IllustrationTHERE IS A CRACK IN MY DASHBOARD THAT COULD SERIOUS INJURY OR DEATH IF THE AIRBAGS DEPLOY.
2013 GMC Yukon Xl
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2013 GMC Yukon Xl do not stand out strongly from the model-year median of 68.
About this comparison →How this year compares
Owner complaints by model year
Compare all Yukon Xl years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 17 of 22 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Structure. Review the 10 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports0 fire reports0 injury reports
Structure complaints
10 reportsTL* THE CONTACT OWNS A 2013 GMC YUKON XL. THE CONTACT STATED THAT THE DASHBOARD WAS CRACKED ON THE FRONT DRIVER'S SIDE. THE FAILURE OCCURRED WITHOUT WARNING. THE CONTACT CALLED AND TOOK THE VEHICLE TO COUNTRYSIDE CHEVROLET BUICK GMC (N8167 KELLOM RD, BEAVER DAM, WI 53916, 920-354-6097) WHERE THE TECHNICIAN TOOK PICTURES OF THE F…
Read full complaint
TL* THE CONTACT OWNS A 2013 GMC YUKON XL. THE CONTACT STATED THAT THE DASHBOARD WAS CRACKED ON THE FRONT DRIVER'S SIDE. THE FAILURE OCCURRED WITHOUT WARNING. THE CONTACT CALLED AND TOOK THE VEHICLE TO COUNTRYSIDE CHEVROLET BUICK GMC (N8167 KELLOM RD, BEAVER DAM, WI 53916, 920-354-6097) WHERE THE TECHNICIAN TOOK PICTURES OF THE FAILURE AND STATED THAT THE DASHBOARD NEEDED TO BE REPLACED AT THE OWNER'S EXPENSE. THE MANUFACTURER STATED THAT THERE WAS NO RECALL AND THE VEHICLE WAS OUT OF WARRANTY. THE MANUFACTURER REFERRED THE CONTACT TO NHTSA. THE FAILURE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 82,000.
DEFECT CAUSED DASH TO CRACK AT THE PASSANGER AIRBAG, I AM CONCERNED ABOUT MY CHILDREN BEING INJURED FROM THE CRACKED DASH AS WELL AS THE SHARDS FLYING AND INJURING MY CHILD IF I WERE TO BE IN AN ACCIDENT.
THE DASH BOARD NEAR THE STEERING COLUMN JUST CRACKED AS WELL AS THE INTERIOR DRIVERSIDE FRONT DOOR. BOTH PIECES APPEAR TO BE CHEAP PLASTIC. I HAVE RECEIVED A QUOTE FOR $1600 TO FIX THE DOOR AND $1000 TO FIX THE DASH WHEN THESE ARE BOTH DEFECT FROM GM.
I PREVIOUSLY OWNED A 2009 CHEVROLET TAHOE. WE BOUGHT IT WITH 45K MILES. ABOUT 60K MILES THE DASH BEGAN TO CRACK ABOVE THE SPEEDOMETER AND NEXT TO THE PASSENGER AIR BAG. I PAID A BODY SHOP TO REPLACE THE DASH AND THEN EVERYTHING WAS FINE. AFTER 130K MILES, THE CRACK ABOVE THE SPEEDOMETER BECAME VISIBLE. WE THEN TRADED IT IN AND N…
Read full complaint
I PREVIOUSLY OWNED A 2009 CHEVROLET TAHOE. WE BOUGHT IT WITH 45K MILES. ABOUT 60K MILES THE DASH BEGAN TO CRACK ABOVE THE SPEEDOMETER AND NEXT TO THE PASSENGER AIR BAG. I PAID A BODY SHOP TO REPLACE THE DASH AND THEN EVERYTHING WAS FINE. AFTER 130K MILES, THE CRACK ABOVE THE SPEEDOMETER BECAME VISIBLE. WE THEN TRADED IT IN AND NOW OWN A 2013 YUKON XL. I BOUGHT IT USED, UNDER WARRANTY AND IT NOW IT IS OUT OF WARRANTY WITH 55K MILES. OVER THE LAST 10K MILES, I HAVE SEEN MY DASH CRACK ABOVE THE SPEEDOMETER AND NEXT TO THE PASSENGER AIR BAG. THE SAME LOCATION AS THE TAHOE. I HAVE DONE SOME RESEARCH AND IT SEEMS TO BE A VERY COMMON OCCURRENCE IN 07-14 TAHOES/SILVERADO/SIERRA/YUKON/SUBURBANS. I ALSO WORK AT A LARGE GOVERNMENT AGENCY AND HAVE FOUND THIS HAS OCCURRED IN VEHICLES THAT WERE PURCHASED NEW BY MY AGENCY. THIS MANUFACTURE DEFECT IS VERY CONCERNING. IF THE AIRBAGS WERE TO DEPLOY, THE DASH WOULD SHATTER AND CAUSE SERIOUS INJURIES. I CONTACTED GM AND WAS TOLD THERE IS NOTHING THAT CAN BE DONE. I WAS TOLD THERE ARE NO RECALLS AND TO MAKE A COMPLAINT TO YOU. IT WAS EXPLAINED TO ME THAT IF I BOUGHT THE CAR NEW, THEN MAYBE THERE WOULD BE SOMETHING THAT COULD BE DONE. GM STATED THEY DO NOT KNOW WHAT THE PREVIOUS OWNER COULD HAVE DONE TO THE DASH. GM COULD NOT ELABORATE THIS CLAIM. I ASKED IF I PURCHASE A NEW DASH, INSTALLED BY GM AND THE DEFECT OCCURS AGAIN; WOULD THEY THEN REPLACE IT. GM STATED NO IF IT OUT OF WARRANTY. I AM WRITING TO YOU TO SHOW MY CONCERN FOR THIS DEFECT AND THE LACK OF CONCERN BY THE COMPANY DISTRIBUTING THESE PRODUCTS. I FIND IT UNETHICALL TO DISTRIBUTE A PRODUCT WHEN THEY KNOW THERE IS A KNOWN ISSUE. I HAVE ATTACHED PHOTOS OF MY VEHICLE AS IT IS NOW. I ALSO LOCATED A OLD PICTURE FROM OUR OLD VEHICLE. THIS VEHICLE IS GARAGE PARKED AND DRIVEN BY MY WIFE SO THERE IS NO ABUSE DONE. CAN SOMEONE REVIEW THIS AND CONTACT ME TO SEE WHAT CAN BE DONE?
