← New search

1979 Mack Wl

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all Wl years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

No component reports in this snapshot.

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

Limited mileage data: 0 of 0 reports include usable mileage. There isn’t enough coverage to show a useful chart.

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

NHTSA owner reports · September 18, 2026 snapshot.

0 crash reports0 fire reports0 injury reports

What owners actually said

0 reports

No matching complaints in this snapshot.

Official recalls

4

79V171000 · Suspension:rear:springs:leaf Spring Assembly

Jul 12, 1979

THE SPRING SEAT PLATE, LOCATED BETWEEN THE AXLE HOUSING AND THE SUSPENSION SPRINGS, MAY DEFORM DUE TO SPRING BENDING. AS A RESULT, THE CLAMPING FORCE IN THE ASSEMBLY MAY BE REDUCED. LOSS OF CLAMPING FORCE COULD CAUSE SPRING FAILURE AND THE AXLE WILL DISLOCATE. ALSO, THE TIRE COULD COME INTO CONTACT WITH THE SPRING.

Consequence & remedy

Consequence: Not supplied

Remedy: THE DEALER WILL REPLACE THE EXISTING SPRING SEAT WITH A NEWLY FABRICATED SEAT WHICH IS WELDED TO THE HOUSING. AN IMPROVED SPRING CLAMPING PLATE AND NEW SPRINGS WILL ALSO BE INSTALLED WITHOUT CHARGE.

79V164000 · Steering: Steering Wheel/handle Bar

Jul 9, 1979

THE FLANGE HEAD PINCH BOLTS USED IN THE YOKES OF THE STEERING SHAFT ASSEMBLIES MAY HAVE BEEN OVERSTRESSED DUE TO THE BOLTS NOT BEING TIGHTENED TO SPECIFICATIONS. AS A RESULT, THE PINCH BOLTS COULD BREAK WHILE IN SERVICE.

Consequence & remedy

Consequence: Not supplied

Remedy: FLANGE HEAD PINCH BOLTS WILL BE REPLACED WITH STANDARD GRADE 8 FASTENERS WITHOUT CHARGE TO OWNER.

79V137000 · Steering:linkages

Jun 1, 1979

THE PITMAN ARM RETAINING NUT MAY NOT HAVE BEEN TORQUED TO MANUFACTURER SPECIFICATIONS. THIS COULD RESULT IN INADEQUATE RETENTION OF THE NUT AT THE OUTPUT SHAFT, ALLOWING THE PITMAN ARM TO BECOME LOOSE.

Consequence & remedy

Consequence: Not supplied

Remedy: DEALER WILL INSPECT AND RETORQUE PITMAN ARM, IF NECESSARY, AT NO COST TO OWNER.

79V133000 · Engine And Engine Cooling:engine

May 31, 1979

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.

Consequence & remedy

Consequence: Not supplied

Remedy: DEALER WILL INSTALL A SHIELD FOR THE HEADS OF THE FOUR CAPSCREWS, ALONG WITH STRONGER SAE 8 GRADE 8 CAPSCREWS, IF NECESSARY, AT NO COST TO OWNER.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

0

No exact-year investigations in this snapshot.