NHTSA owner reports · September 18, 2026 snapshot.
Power Train complaints
174 reportsClear category filterMileage unknown · May 23, 2023
Power Train
The clutch on my jeep is acting up and there is a recall for it. But Jeep states they have no fix and are not able to tell me when they will come up with one. I feel they should just let aftermarket companies replace their defective clutches since they aren't really worried about the few folks with clutch issues. So currently I…
Read full complaint
The clutch on my jeep is acting up and there is a recall for it. But Jeep states they have no fix and are not able to tell me when they will come up with one. I feel they should just let aftermarket companies replace their defective clutches since they aren't really worried about the few folks with clutch issues. So currently I am driving a ticking timebomb. Once my transmission gets hot from the clutch it will cause a fire which Jeep is all aware of. This is a major safety issue. Imagine a car catching fire while driving on the highway. That would cause a massive pile up for sure.
NHTSA ODI #11523469
Mileage unknown · May 17, 2023
Power Train
Service Axle Locker System Keeps coming on and going off. Sometimes 4 times a min. Sometimes hours. Does not store or show any codes in the system when checked.
NHTSA ODI #11522441
Mileage unknown · May 16, 2023
Electrical SystemEnginePower Train
My wife was driving her Jeep to work this morning and a warning message came on the info screen stating the vehicle was shutting down soon and to safely pull over. She only had a two minute warning which was not enough time to pull over to a safe place without risking injury from being hit from another vehicle. The Jeep ended up…
Read full complaint
My wife was driving her Jeep to work this morning and a warning message came on the info screen stating the vehicle was shutting down soon and to safely pull over. She only had a two minute warning which was not enough time to pull over to a safe place without risking injury from being hit from another vehicle. The Jeep ended up and powered down within the two minutes of receiving the warning which caused loss of engine power, no power steering and no power brakes. This seems to be a pretty dangerous combination. It literally left her in the roadway. We had the batteries checked and they are ok. The vehicle did start back but the warning light came on again so it is parked until we can get it towed to the dealership. Researching it online it seems to be a common issue with the 2018 JLU. She currently has 117,000 miles on the Jeep.
NHTSA ODI #11522377
45,000 miles · May 15, 2023
Power Train
The contact owns a 2018 Jeep Wrangler. The contact received notification of NHTSA Campaign Number: 23V116000 (Power Train) however, the parts to do the recall repair were not yet available. The contact stated that while his daughter was driving at an undisclosed speed, she shifted into 3rd gear and the vehicle failed to respond.…
Read full complaint
The contact owns a 2018 Jeep Wrangler. The contact received notification of NHTSA Campaign Number: 23V116000 (Power Train) however, the parts to do the recall repair were not yet available. The contact stated that while his daughter was driving at an undisclosed speed, she shifted into 3rd gear and the vehicle failed to respond. The contact also stated that the vehicle failed to accelerate while in 6th gear. The contact then stated that he heard a loud screaming sound coming from under the hood of the vehicle. The vehicle was taken to the dealer where the vehicle remained. The vehicle was not diagnosed or repaired. Additionally, the contact stated that the automatic start warning light intermittently illuminated; however, when the failure occurred, the automatic start failed to operate and disengaged, preventing the rear-view camera from operating as designed. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure, but no further assistance was provided. The failure mileage was approximately 45,000. VIN tool confirms parts not available.
NHTSA ODI #11522136
Mileage unknown · May 15, 2023
Power Train
The contact owns a 2018 Jeep Wrangler. The contact received notification of NHTSA Campaign Number: 23V116000 (Power Train) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The m…
Read full complaint
The contact owns a 2018 Jeep Wrangler. The contact received notification of NHTSA Campaign Number: 23V116000 (Power Train) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
NHTSA ODI #11522074
Mileage unknown · Apr 21, 2023
Electrical SystemPower TrainSteering
I'll be driving the jeep it's a 2018 rubicon jl and all of a sudden all the dash lights come on and if I stop the vehicle the D on the shifter will keep flashing and the jeep.wont move have taken into same dealership 7 times and it's continues to do the same thing they've changed abs module cleaned off grounds checked all plugs …
Read full complaint
I'll be driving the jeep it's a 2018 rubicon jl and all of a sudden all the dash lights come on and if I stop the vehicle the D on the shifter will keep flashing and the jeep.wont move have taken into same dealership 7 times and it's continues to do the same thing they've changed abs module cleaned off grounds checked all plugs and connections and they keep saying it's fine. It's currently at the dealership for the same issue. It's been over a year of going to the dealership. Also one time.they told me it's ready came to pick it.up and it wouldn't go into drive.
