IllustrationI was driving my Mazda 5 2007 in traffic when suddenly it burst into flames on the passenger side underneath the hood
2007 Mazda MAZDA5
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2007 Mazda MAZDA5 do not stand out strongly from the model-year median of 37.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA5 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
120–25K
1025–50K
1050–75K
775–100K
13100–150K
1150K+
53 reports with mileage · 8 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 21 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 12 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
3 crash reports2 fire reports2 injury reports
Engine And Engine Cooling complaints
3 reportsWE PURCHASED OUR 2007, MAZDA 5 NEW IN JAN. 2007 FROM A LOCAL DEALERSHIP. AT A LITTLE OVER 9,000 MILES THE CAR BEGAN TO HESITATE AND WE RETURNED TO THE DEALERSHIP FOR THE FIRST SERVICE TO "FIX" THE PROBLEM. TO FAST FORWARD, HERE WE ARE DEC. 31ST, 2011 AND NOW WE ARE DEALING WITH NOT ONLY HESITATION AND STALLING, BUT NOW THE CAR …
Read full complaint
WE PURCHASED OUR 2007, MAZDA 5 NEW IN JAN. 2007 FROM A LOCAL DEALERSHIP. AT A LITTLE OVER 9,000 MILES THE CAR BEGAN TO HESITATE AND WE RETURNED TO THE DEALERSHIP FOR THE FIRST SERVICE TO "FIX" THE PROBLEM. TO FAST FORWARD, HERE WE ARE DEC. 31ST, 2011 AND NOW WE ARE DEALING WITH NOT ONLY HESITATION AND STALLING, BUT NOW THE CAR ACTUALLY "BUCKS" WHILE DRIVING IT ONLY ADDING TO THE DANGERS OF DRIVING IT. THIS IS A WELL DOCUMENTED PROBLEM AS WE HAVE CONTINUED TO RETURN IT THE SAME DEALERSHIP EACH TIME ONLY TO BE TOLD IT WAS "FIXED". THIS HAS BECOME A SAFETY CONCERN, AND A FINANCIAL WOE. WHY THE LACK OF CONCERN BY MAZDA AND OTHER AGENCIES THAT KNOW OF THIS PROBLEM BUT HAVE NOT MADE MAZDA ADMIT THE PROBLEM AND RECALL THESE CARS BEFORE SOMEONE IS KILLED. NOT EVERYONE IS IN THE POSITION TO JUST BUY ANOTHER CAR IF THEY SEEM TO HAVE A "LEMON". I WOULD REALLY LIKE TO KNOW MY RECOURSE IN ALL OF THIS....TO DRIVE A UNSAFE CAR?, TO HOPE I OR A FAMILY MEMBER WON'T BE HURT OF KILLED IN IT UNTIL SUCH TIME I CAN TRADE IT IN? AND THEN FEEL GUILTY THAT SOME OTHER PERSON IS PURCHASING MY UNSAFE CAR? I HOPE THAT THERE IS "SOME HOPE" BY CONTACTING YOUR AGENCY. IF NOTHING ELSE IF YOU WON'T HELP ME, MAYBE I CAN WARN SOMEONE ELSE ABOUT THIS CAR. *KB
I PURCHASED A 2007 MAZDA 5. THIS IS A DECENT CAR BUT AT COLDER TEMPERATURES THE VEHICLE WILL STALL AND SHUTTER ABOUT 1-3 MINUTES AFTER START UP. THE COLDER IT GETS AND THE MORE MILES THAT THE CAR GETS ON IT THE MORE OFTEN THIS OCCURS. THE DEALERSHIP TOLD ME THAT THIS IS A COMMON ISSUE AND THAT MAZDA HAS TOLD THEM TO FLASH AGAIN…
Read full complaint
I PURCHASED A 2007 MAZDA 5. THIS IS A DECENT CAR BUT AT COLDER TEMPERATURES THE VEHICLE WILL STALL AND SHUTTER ABOUT 1-3 MINUTES AFTER START UP. THE COLDER IT GETS AND THE MORE MILES THAT THE CAR GETS ON IT THE MORE OFTEN THIS OCCURS. THE DEALERSHIP TOLD ME THAT THIS IS A COMMON ISSUE AND THAT MAZDA HAS TOLD THEM TO FLASH AGAIN THE COMPUTER. THAT WAS DONE AND DID NOT FIX THE ISSUE. IT IS VERY DANGEROUS IF I PULL OUT IN TRAFFIC AND THIS VEHICLE FAILS I AM HAULING MYSELF AND MY HUSBAND AND 4 KIDS THAT IS GOING TO BE SOMETHING THAT IS MAZDA'S FAULT FOR NOT REMEDYING THE SITUATION. THIS NOW OCCURS AFTER DRIVING AND COMING TO A SLOW OR A STOP. ALSO WHEN THE TEMPERATURES ARE FROM 35-40 DEGREES THE FRONT RIGHT WHEEL MAKES AN AWFUL NOISE SOMETIMES SQUEAKING AND THEN SOMETIMES A GRINDING NOISE. THE DEALERSHIP INFORMED ME THAT IT IS "HEAVY, AND EXCESSIVE GREASE IN THE BALL JOINT". NOW THAT THE TEMPERATURE IS WARMER YOU CANNOT HEAR THIS ANYMORE. THE VEHICLE HAS 13,000 MILES AND WHILE DRIVING ON THE INTERSTATE AT 60-65 MPH AND YOU PUT ON THE BRAKES THE STEERING WHEEL SHAKES AND ACTS AS IF THE BRAKES ARE WARPED. WHEN THE TEMPERATURE IS HOT OUTSIDE THE A/C WORKS POORLY WITH A TEMP OUT OF THE VENTS AT 47 DEGREES. WHEN STOPPING AT A DRIVE THROUGH RESTURANT OR AT THE BANK THE SMELL OF BURNING ANTIFREEZE IS VERY NOTICABLE. THERE IS NO VISABLE LEAKS BUT THE SMELL OF ANTIFREEZE IS EVIDENT. THIS IS A POOR DESIGNED, OVERPRICED, NOT ADVERTISED VEHICLE THAT MAZDA SHOULD WORK OUT THE BUGS IN, OR GIVE THE MONEY BACK TO THE CUSTOMERS. THIS CAR HAS BEEN IN THE SHOP 7 TIMES SINCE NEW FOR THESE ISSUES THAT MAZDA SAID THEY DONT KNOW HOW TO FIX YET. I HAVE GIVEN THEM TIME AND THE OPPORTUNITY NOW MY LEMON LAW WILL BE RUNNING OUT AND I DONT WANT STUCK WITH A LEMON. *AK
Official recalls
110V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.