MY DASHBOARD FROM THE PASSENGER SIDE TO THE DRIVERS SIDE INCLUDING THE AREA OVER THE GAUGES IS CRACKED AND SOME SECTIONS FELL IN UNDER THE DASH, LEAVING A HOLE. MY CONCERN IS IF THE AIRBAG DEPLOYS, THE DASHBOARD WILL TURN INTO SHRAPNEL AND SERIOUSLY INJURE OR KILL THE OCCUPANTS. *TR
2013 YUKON XL WAS FOUND TO HAVE EXCESSIVE RUST ON THE FRAME AND OTHER PARTS UNDERNEATH THE VEHICLE DURING AN ANNUAL INSPECTION. THE WAX COATING IF FLAKING OFF THE FRAME LEAVING BARE METAL THAT QUICKLY RUSTS. GM CLAIMS THAT THE DAMAGE IS ENVIRONMENTAL AND THE ISSUES IS THE SALT USED ON PA ROADS. IF THIS IS THE CASE, THEN GM SHOUL…
Read full complaint
2013 YUKON XL WAS FOUND TO HAVE EXCESSIVE RUST ON THE FRAME AND OTHER PARTS UNDERNEATH THE VEHICLE DURING AN ANNUAL INSPECTION. THE WAX COATING IF FLAKING OFF THE FRAME LEAVING BARE METAL THAT QUICKLY RUSTS. GM CLAIMS THAT THE DAMAGE IS ENVIRONMENTAL AND THE ISSUES IS THE SALT USED ON PA ROADS. IF THIS IS THE CASE, THEN GM SHOULD WARN ALL CUSTOMERS THAT THEIR VEHICLES ARE NOT BUILT TO LAST IN THE STATE OF PA AND THAT THEY WILL NOT HONOR THEIR WARRANTY. NONE OF OUR OTHER VEHICLES ARE RUSTING. THEIR ARE MANY OTHER PEOPLE COMPLAINING ABOUT THE SAME ISSUES AND THE PROBLEM HAS BEEN NOTED TO START DURING THE FIRST YEAR OF OWNERSHIP BEFORE GOING THROUGH THE WINTER. THEY HAVE NOT PROPERLY COATED THE FRAME TO WITHSTAND RUST. I HAD TO PAY FOR UNDERCOATING NOW TO RECTIFY THE PROBLEM. THE UNDERCOATING INSTALLER MENTIONED THIS IS A KNOW PROBLEM WITH GM TRUCKS AND THE COMPANY REFUSES TO ACKNOWLEDGE OR ADDRESS THE ISSUE. *TR
MY DASH BOARD IS CRACKED AROUND THE AIRBAG LOCATION ON THE PASSENGER SIDE OF THE VEHICLE. RESEARCHING THIS HAS SHOWN THAT IT'S A REOCCURRING DEFECT IN THE YUKON, SIERRA, SILVERADO, TAHOE AND SURBURBAN MODELS. THERE ARE NUMEROUS REPORTS OF THE SAME ISSUE WITHOUT ANY CORRECTIVE ACTION BY THE MANUFACTURER SHORT OF A REPLACEMENT "…
Read full complaint
MY DASH BOARD IS CRACKED AROUND THE AIRBAG LOCATION ON THE PASSENGER SIDE OF THE VEHICLE. RESEARCHING THIS HAS SHOWN THAT IT'S A REOCCURRING DEFECT IN THE YUKON, SIERRA, SILVERADO, TAHOE AND SURBURBAN MODELS. THERE ARE NUMEROUS REPORTS OF THE SAME ISSUE WITHOUT ANY CORRECTIVE ACTION BY THE MANUFACTURER SHORT OF A REPLACEMENT "CASE BY CASE" BASIS.