NHTSA ODI #11518377
Mileage unknown · Apr 19, 2023
Power Train
I was constantly smelling a burning odor and my clutch started slipping. Took vehicle to dealer and they said clutch and flywheel needed to be replaced but there were none available, and they had to be manufactured and could take 2 to 3 months. Unsatisfactory! I left the dealership which is nextdoor to my place of employment …
Read full complaint
I was constantly smelling a burning odor and my clutch started slipping. Took vehicle to dealer and they said clutch and flywheel needed to be replaced but there were none available, and they had to be manufactured and could take 2 to 3 months. Unsatisfactory! I left the dealership which is nextdoor to my place of employment and completely lost the clutch on a busy road and had to be towed. I spent hours and days trying to find a clutch and finally located one and purchased it along with the flywheel. The repair seemed to be successful but now I am having that same burning smell. I received the recall notice 19A/NHTSA, however late, from FCA. It had the following statement: "WHAT IF I ALREADY PAID TO HAVE THIS REPAIR COMPLETED? If you have already experienced this specific condition and have paid to have it repaired, you may visit [XXX] to submit your reimbursement request online. Once we receive and verify the required documents, reimbursement will be sent to you within 60 days. If you have had previous repairs performed and/or already received reimbursement, you may still need to have the recall performed." I submitted my repair and proof of payment documents and they immediately closed my case because a remedy is not available. This makes no sense and contradicts the statement. Obviously I need to replace the clutch and flywheel. Now the replacement is putting off the same burning odor and I have to wait for a remedy knowing there is potential for a fire. I believe this has been an ongoing issue and should have been remedied long ago. Especially considering my vehicle is a 2018. There have been no warning indicators or lights. I drive my young grandsons around in this vehicle. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11517790
Mileage unknown · Apr 14, 2023
Power Train
The contact owns a 2018 Jeep Wrangler. The contact received notification of NHTSA Campaign Number: 23V116000 (Power Train) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issu…
Read full complaint
The contact owns a 2018 Jeep Wrangler. The contact received notification of NHTSA Campaign Number: 23V116000 (Power Train) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
NHTSA ODI #11517027
Mileage unknown · Mar 24, 2023
Power TrainSuspensionUnknown Or Other
At highway speeds when driving over surface imperfections, the jeep randomly and suddenly starts to wobble uncontrollably, with a significant wobble in the steering wheel. This wobbling goes away when the vehicle slows down, but pops up again in a random manner when driving over any surface imperfection / bump / road seam at hig…
Read full complaint
At highway speeds when driving over surface imperfections, the jeep randomly and suddenly starts to wobble uncontrollably, with a significant wobble in the steering wheel. This wobbling goes away when the vehicle slows down, but pops up again in a random manner when driving over any surface imperfection / bump / road seam at highway speeds
NHTSA ODI #11513657
Mileage unknown · Mar 12, 2023
Electrical SystemPower TrainSteering
Displays, "Service Shifter". Often followed by many, mostly random warnings, gauges fluctuate wildly, and disabled stop/start, traction and stability control; and sometimes loses power steering, and stalls and won't restart. The stereo volume, wipers, and cabin fan speed also can fluctuate wildly; worst case. This issue first ap…
Read full complaint
Displays, "Service Shifter". Often followed by many, mostly random warnings, gauges fluctuate wildly, and disabled stop/start, traction and stability control; and sometimes loses power steering, and stalls and won't restart. The stereo volume, wipers, and cabin fan speed also can fluctuate wildly; worst case. This issue first appeared after going through a puddle, and seems to be exacerbated by high EMF areas; this is only corollary. This vehicle has never been used roughly or off road. The obvious dangers are, spontaneous maniacal warnings are a significant distraction to driving; if stop/start is not disabled vehicle will not start after stop at intersection, causing disruption to traffic; if power steering randomly stops working, which occurs while stopped or driving, the vehicle is nearly impossible to drive, and can only practically be driven by a strongman athlete. The coup de grâce where everything goes berserk, is usually when parked and attempting to reset the condition. The problem has not been reproduced by a dealer or service center; I have spent days inspecting