A SLIT, ABOUT 1" LONG, APPEARED IN THE CONVERTIBLE TOP REAR QUARTERPANEL. YESTERDAY, I NOTICED ON THE OTHER SIDE OF THE CAR, IN THE EXACT SAME SPOT, AN INDENTATION, ABOUT TO BECOME ANOTHER SLIT. HONDA DEALER AND CUSTOMER COMPLAINT BOTH NOTIFIED. THEY HAVE NOTHING ON FILE ABOUT THIS ISSUE AND OFFERED NO SOLUTIONS. THERE OBVIOUSLY…
Read full complaint
A SLIT, ABOUT 1" LONG, APPEARED IN THE CONVERTIBLE TOP REAR QUARTERPANEL. YESTERDAY, I NOTICED ON THE OTHER SIDE OF THE CAR, IN THE EXACT SAME SPOT, AN INDENTATION, ABOUT TO BECOME ANOTHER SLIT. HONDA DEALER AND CUSTOMER COMPLAINT BOTH NOTIFIED. THEY HAVE NOTHING ON FILE ABOUT THIS ISSUE AND OFFERED NO SOLUTIONS. THERE OBVIOUSLY IS AN ISSUE WITH THE RETRACTION MECHANISM DESIGN OR FUNCTION. WEAR ON A RETRACTED CONVERTIBLE TOP , TO THE POINT OF PENETRATION, IS UNACCEPTABLE. *TR
NHTSA ODI #10525827
21,000 miles · Jun 28, 2010
Structure
THE CONVERTIBLE TOP ON MY HONDA S2000 HAS RIPPED FOR THE SECOND TIME. THE FIRST TIME THE TOP WAS REPLACED UNDER WARRANTY. UNDER INDEPENDENT EXAMINATION THE TOP WAS FOUND TO HAVE AN ENGINEERING DEFECT WHERE THE FABRIC TOP RUBS AGAINST A SHARP METAL COMPONENT OF THE TOP FRAME CAUSING A TEAR. *TR
NHTSA ODI #10340502
16,000 miles · Jul 13, 2009
Structure
TL*THE CONTACT OWNS A 2006 HONDA S2000. THE CONTACT STATED THAT THE METAL LINK ON THE CONVERTIBLE TOP WAS PLACED DIRECTLY OVER HIS SKULL. IN THE EVENT OF A CRASH, HIS HEAD WOULD STRIKE THE METAL LINK AND CAUSE INJURIES. THE MANUFACTURER ADVISED THE CONTACT TO TAKE THE VEHICLE TO THE DEALER TO CHECK IF THE ISSUE WAS DUE TO A M…
Read full complaint
TL*THE CONTACT OWNS A 2006 HONDA S2000. THE CONTACT STATED THAT THE METAL LINK ON THE CONVERTIBLE TOP WAS PLACED DIRECTLY OVER HIS SKULL. IN THE EVENT OF A CRASH, HIS HEAD WOULD STRIKE THE METAL LINK AND CAUSE INJURIES. THE MANUFACTURER ADVISED THE CONTACT TO TAKE THE VEHICLE TO THE DEALER TO CHECK IF THE ISSUE WAS DUE TO A MANUFACTURER DEFECT. THE CONTACT FEELS THAT THIS IS A SAFETY HAZARD AND WANTS THE MANUFACTURER TO PROVIDE A HARD TOP. THE CURRENT AND FAILURE MILEAGES WERE 16,000. THE CONVERTIBLE TOP HAS A PROTRUDING METAL JOINT AND OTHER UNSHIELDED METAL PIECES. UPDATED 07/21/09.*JB
American Honda Motor Co., Inc. (Honda) is recalling certain model year 2006 Acura RSX vehicles manufactured January 18, 2006, through August 12, 2006; and model year 2006-2007 Honda S2000 vehicles manufactured January 19, 2006, through November 13, 2006. The brake booster may be unable to maintain a vacuum when the brake pedal is depressed, decreasing brake assist.
Consequence & remedy
Consequence: With reduced braking assistance, the vehicle may require additional brake pedal force to prevent a lengthened stopping distance, increasing the risk of a crash.
Remedy: Honda will notify owners, and dealers will inspect the brake booster assembly. If necessary, the dealers will replace the booster assembly free of charge. The recall is expected to begin during July 2013. Owners may contact Honda at 1-310-783-2000. Honda's recall number is JA4. Acura's recall number is JA5.
ON CERTAIN PASSENGER VEHICLES AND MOTORCYCLES, THE OWNER'S MANUALS CONTAIN INCORRECT CONTACT INFORMATION FOR THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S (NHTSA) VEHICLE SAFETY HOTLINE.
Consequence & remedy
Consequence: THE LANGUAGE IN THE OWNER'S MANUALS IS NOT IN ACCORDANCE WITH THE CURRENT MANDATORY REQUIREMENTS.
Remedy: HONDA WILL SEND A POSTCARD TO DEALERS AND OWNERS WITH THE CORRECT NHTSA VEHICLE SAFETY HOTLINE INFORMATION AND WITH INSTRUCTIONS TO INSERT THE CARD INTO THE "REPORTING SAFETY DEFECTS" SECTION OF THE OWNER'S MANUAL. THE RECALL BEGAN ON AUGUST 2, 2006. OWNERS MAY CONTACT HONDA AT 1-800-999-1009, ACURA AT 1-800-382-2238 OR HONDA MOTORCYCLES AT 1-866-784-1870.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
0
No exact-year investigations in this snapshot.
2006 Honda S2000 Problems, Complaints & Recalls | Skip That Year
Illustration