH CAUSED THE CV JOINTS AND ENGINE HEAD TO FAIL. THE VEHICLE WAS …
Read full complaint
TL* THE CONTACT OWNS A 2009 MAZDA 5. WHILE THE CONTACT'S SON WAS DRIVING 45 MPH, THE DRIVER HEARD A GRINDING AND CLUNKING NOISE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE MOTOR MOUNTS FAILED AND SHIFTED THE ENGINE FORWARD, WHICH CAUSED THE CV JOINTS AND ENGINE HEAD TO FAIL. THE VEHICLE WAS NOT REPAIRED. A DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 150,000.
Official recalls
210V600000 · Fuel System, Other:delivery:fuel Pump
Nov 24, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA5 VEHICLES MANUFACTURED FROM JUNE 29, 2009, THROUGH APRIL 28, 2010. WATER MAY NOT HAVE BEEN REMOVED COMPLETELY FROM THE HARNESS CONNECTOR OF THE FUEL PUMP DUE TO VARIATIONS IN THE FUEL TANK LEAK CHECK PROCESS PERFORMED BEFORE VEHICLE ASSEMBLY. THE CONNECTOR PIN MAY CORRODE, POTENTIALLY CAUSING THE PIN TO BREAK.
Consequence & remedy
Consequence: THIS COULD LEAD TO AN INOPERATIVE FUEL PUMP, ENGINE STALL AND THE INABILITY TO RESTART THE ENGINE INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT THE FUEL PUMP CONNECTOR AND IF NECESSARY IT WILL BE REPLACED AND THE HARNESS WILL BE REPAIRED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 6, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.