grounds, harnesses, and inspecting, cleaning and replacing connectors. There's also a long list of mostly random codes for nearly everything, including the persistent lost communication with TCM. Up to October 2022 and 66,000 miles the only warnings or codes were for, wheel sensor (rep under warrantee), and "Small Leak In Vapor Recovery System" (leaky gas cap). A month+ after the warrantee expired, at about 66,000 mi, the vehicle began to generate random warnings and codes, and became unbearable (and dangerous) to drive. My observations and inspections and limited testing (haven't probed system circuits directly) lead to an assertion that the problem is system wide; many wildly various, mostly non repeatable, codes are recorded, systems that shut down are wildly various and not always repeatable; like there's nothing specifically or consistently wrong-but everything is failing. 5V reg in TCM?
NHTSA ODI #11511450
Official recalls
14Sep 12, 2024
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
Remedy: Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.
Additional source detail variants (2)
Back Over Prevention: Sensing System: Camera
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
Remedy: Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.
Exterior Lighting:brake Lights
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
Remedy: Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.
Sep 5, 2024
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
Consequence & remedy
Consequence: An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
Remedy: Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.
Feb 23, 2023
Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Consequence & remedy
Consequence: Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Remedy: Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.
Jan 28, 2021
Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Consequence & remedy
Consequence: Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Remedy: FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.
Mar 3, 2020
Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Consequence & remedy
Consequence: The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.
Sep 26, 2019
Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.
Consequence & remedy
Consequence: A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.
Remedy: FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.
Apr 23, 2019
Erwin Hymer Group USA LP dba American Fastbacks (EHGUSA-AF) is recalling certain 2018 Jeep Wrangler vehicles sold with a roof top tent installed. The top cover of the roof top tent may crack or break, possibly resulting in the cover detaching from the vehicle while moving.
Consequence & remedy
Consequence: If the roof top tent cover detaches from the vehicle while moving, it can create a road hazard, increasing the risk of a crash.
Remedy: The remedy for this recall is still under development. The recall began May 9, 2019. Owners may contact American Fastbacks customer service at 1-844-533-7997 extension 301. Note: Vehicles in this recall are also included in recall 19V-190.
Nov 8, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler four-door vehicles. The right rear passenger door latch may not be in the correct location, possibly preventing the door from latching properly.
Consequence & remedy
Consequence: If the right rear passenger door opens unexpectedly, it can increase the risk of injury.
Remedy: Chrysler will notify owners, and dealers will repair the right rear door latch reinforcement, free of charge. The recall begin December 6, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UB6.
Sep 28, 2018
Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.
Consequence & remedy
Consequence: An unexpected reduction in steering ability, can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.
Aug 9, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.
Consequence & remedy
Consequence: A vehicle stall can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.
May 25, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The intermediate steering shaft may not have been properly welded causing a split where the external spline is formed.
Consequence & remedy
Consequence: If the weld seam splits, the steering wheel may lose center positioning causing a loss of steering responsiveness and increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect and, as necessary, replace the intermediate steering shaft, free of charge. The recall began June 21, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U48.
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
May 1, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Dodge Charger, Durango and Challenger, Jeep Grand Cherokee and Wrangler, Chrysler 300, and RAM 1500 vehicles. An incorrect transmission park lock rod may have been installed in the transmission.