THE DASHBOARD IS CRACK. LOOKS LIKE A VEHICLE WAS SOLD TO ME AND THEY FIXED THE CRACK BUT AFTER I BEEN DRIVING FOR 2 MONTHS THE CRACK IS THERE.
DASHBOARD CRACKING NEAR AIRBAG, NOTICED IT THIS MORNING AFTER DROPPING KIDS AT SCHOOL. CAR IS GARAGE KEPT.
Official recalls
421V053000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.
21V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
14V614000 · Electrical System
Oct 1, 2014
General Motors LLC (GM) is recalling certain model year 2013-2014 Cadillac CTS, Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, GMC Yukon, and Yukon XL, and 2014 Buick Enclave, Chevrolet Express, Impala, Silverado HD, Traverse, GMC Acadia, Savana, and Sierra HD vehicles. In the affected vehicles, the chassis electronic module may be internally contaminated, resulting in an electrical short.
Consequence & remedy
Consequence: If the module experiences an electrical short, the vehicle could stall, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the chassis electronic module, free of charge. The recall began on December 26, 2014. Owners may contact GM customer service at 1-800-521-7300 (Buick), 1-800-458-006 (Cadillac), 1-800-222-1020 (Chevrolet), and 1-800-462-8782 (GMC). GMs number for this recall is 14515.
13V001000 · Power Train:automatic Transmission; Steering:column LOCKING:ANTI-THEFT Device
Jan 2, 2013
General Motors (GM) is recalling certain model year 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Express, Silverado HD, Silverado LD, Suburban, and Tahoe; and GMC Savana, Sierra HD, Sierra LD, Yukon, and Yukon XL vehicles, manufactured between November 7, 2012, through December 18, 2012, for failing to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 102, "Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect", and FMVSS No. 114, "Theft Protection and Rollaway Prevention." The vehicles may have been built with a fractured park lock cable or a malformed steering column lock actuator gear in the lock module assembly.
Consequence & remedy
Consequence: As a result, the vehicle may shift from Park with the ignition key removed or the ignition key in the OFF position. The vehicle may also shift out of Park without application of the brake pedal while the key is off. Either of these scenarios may cause the vehicle to roll away after the driver has exited the vehicle, resulting in a possible vehicle crash and/or injury.
Remedy: GM will notify owners, and dealers will inspect the affected vehicles and replace the steering column as necessary, free of charge. The recall began on January 21, 2013. Chevrolet owners may call 1-800-630-2438. Cadillac owners may call 1-866-982-2339. GMC owners may call 1-866-996-9463.
Additional source detail variants (2)
Power Train:automatic Transmission
General Motors (GM) is recalling certain model year 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Express, Silverado HD, Silverado LD, Suburban, and Tahoe; and GMC Savana, Sierra HD, Sierra LD, Yukon, and Yukon XL vehicles, manufactured between November 7, 2012, through December 18, 2012, for failing to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 102, "Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect", and FMVSS No. 114, "Theft Protection and Rollaway Prevention." The vehicles may have been built with a fractured park lock cable or a malformed steering column lock actuator gear in the lock module assembly.
Consequence: As a result, the vehicle may shift from Park with the ignition key removed or the ignition key in the OFF position. The vehicle may also shift out of Park without application of the brake pedal while the key is off. Either of these scenarios may cause the vehicle to roll away after the driver has exited the vehicle, resulting in a possible vehicle crash and/or injury.
Remedy: GM will notify owners, and dealers will inspect the affected vehicles and replace the steering column as necessary, free of charge. The recall began on January 21, 2013. Chevrolet owners may call 1-800-630-2438. Cadillac owners may call 1-866-982-2339. GMC owners may call 1-866-996-9463.
Steering:column LOCKING:ANTI-THEFT Device
General Motors (GM) is recalling certain model year 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Express, Silverado HD, Silverado LD, Suburban, and Tahoe; and GMC Savana, Sierra HD, Sierra LD, Yukon, and Yukon XL vehicles, manufactured between November 7, 2012, through December 18, 2012, for failing to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 102, "Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect", and FMVSS No. 114, "Theft Protection and Rollaway Prevention." The vehicles may have been built with a fractured park lock cable or a malformed steering column lock actuator gear in the lock module assembly.
Consequence: As a result, the vehicle may shift from Park with the ignition key removed or the ignition key in the OFF position. The vehicle may also shift out of Park without application of the brake pedal while the key is off. Either of these scenarios may cause the vehicle to roll away after the driver has exited the vehicle, resulting in a possible vehicle crash and/or injury.
Remedy: GM will notify owners, and dealers will inspect the affected vehicles and replace the steering column as necessary, free of charge. The recall began on January 21, 2013. Chevrolet owners may call 1-800-630-2438. Cadillac owners may call 1-866-982-2339. GMC owners may call 1-866-996-9463.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.