IllustrationLOSS OF POWER STEERING TWO TIMES ON MY MAZDA 5. *TR
2008 Mazda MAZDA5
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2008 Mazda MAZDA5 do not stand out strongly from the model-year median of 37.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA5 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
240–25K
1525–50K
950–75K
375–100K
6100–150K
3150K+
60 reports with mileage · 7 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 37 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports1 fire reports2 injury reports
Steering complaints
37 reportsFIRST INCIDENT, POWER STEERING WAS LOST WHILE MAKING A U-TURN. WARNING LIGHT ILLUMINATED. REGAINED POWER AFTER HALF AN HOUR. SECOND INCIDENT, ATTEMPTED TO AVOID A SWERVING CAR, BUT STEERING WHEEL LOCKED UP AND COULD NOT CONTROL VEHICLE. ENDED UP SPINNING OUT AND CRASHED INTO ANOTHER CAR AND THE CENTER MEDIAN. *TR
POWER STEERING FAILED THREE TIMES YESTERDAY. DASH LIGHT CAME ON AND STEERING GOT VERY HEAVY ALTHOUGH I WAS ABLE TO MUSCLE THE CAR THROUGH TURNS. DAY WAS VERY HOT AND WE WERE DRIVING IN AN URBAN ENVIRONMENT. I DID WHAT THE OWNERS' MANUAL SAID - STOPPED AND SHUT OFF THE CAR, WAITED A FEW SECONDS AND RESTARTED THE CAR. IN TWO O…
Read full complaint
POWER STEERING FAILED THREE TIMES YESTERDAY. DASH LIGHT CAME ON AND STEERING GOT VERY HEAVY ALTHOUGH I WAS ABLE TO MUSCLE THE CAR THROUGH TURNS. DAY WAS VERY HOT AND WE WERE DRIVING IN AN URBAN ENVIRONMENT. I DID WHAT THE OWNERS' MANUAL SAID - STOPPED AND SHUT OFF THE CAR, WAITED A FEW SECONDS AND RESTARTED THE CAR. IN TWO OUT OF THE THREE INSTANCES THE POWER STEERING LIGHT HAD GONE OUT AND THE POWER STEERING WAS WORKING. IN THE OTHER INSTANCE THE LIGHT DID NOT GO OUT AND THE POWER ASSIST WAS NOT WORKING. THE CAR IS WORKING OKAY NOW AND I AM NOT SURE IF OR WHEN THIS MIGHT OCCUR AGAIN. BECAUSE OF THE DRIVING SITUATION AT THE TIME AND BECAUSE I AM AN EXPERIENCED DRIVER THIS DID NOT PRESENT A GRAVE SAFETY ISSUE; HOWEVER, HAD I BEEN DRIVING FASTER AND THE ROAD CONDITIONS BEEN POOR IT COULD HAVE BEEN CATASTROPHIC. *TR
MAZDA 3 AND 5 POWER STEERING FAILURE. THIS IS CURRENTLY COVERED BY MAZDA TSB: 06-002/09 I THINK MAZDA SHOULD ISSUE A RECALL FOR THE AFFECTED PARTS. LOSS OF POWER STEERING CAN BE VERY DANGEROUS FOR PEOPLE WITH LIMITED PHYSICAL STRENGTH. *TR
WHILE I WAS DRIVING MY 2008 MAZDA 5 IN LATE MARCH 2010, THE POWER STEERING STOPPED WORKING. THE PROBLEM PERSISTED UNTIL WE GOT IT FIXED. THE MECHANIC GAVE THE FOLLOWING DIAGNOSTIC, 'C1099 POWER STEERING CIRCUIT FAULT HYDROELECTRIC POWER STEERING PUMP INTERMITTENTLY SHUTS DOWN. MAZDA TSB REFERENCES THIS ISSUE. RECOMMEND PERF…
Read full complaint
WHILE I WAS DRIVING MY 2008 MAZDA 5 IN LATE MARCH 2010, THE POWER STEERING STOPPED WORKING. THE PROBLEM PERSISTED UNTIL WE GOT IT FIXED. THE MECHANIC GAVE THE FOLLOWING DIAGNOSTIC, 'C1099 POWER STEERING CIRCUIT FAULT HYDROELECTRIC POWER STEERING PUMP INTERMITTENTLY SHUTS DOWN. MAZDA TSB REFERENCES THIS ISSUE. RECOMMEND PERFORM TSB PER MAZDA AND REEVALUATE.' THE REPAIR COST AROUND $1,000. *TR
2008 MAZDA5 POWERSTEERING PUMP SHUTS DOWN WHEN HOT, MAZDA KNOWS ABOUT THE PROBLEM AND REFUSES TO RECALL. DANGEROUS FOR SMALL OR WEEK DRIVERS. HAS OCCURRED 2 TIMES ON ME IN AFTER SITTING IN TRAFFIC. INTERNET SEARCH REVEALS LOTS OF COMPLAINTS. *TR
POWER STEERING FAILURE AT LOW SPEED, POWER STEERING LIGHT COMES ON. AFTER RESTART FUNCTIONED NORMALLY. *TR
THE ENGINE ON MY MAZDA5 WAS RUNNING AT IDLE SPEED FOR APPROXIMATELY 10-15 MINUTES ON A WARM DAY. IN PULLING OUT OF THE PARKING LOT, THE POWER STEERING FAILED COMPLETELY AND THE WARNING LIGHT CAME ON. IN RESEARCHING WITH OTHER OWNERS, I REALIZED THAT THIS IS A PERVASIVE PROBLEM. *TR
TL*THE CONTACT OWNS A 2008 MAZDA 5. THE CONTACT STATED THAT ON MAY 7, 2010, THE POWER STEERING FAILED AND SHE HAD TO USE THE MANUAL STEERING POWER. THE VEHICLE WAS TAKEN TO A REPAIR SHOP WHERE THE CONTACT WAS INFORMED THAT THE POWER STEERING MODULE NEEDED TO BE REPLACED. THE VEHICLE HAD NOT BEEN REPAIRED AT THE TIME OF THE COMPL…
Read full complaint
TL*THE CONTACT OWNS A 2008 MAZDA 5. THE CONTACT STATED THAT ON MAY 7, 2010, THE POWER STEERING FAILED AND SHE HAD TO USE THE MANUAL STEERING POWER. THE VEHICLE WAS TAKEN TO A REPAIR SHOP WHERE THE CONTACT WAS INFORMED THAT THE POWER STEERING MODULE NEEDED TO BE REPLACED. THE VEHICLE HAD NOT BEEN REPAIRED AT THE TIME OF THE COMPLAINT. THE CONTACT CALLED THE DEALERSHIP AND WAS TOLD THAT THE VEHICLE WAS NO LONGER UNDER WARRANTY. THE FAILURE MILEAGE WAS APPROXIMATELY 39,000. THE CURRENT MILEAGE WAS APPROXIMATELY 41,000.
2008 MAZDA5 - 40K MILES AFTER IDLING IN PARKING LOT FOR APPROX 20 MINS, PUT CAR IN DRIVE AND ATTEMPTED TO LEAVE. POWER STEERING LIGHT ILLUMINATED, WIFE COULD NOT TURN WHEEL AT ALL. TURNED OFF CAR. I ARRIVED 10 MINS LATER AND WAS ABLE TO OPERATE THE STEERING WITH DIFFICULTY. *TR
Official recalls
110V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.