Consequence & remedy
Consequence: If the incorrect park lock rod is installed, the transmission may not shift into 'PARK' and keep the vehicle from moving, increasing the risk of unintended vehicle movement and the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will install the correct park lock rod, free of charge. The recall began June 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U43.
Apr 12, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.
Consequence & remedy
Consequence: If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.
Remedy: Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.
Additional source detail variants (2)
Seats:mid/rear Assembly
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.
Consequence: If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.
Remedy: Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.
Structure:frame And Members
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.
Consequence: If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.
Remedy: Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE19012 · Frame Weld Deficiencies
Opened Sep 16, 2019 · Closed Oct 29, 2023
Status: closed (inferred from source dates) · Steering; Structure:frame And Members
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received information from the vehicle manufacturer Fiat Chrysler Automobiles (FCA) via information request letters dated March 8, 2019, and February 6, 2020. Supplemental requests for information occurred between July 2020 and July 2023. A review of the responsive manufacturer information showed that vehicles presenting an unexpected reduction in steering ability due to a welding tool misalignment were correctly addressed via recall 18V-675. General complaints concerning the weld appearance were not associated with a realized risk to motor vehicle safety. ODI identified a limited number of reports involving weld separation on vehicles that were out of scope of recall 18V-675. FCA identified various causes of weld quality issues in early production (build dates prior to March 2018) including improper welding techniques on galvanized frames and component part variation leading to off-seam welds. These issues were addressed in production for subject vehicles built after July 2018 and preceded a drop in weld failure reports. ODI reviewed manufacturer and agency reports of weld failures out of scope of recall 18V-675 and did not find any that resulted in a loss of vehicle control. There are no known crashes, injuries, or fatalities as a result of weld failures on vehicles not included in recall 18V-675. Due to the steering related consequence associated with Recall 18V-675, ODI opted to include a request for information regarding various steering issues experienced by vehicles included in this investigation. ODI reviewed manufacturer as well as agency data and determined these various steering issues were not related to any weld defect. Since the opening of this investigation, FCA has addressed the following steering concerns; a. Steering looseness due to material choice in the steering box internal components. FCA released an updated part with an internal component material less sensitive to temperature variances (TSB 08-003-21 REV. A).NHTSA will take further investigative action if justified. b. Steering wobble or shimmy due to a manufacturing and design deficiency in the steering damper. FCA released a part via Customer Satisfaction Notification (CSN) V41 in June 2019 which implemented supplier quality control improvements and design changes due to the presence of air in the base valve which degraded damping performance.NHTSA will take further investigative action if justified. c. Steering stiction, or loss of power steering, due to an underpowered steering pump calibration that occurred at highway speeds during cold weather. In December 2021, FCA released CSN Y95 which corrected this issue via software update. Due to the decreased number of consumer complaints, the service campaign appears to have addressed the issue related to an underpowered steering pump. NHTSA will take further investigative action if justified. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received information from the vehicle manufacturer Fiat Chrysler Automobiles (FCA) via information request letters dated March 8, 2019, and February 6, 2020. Supplemental requests for information occurred between July 2020 and July 2023. A review of the responsive manufacturer information showed that vehicles presenting an unexpected reduction in steering ability due to a welding tool misalignment were correctly addressed via recall 18V-675. General complaints concerning the weld appearance were not associated with a realized risk to motor vehicle safety. ODI identified a limited number of reports involving weld separation on vehicles that were out of scope of recall 18V-675. FCA identified various causes of weld quality issues in early production (build dates