CHRONOLOGY OF CASCADING VEHICLE SAFETY FAILURES VIN [XXX] Vehicle 2015 Honda CR-V. 1 STRUCTURAL BODY FRAME DEFECT. Vehicle has a chronic upper body structural alignment defect allowing massive water intrusion to bypass factory headliner and moonroof seals. Multiple consecutive factory OEM headliners have been destroyed by water…
Read full complaint
CHRONOLOGY OF CASCADING VEHICLE SAFETY FAILURES VIN [XXX] Vehicle 2015 Honda CR-V. 1 STRUCTURAL BODY FRAME DEFECT. Vehicle has a chronic upper body structural alignment defect allowing massive water intrusion to bypass factory headliner and moonroof seals. Multiple consecutive factory OEM headliners have been destroyed by water logging, proving the upper tracking architecture is permanently warped and cannot maintain an environmental seal. 2 ELECTRICAL FAILURE ENGINE STALL HAZARD. Saturated water tracking through the upper frame has migrated into primary engine bay electrical lines. This chronic moisture caused a severe short circuit that fried the vehicle alternator, voltage regulator, and primary battery requiring emergency replacement. This infrastructure breakdown creates an imminent safety risk of sudden loss of vehicle charging power and dangerous engine stalling while operating at highway speeds. 3 ADAS INFRASTRUCTURE FAILURES. Moisture migration has breached the primary dashboard wire harnesses causing active continuous power dropouts and glitching across the center infotainment screen and main driver instrument display interface, blinding the operator to speedometers and critical crash avoidance alerts. 4 AIRBAG HAZARDS ACTIVE BIOHAZARD. Saturated water tracking down internal pillars runs directly over Side Curtain Airbag modules and electronic connectors, risking sensor corrosion. Cabin flooding has saturated seating foam, endangering electronic Occupant Classification Sensors OCS that regulate passenger airbag deployment forces. Unremediated moisture left toxic mold spores festering beneath the seating infrastructure, causing severe respiratory irritation to occupants. REPAIR STATUS. Unresolved safety defect. Repair networks failed to remediate structural hazards. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11740946
Mileage unknown · Nov 21, 2025
Structure
Vehicle unlocks if you approach it, all doors unlock without using the keyfob or putting your hand into the drivers or front passengers door handle. This happens with both keyfobs. Fresh batteries are in both keyfobs.
NHTSA ODI #11700896
Mileage unknown · May 29, 2025
Structure
MY BATTERY KEEPS RUNNING DOWN, EVEN AFTER I HAD IT REPLACED BY AAA. TOOK IT TO KINGSPORT HONDA AND HAD IT CHECKED OUT. THEY SAID IT WAS THE DRIVER SIDE DOOR HANDLE THAT WAS DRAWING DOWN THE BATTERY. THEY ALREADY KNEW WHAT THE PROBLEM WAS, BUT TO MAKE SURE THEY PUT A METER ON IT. THE HANDEL HAS GOTTEN SO HOT IT HAS VISIBALY DAM…
Read full complaint
MY BATTERY KEEPS RUNNING DOWN, EVEN AFTER I HAD IT REPLACED BY AAA. TOOK IT TO KINGSPORT HONDA AND HAD IT CHECKED OUT. THEY SAID IT WAS THE DRIVER SIDE DOOR HANDLE THAT WAS DRAWING DOWN THE BATTERY. THEY ALREADY KNEW WHAT THE PROBLEM WAS, BUT TO MAKE SURE THEY PUT A METER ON IT. THE HANDEL HAS GOTTEN SO HOT IT HAS VISIBALY DAMAGED THE INSIDE DOOR PANEL. THEY ONLY WANT 795.00 TO REPLACE THE HANDLE. SOUNDS LIKE A MANUFACTURING PROBLEM. THIS IS VERY UNSAFE
NHTSA ODI #11663829
Mileage unknown · Dec 27, 2024
Structure
Paint is starting to peel from the lower edge of the upper sill of the lift gate.
NHTSA ODI #11632778
Mileage unknown · Jan 15, 2024
Structure
UNKNOWN
NHTSA ODI #11565517
68,000 miles · Oct 6, 2023
Structure
The contact owns a 2015 Honda CR-V. The contact stated that while driving at an undisclosed speed, the sun visor failed to stay secured, potentially obstructing visibility. The vehicle was taken to the dealer, who determined that the visor would need to be replaced. The manufacturer was not notified of the failure. The failure m…
Read full complaint
The contact owns a 2015 Honda CR-V. The contact stated that while driving at an undisclosed speed, the sun visor failed to stay secured, potentially obstructing visibility. The vehicle was taken to the dealer, who determined that the visor would need to be replaced. The manufacturer was not notified of the failure. The failure mileage was 68,000.
NHTSA ODI #11548720
30,100 miles · May 20, 2022
SeatsSteeringStructure
The contact owns a 2015 Honda CR-V. The contact stated that while the vehicle was either idle or while driving at various speeds, the steering wheel, seats, and dashboard all would sporadically start to vibrate. There were no warning lights illuminated. The vehicle was then taken to the dealer who advised him that they did not r…
Read full complaint
The contact owns a 2015 Honda CR-V. The contact stated that while the vehicle was either idle or while driving at various speeds, the steering wheel, seats, and dashboard all would sporadically start to vibrate. There were no warning lights illuminated. The vehicle was then taken to the dealer who advised him that they did not recognize the failure. The vehicle was not repaired. The contact stated that while conducting his own research, he found there were many complaints about what he was experiencing with his vehicle. The manufacturer was notified about the failure and advised that he contact the NHTSA for assistance. The failure mileage was approximately 30,100.
