NHTSA owner reports · September 18, 2026 snapshot.
Steering complaints
154 reportsClear category filter62,000 miles · Jan 29, 2018
Electrical SystemExterior LightingSteering
DURING DRIVING, THE STABILITY SENSORS WOULD GO OFF AND SHOW UP STATING STABILITY TURNED OFF, OR POWER STEERING TURNED OFF. THE VOLTAGE ON VEHICLE WOULD SUDDENLY DROP FROM 15 TO 9 AND THEN BACK UP. THIS WILL USUALLY TURN OFF THE INTERIOR LIGHTS AND ELECTRONICS. I HAVE DISCUSSED THIS WITH OTHER 2014 SIERRA AND SILVERADO OWNERS AND…
Read full complaint
DURING DRIVING, THE STABILITY SENSORS WOULD GO OFF AND SHOW UP STATING STABILITY TURNED OFF, OR POWER STEERING TURNED OFF. THE VOLTAGE ON VEHICLE WOULD SUDDENLY DROP FROM 15 TO 9 AND THEN BACK UP. THIS WILL USUALLY TURN OFF THE INTERIOR LIGHTS AND ELECTRONICS. I HAVE DISCUSSED THIS WITH OTHER 2014 SIERRA AND SILVERADO OWNERS AND THEY ALL ADVISED THIS WAS OCCURING ON THEIR VEHICLES. THERE IS A GROUND WIRE THAT WAS NOT PROPERLY INSTALLED UNDER THE DASH WHICH CAUSES HIGH RESISTANCE MATERIAL TO CAUSE ELECTRICAL ISSUES. DURING ONE OF MY DRIVES TO WORK GOING 60 MPH, THE ELECTRICAL COMPONENTS SHUT OFF AND CAUSED THE ENGINE TO STOP RUNNING. I WAS ABLE TO PULL OVER WHILE COASTING ON NO POWER AND RESTART THE VEHICLE AND IT WOULD CONTINUE TO GO. THERE HAVE BEEN TIMES WHERE THE STEERING WHEEL WOULD JERK WHILE STATIONARY AS WELL. AFTER MANY FORUM DISCUSSION THIS ALL RELATED BACK TO THE GROUND WIRE NOT BEING PROPERLY INSTALLED BY THE MANUFACTURER.
NHTSA ODI #11065703
24,045 miles · Jan 17, 2018
SteeringSuspensionWheels
DEC. 11,2017 DRIVING UNDER 20 MPH ON A LOCAL ROAD SPEED LIMIT 30MPH BALL JOINT PULLED OUT OF CONTROL ARM FRONT DRIVERS SIDE. FRONT WHEEL FELL OVER CAUSED DAMAGE TO TIRE AND RIM AND DISABLED ABS SYSTEM BY CUTTING WIRES. LUCKY I WAS NOT ON INTERSTATE 84 GOING 65 MPH IN FISHKILL NEW YORK TRUCK COULD HAVE CRASHED WITH OTHER VEHICLE…
Read full complaint
DEC. 11,2017 DRIVING UNDER 20 MPH ON A LOCAL ROAD SPEED LIMIT 30MPH BALL JOINT PULLED OUT OF CONTROL ARM FRONT DRIVERS SIDE. FRONT WHEEL FELL OVER CAUSED DAMAGE TO TIRE AND RIM AND DISABLED ABS SYSTEM BY CUTTING WIRES. LUCKY I WAS NOT ON INTERSTATE 84 GOING 65 MPH IN FISHKILL NEW YORK TRUCK COULD HAVE CRASHED WITH OTHER VEHICLES OR CAUSED SERIOUS INJURY TO OCCUPANTS OF MY VEHICLE COULD HAVE CAUSED VEHICLE TO ROLL OVER. DEALER CLAIMED NEVER HEARD OF THIS HAPPENING AND THAT I MUST HAVE HIT SOMETHING TO CAUSE THE BALL JOINT TO PULL OUT OF CONTROL