prior to March 2018) including improper welding techniques on galvanized frames and component part variation leading to off-seam welds. These issues were addressed in production for subject vehicles built after July 2018 and preceded a drop in weld failure reports. ODI reviewed manufacturer and agency reports of weld failures out of scope of recall 18V-675 and did not find any that resulted in a loss of vehicle control. There are no known crashes, injuries, or fatalities as a result of weld failures on vehicles not included in recall 18V-675. Due to the steering related consequence associated with Recall 18V-675, ODI opted to include a request for information regarding various steering issues experienced by vehicles included in this investigation. ODI reviewed manufacturer as well as agency data and determined these various steering issues were not related to any weld defect. Since the opening of this investigation, FCA has addressed the following steering concerns; a. Steering looseness due to material choice in the steering box internal components. FCA released an updated part with an internal component material less sensitive to temperature variances (TSB 08-003-21 REV. A).NHTSA will take further investigative action if justified. b. Steering wobble or shimmy due to a manufacturing and design deficiency in the steering damper. FCA released a part via Customer Satisfaction Notification (CSN) V41 in June 2019 which implemented supplier quality control improvements and design changes due to the presence of air in the base valve which degraded damping performance.NHTSA will take further investigative action if justified. c. Steering stiction, or loss of power steering, due to an underpowered steering pump calibration that occurred at highway speeds during cold weather. In December 2021, FCA released CSN Y95 which corrected this issue via software update. Due to the decreased number of consumer complaints, the service campaign appears to have addressed the issue related to an underpowered steering pump. NHTSA will take further investigative action if justified. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Structure:frame And Members
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received information from the vehicle manufacturer Fiat Chrysler Automobiles (FCA) via information request letters dated March 8, 2019, and February 6, 2020. Supplemental requests for information occurred between July 2020 and July 2023. A review of the responsive manufacturer information showed that vehicles presenting an unexpected reduction in steering ability due to a welding tool misalignment were correctly addressed via recall 18V-675. General complaints concerning the weld appearance were not associated with a realized risk to motor vehicle safety. ODI identified a limited number of reports involving weld separation on vehicles that were out of scope of recall 18V-675. FCA identified various causes of weld quality issues in early production (build dates prior to March 2018) including improper welding techniques on galvanized frames and component part variation leading to off-seam welds. These issues were addressed in production for subject vehicles built after July 2018 and preceded a drop in weld failure reports. ODI reviewed manufacturer and agency reports of weld failures out of scope of recall 18V-675 and did not find any that resulted in a loss of vehicle control. There are no known crashes, injuries, or fatalities as a result of weld failures on vehicles not included in recall 18V-675. Due to the steering related consequence associated with Recall 18V-675, ODI opted to include a request for information regarding various steering issues experienced by vehicles included in this investigation. ODI reviewed manufacturer as well as agency data and determined these various steering issues were not related to any weld defect. Since the opening of this investigation, FCA has addressed the following steering concerns; a. Steering looseness due to material choice in the steering box internal components. FCA released an updated part with an internal component material less sensitive to temperature variances (TSB 08-003-21 REV. A).NHTSA will take further investigative action if justified. b. Steering wobble or shimmy due to a manufacturing and design deficiency in the steering damper. FCA released a part via Customer Satisfaction Notification (CSN) V41 in June 2019 which implemented supplier quality control improvements and design changes due to the presence of air in the base valve which degraded damping performance.NHTSA will take further investigative action if justified. c. Steering stiction, or loss of power steering, due to an underpowered steering pump calibration that occurred at highway speeds during cold weather. In December 2021, FCA released CSN Y95 which corrected this issue via software update. Due to the decreased number of consumer complaints, the service campaign appears to have addressed the issue related to an underpowered steering pump. NHTSA will take further investigative action if justified. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE19008 · Seat Belt Buckle Bracket Failure