NHTSA ODI #11465522
Mileage unknown · Apr 5, 2022
StructureUnknown Or Other
While driving during clear weather and around no highway overpasses, the sunroof on our Honda CRV spontaneously shattered. No evidence of an object or projectile were found.
NHTSA ODI #11459732
19,672 miles · Aug 1, 2020
Structure
DOOR LOCK ACTUATOR FOR THE PASSENGER SIDE REAR DOOR BINDS WHICH MAKES IT DIFFICULT TO MANUALLY UNLOCK THE DOOR FROM THE INSIDE. THIS IS AN ONGOING PROBLEM. IT WAS REPORTED TO SCOTT ROBINSON HONDA IN ON 8/15/15 AND AGAIN ON 3/4/2016. THEY REFUSED TO ACKNOWLEDGE THE PROBLEM CLAIMING THEY COULD NOT DUPLICATE IT. THE VEHICLE WAS…
Read full complaint
DOOR LOCK ACTUATOR FOR THE PASSENGER SIDE REAR DOOR BINDS WHICH MAKES IT DIFFICULT TO MANUALLY UNLOCK THE DOOR FROM THE INSIDE. THIS IS AN ONGOING PROBLEM. IT WAS REPORTED TO SCOTT ROBINSON HONDA IN ON 8/15/15 AND AGAIN ON 3/4/2016. THEY REFUSED TO ACKNOWLEDGE THE PROBLEM CLAIMING THEY COULD NOT DUPLICATE IT. THE VEHICLE WAS TAKEN TO DCH HONDA ON 7/16/20, THE PROBLEM WAS ACKNOWLEDGED BY THEM. A CLAIM WAS SET UP WITH HONDA CUSTOMER SERVICE, CLAIM NUMBER 11441768. HONDA IS NOW REFUSING TO PAY. THIS IS A SAFETY ISSUE AS A PASSENGER SITTING IN THE BACK MAY NOT BE ABLE TO MANUALLY UNLOCK THE DOOR IN ORDER TO EXIT THE VEHICLE.
NHTSA ODI #11342634
14,000 miles · Aug 2, 2019
StructureVehicle Speed ControlCrash
HAS THERE BEEN ANY PROBLEMS WITH ACCELERATION ON HONDA CRV ESPECIALLY 2015. I RECENTLY HAD A PROBLEM WITH MINE. WHILE PARKING IN A SPACE, THE GAS PEDAL TOOK OFF AND I RAN INTO A ANOTHER PARKED CAR.
Honda (American Honda Motor Co.) is recalling certain 2013-2023 Honda Accord, Civic Coupe, Civic Sedan, Civic Hatchback, Civic Type R, CR-V, HR-V, Ridgeline, Odyssey, Acura ILX, MDX, MDX Hybrid, RDX, RLX, TLX, 2019-2022 Honda Insight, Passport, 2020 Honda CR-V Hybrid, 2018-2019 Honda Clarity PHEV, Fit, and 2015-2020 Honda Accord Hybrid, Pilot, Acura NSX vehicles. The fuel pump inside the fuel tank may fail.
Consequence & remedy
Consequence: Fuel pump failure can cause an engine stall while driving, increasing the risk of a crash.
Remedy: Dealers will replace the fuel pump module, free of charge. Owner letters were mailed September 6, 2024. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are KGC and KGD. This recall is an expansion of NHTSA recall numbers 21V-215 and 20V-314.
Honda (American Honda Motor Co.) is recalling certain 2015-2016 Honda CR-V vehicles that recently received a replacement engine. The replacement engine may have been built with the wrong pistons, potentially affecting the engine's performance.
Consequence & remedy
Consequence: The reduced performance may result in an engine stall, increasing the risk of a crash.
Remedy: Honda will notify owners, and dealers will inspect the engines and replace the incorrect components, as necessary, free of charge. The recall began June 20, 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's number for this recall is KF6.
American Honda Motor Co. (Honda) is recalling certain model year 2014 Accord L4 vehicles manufactured July 29, 2014, to July 31, 2014, 2015 Accord L4 vehicles manufactured August 14, 2014, to January 30, 2015, and 2015 CR-V vehicles manufactured September 9, 2014, to February 6, 2015. The affected vehicles may have been assembled with improperly torqued connecting rod bolts, which can cause the engine to lose power or leak oil.
Consequence & remedy
Consequence: Loss of engine power may result in a vehicle stall, increasing the risk of a crash. If the engine leaks oil in the proximity of hot engine or exhaust components, there is an increased risk of a fire.
Remedy: Honda will notify owners, and dealers will replace the engine short block, free of charge. The recall began on March 27, 2015. Owners may contact Honda customer service at 1-888-234-2138. Honda's number for this recall is JP2 (for Accord models) and JP3 (for CR-V models).
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA19001 · Electrical Overstress
Opened Apr 19, 2019 · Closed Sep 19, 2024
Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
Illustration