ARM, NEVER HIT ANYTHING NOT EVEN A POT HOLE I AM THE ONLY DRIVER OF THIS VEHICLE. HAD TO REPLACE CONTROL ARM WHICH HOLDS THE UPPER BALL JOINT WHICH IS PRESSED INTO CONTROL ARM. TOOK DEALER FROM MONDAY TO FRIDAY TO COMPLETE REPAIRS. CONTROL ARM NOT UNDER WARRANTY REPAIRS COST 936.42. FOUND MANY COMPLAINTS ABOUT BALL JOINT AND CONTROL ARM SEPARATING ON THIS VEHICLE ONLINE. DRIVER SIDE FRONT BALL JOINT. *JS
NHTSA ODI #11063240
63,000 miles · Dec 5, 2017
Electronic Stability Control (esc)Steering
ON OR ABOUT 4 APRIL, 2017 I EXPERIENCED AN ALARM WHILE DRIVING MY 2014 GMC SIERRA. WHILE TRAVELING BETWEEN CONROE TX AND PLANO TX, I RECEIVED A WARNING STEERING STABILITY. THE ALARM CLEARED SO I CHECKED MY OWNERS MANUAL AND IT SAID TO TAKE IT TO A DEALER IF IT DIDN'T CLEAR. I USED ONSTAR AND HAD A DIAGNOSIS DONE ON THE TRUCK…
Read full complaint
ON OR ABOUT 4 APRIL, 2017 I EXPERIENCED AN ALARM WHILE DRIVING MY 2014 GMC SIERRA. WHILE TRAVELING BETWEEN CONROE TX AND PLANO TX, I RECEIVED A WARNING STEERING STABILITY. THE ALARM CLEARED SO I CHECKED MY OWNERS MANUAL AND IT SAID TO TAKE IT TO A DEALER IF IT DIDN'T CLEAR. I USED ONSTAR AND HAD A DIAGNOSIS DONE ON THE TRUCK. THEY REPORTED NO PROBLEMS. THE NEXT DAY THE TRUCK SHUT DOWN, IN THE MIDDLE OF MAKING A U TURN. MY DAUGHTER THOUGHT SHE HAD KNOCKED IT OUT OF GEAR BUT COULDN'T GET IT TO START UNTIL SHE TURNED IT OFF AND BACK ON. THE SAME THING HAPPENED AGAIN (THIS TIME TO MY WIFE) TURNING INTO A PARKING LOT. SHE TOOK IT TO A GMC DEALER TO HAVE IT CHECKED OUT. THEY FOUND A BROKEN GEAR IN THE ELECTRONIC POWER ASSIST ASSEMBLY. WE HEARD THAT OUR VEHICLE HAD A RECALL # 17276, FOR PROBLEM WITH THE STEERING. I THEN TOOK IT TO THE DEALER WHERE I BOUGHT THE TRUCK AND HAD THE COMPUTER UPDATED TO PREVENT THE PROBLEM. I THEN ASK FOR A REIMBURSEMENT FOR HAVING TO HAVE THE STEERING MODULE AND NEGATIVE BATTERY CABLE REPLACED. I CONTEND THAT, AT THE TIME, THE CAUSE OF THE STEERING PROBLEM CAUSING THE TRUCK TO DIE. WHEN I ASK A TECHNICIAN AT MCKINNEY IF THE RECALL WAS FOR THE PROBLEM, HE SAID: NO THAT IS JUST TO CHANGE AN ERROR IN THE COMPUTER. BACK IN APRIL, THE ONLY THING THEY COULD DO TO POSSIBLY PREVENT THE STALLING WAS TO LOOK FOR SOMETHING LIKE A POWER PROBLEM. BEFORE I TOOK THE TRUCK IN I HAD NO INDICATION OF POWER PROBLEMS AND I WAS NEVER TOLD HOW THE NEGATIVE BATTERY CABLE WENT BAD, ONLY THAT IT HAPPENS AND THE TRUCK WAS OUT OF THE 36 MO WARRANTY. I CHECKED ON THE INTERNET TO SEE IF ANYONE ELSE WAS HAVING THE PROBLEM AND WHAT THE SOLUTION TO IT WAS? I SAW SEVERAL PEOPLE WERE HAVING THE PROBLEM, BUT NOBODY KNEW WHAT EXACTLY CAUSED IT. THE CONSUMER REQUESTED TO BE FULLY REIMBURSED FOR THE REPAIRS MADE REFERENCING THE RECALL #17276. *JS