Opened Jul 29, 2019 · Closed Dec 12, 2019
Status: closed (inferred from source dates) · Seat Belts:front:buckle Assembly
On July 17, 2019, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 19-008 after receiving three Vehicle Owner Questionnaire (VOQ) reports alleging the driver's side seat belt buckle separated from the seat frame, rendering the seat belt non-functional. The VOQs involved model year (MY) 2015 and 2016 Jeep Wrangler (JK platform) that were configured for right-hand drive (RHD) use. On August 8, 2019, ODI issued an information request (IR) letter to FCA.The scope of the IR included all JK Wrangler produced for sale in the U.S. (both left- and right-hand drive), and amongst other things, requested any reports or allegations of driver's seat belt bracket failures on these vehicles. In its review of FCA's response, ODI determined that approximately 1.7 million JK Wrangler were produced from MY 2007 to 2018, about 16,000 of which were configured for RHD. ODI notes that the RHD Wrangler are typically used for rural postal delivery which often experience a more severe duty cycle. Also RHD JK was was not produced in MY 2007.As explained in the IR response, FCA identified three distinct populations of JK Wrangler concerning the driver's seat belt bucket bracket; specifically the MY 2007-2018 LHD (~1.7M units), the MY 2008-2010 RHD (4,563 units), and the MY 2011-2018 RHD (11,463 units) populations.FCA provided details on the designs used in each of these populations, identifying specific differences deemed pertinent to the strength and durability of each unique bracket design. FCA further reviewed its analysis of the complaint and warranty data identified under the IR, and noting that it had not identified any allegations of bracket failures on the LHD population, and only one allegation on the MY 2008-2010 RHD vehicles. By comparison, FCA identified 24 allegations of bracket failure for the MY 2011-2018 RHD JK, including two reports duplicative of the VOQs. Neither the FCA nor the VOQ reports allege an injury or fatality due to bracket failure. Based on this analysis, FCA decided to conduct a safety recall for the MY 2011-2018 RHD JK population. On September 30, 2019, FCA submitted a Defect Information Report initiating NHTSA Safety Recall 19V-680 (FCA No. VA6). Under the recall action, FCA will replace the driver's seat belt bracket on MY 2011-2018 RHD Jeep JK Wrangler. The repair will be conducted free of charge.In view of FCA's recall action, and its explanations of the scope of that action, ODI is closing PE19-008. ODI will continue to monitor the non-recalled RHD, and the LHD JK Wrangler for evidence of seat belt bracket failure and will take further action if warranted.The three VOQ reports cited above can be reviewed at NHTSA.gov under the following reference numbers:11190251, 11218472, 11231639.
EA19001 · Electrical Overstress
Opened Apr 19, 2019 · Closed Sep 19, 2024
Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
DP18004 · Frame Weld Deficiencies
Opened Nov 16, 2018 · Closed Sep 17, 2019
Status: closed (inferred from source dates) · Steering; Structure:frame And Members
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) opened a Defect Petition (DP18-004) to evaluate whether to grant or deny the petition. On March 8, 2019, ODI sent an Information Request letter to Fiat Chrysler Automobiles (FCA) requesting information on frame weld related issues on all MY 2018-2019 Jeep Wrangler 'JL' vehicles. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI opted to include a request for additional information concerning reports of steering shimmy or wobble, loose steering, and steering lockup in the March request letter. ODI has performed a preliminary analysis on the information obtained from FCA. Based on ODI's review of the applicable materials, NHTSA has decided to grant the petition. While reviewing the applicable materials obtained from the manufacturer, ODI identified various reports and references to frame welded component detachments that were outside of the scope of NHTSA Recall No. 18V-675. Additionally, the information that FCA provided did not adequately address whether frame weld quality deficiencies compromise the structural integrity of vehicles, and therefore may pose an unreasonable risk to motor vehicle safety. Finally, ODI needs to further evaluate the alleged steering-related defects reported through MY 2019 and the alleged defects' relation to weld quality.The petition was granted on September 16, 2019. Preliminary Evaluation PE19-012 has been opened to further assess the scope, frequency, and potential safety-related consequences of alleged weld quality deficiencies and steering related concerns on the MY 2018-2019 'JL' Jeep Wrangler vehicles.The ODI reports cited above can be viewed on NHTSA.gov under the following reference numbers:11234967, 11222390, 11219370, 11217080, 1204905, 11179954, 11171786, 11161243, 11155523, 11153044, 11143617, 11142722, 11142426, 11141336, 11141035, 11140637, 11140344, 11140262, 11140085, 11140057, 11139880, 11139866, 11139557, 11139467, 11139436, 11138974, 11138758, 11138757, 11132030, 11129738, 11129667, 11124312, 11120232, 11119676, 11119650, 11119454, 11119450, 11115658, 11115137, 11113029, 11112515, 11110583, 11109903, 11093172, 11088501, 11076098
Additional source detail variants (2)
Steering
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) opened a Defect Petition (DP18-004) to evaluate whether to grant or deny the petition. On March 8, 2019, ODI sent an Information Request letter to Fiat Chrysler Automobiles (FCA) requesting information on frame weld related issues on all MY 2018-2019 Jeep Wrangler 'JL' vehicles. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI opted to include a request for additional information concerning reports of steering shimmy or wobble, loose steering, and steering lockup in the March request letter. ODI has performed a preliminary analysis on the information obtained from FCA. Based on ODI's review of the applicable materials, NHTSA has decided to grant the petition. While reviewing the applicable materials obtained from the manufacturer, ODI identified various reports and references to frame welded component detachments that were outside of the scope of NHTSA Recall No. 18V-675. Additionally, the information that FCA provided did not adequately address whether frame weld quality deficiencies compromise the structural integrity of vehicles, and therefore may pose an unreasonable risk to motor vehicle safety. Finally, ODI needs to further evaluate the alleged steering-related defects reported through MY 2019 and the alleged defects' relation to weld quality.The petition was granted on September 16, 2019. Preliminary Evaluation PE19-012 has been opened to further assess the scope, frequency, and potential safety-related consequences of alleged weld quality deficiencies and steering related concerns on the MY 2018-2019 'JL' Jeep Wrangler vehicles.The ODI reports cited above can be viewed on NHTSA.gov under the following reference numbers:11234967, 11222390, 11219370, 11217080, 1204905, 11179954, 11171786, 11161243, 11155523, 11153044, 11143617, 11142722, 11142426, 11141336, 11141035, 11140637, 11140344, 11140262, 11140085, 11140057, 11139880, 11139866, 11139557, 11139467, 11139436, 11138974, 11138758, 11138757, 11132030, 11129738, 11129667, 11124312, 11120232, 11119676, 11119650, 11119454, 11119450, 11115658, 11115137, 11113029, 11112515, 11110583, 11109903, 11093172, 11088501, 11076098
Structure:frame And Members
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) opened a Defect Petition (DP18-004) to evaluate whether to grant or deny the petition. On March 8, 2019, ODI sent an Information Request letter to Fiat Chrysler Automobiles (FCA) requesting information on frame weld related issues on all MY 2018-2019 Jeep Wrangler 'JL' vehicles. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI opted to include a request for additional information concerning reports of steering shimmy or wobble, loose steering, and steering lockup in the March request letter. ODI has performed a preliminary analysis on the information obtained from FCA. Based on ODI's review of the applicable materials, NHTSA has decided to grant the petition. While reviewing the applicable materials obtained from the manufacturer, ODI identified various reports and references to frame welded component detachments that were outside of the scope of NHTSA Recall No. 18V-675. Additionally, the information that FCA provided did not adequately address whether frame weld quality deficiencies compromise the structural integrity of vehicles, and therefore may pose an unreasonable risk to motor vehicle safety. Finally, ODI needs to further evaluate the alleged steering-related defects reported through MY 2019 and the alleged defects' relation to weld quality.The petition was granted on September 16, 2019. Preliminary Evaluation PE19-012 has been opened to further assess the scope, frequency, and potential safety-related consequences of alleged weld quality deficiencies and steering related concerns on the MY 2018-2019 'JL' Jeep Wrangler vehicles.The ODI reports cited above can be viewed on NHTSA.gov under the following reference numbers:11234967, 11222390, 11219370, 11217080, 1204905, 11179954, 11171786, 11161243, 11155523, 11153044, 11143617, 11142722, 11142426, 11141336, 11141035, 11140637, 11140344, 11140262, 11140085, 11140057, 11139880, 11139866, 11139557, 11139467, 11139436, 11138974, 11138758, 11138757, 11132030, 11129738, 11129667, 11124312, 11120232, 11119676, 11119650, 11119454, 11119450, 11115658, 11115137, 11113029, 11112515, 11110583, 11109903, 11093172, 11088501, 11076098
Illustration