NHTSA ODI #11052633
45,000 miles · Dec 3, 2017
Electrical SystemSteering
2014 GMC SIERRA CURRENTLY WITH 45,000 MILES. VEHICLE SPENT 40+ DAYS AT DEALERSHIP IN 2016 FOR VIBRATION WHILE DRIVING BETWEEN 69-72 MPH THEY COULD NOT FIX DURING 6 DIFFERENT SERVICE VISITS. IT WAS UNDER 3 YEAR/36K MILE WARRANTY AT THE TIME. BEGAN AT 22,000 MILES. IN NOV. 2017 VEHICLE BEGAN LOSING POWER STEERING AT SPEEDS UN…
Read full complaint
2014 GMC SIERRA CURRENTLY WITH 45,000 MILES. VEHICLE SPENT 40+ DAYS AT DEALERSHIP IN 2016 FOR VIBRATION WHILE DRIVING BETWEEN 69-72 MPH THEY COULD NOT FIX DURING 6 DIFFERENT SERVICE VISITS. IT WAS UNDER 3 YEAR/36K MILE WARRANTY AT THE TIME. BEGAN AT 22,000 MILES. IN NOV. 2017 VEHICLE BEGAN LOSING POWER STEERING AT SPEEDS UNDER 3 MPH, ESPECIALLY IN REVERSE. ALSO SERVICE STABILITRAK LIGHT HAS COME ON RANDOMLY AT LOW SPEEDS. PROBLEM WAS INTERMITTENT BUT IS NOW BECOMING AN ALMOST DAILY OCCURRANCE. AFRAID THIS WILL LEAD TO AN ACCIDENT. SEVERAL CLOSE CALLS ALREADY. RADIO HAS ALSO TURNED OFF ON ITS ON ABOUT 5 TIMES IN THE LAST 60 DAYS. IT WILL NOT TURN BACK ON UNTIL VEHICLE IS RE-STARTED. RELATED OR UNRELATED, WHILE DRIVING AT NIGHT AND APPLYING BRAKE PEDAL I NOTICE A 1/2 SECOND DIMMING OF HEADLIGHTS AND DASH LIGHTS BEFORE THEY RETURN TO NORMAL BRIGHTNESS. BATTERY AND ALTERNATOR TESTED FINE BY DEALERSHIP. DEALERSHIP SAYS VEHICLE VIN IS NOT SUBJECT TO ANY RECALLS. DEALERSHIP WANTS ME TO REPLACE POWER STEERING GEAR FOR $2,500 WHICH THEY "THINK" MIGHT FIX THE PROBLEM. DON'T WANT TO SPEND $2,500 WITHOUT CERTAINTY IT IS THE PROBLEM.
NHTSA ODI #11052114
75,500 miles · Nov 28, 2017
Electrical SystemElectronic Stability Control (esc)Steering
THE FIRST TIME I WAS DRIVING DOWN THE HIGHWAY AND I HIT THE BRAKES AND THE DIC SAID SERVICE STABILITRAK AND A FEW OTHER THINGS AND I LOST CONTROL OF STEERING AND MY CRUISE WOULDN'T WORK FOR A MINUTE THE SECOND TIME I WAS DRIVING DOWN THE ROAD AND I GASES ON IT AND THE WHOLE TRUCK SHUTOFF AND BACK ON BUT I LOST CONTROL OF THE STE…
Read full complaint
THE FIRST TIME I WAS DRIVING DOWN THE HIGHWAY AND I HIT THE BRAKES AND THE DIC SAID SERVICE STABILITRAK AND A FEW OTHER THINGS AND I LOST CONTROL OF STEERING AND MY CRUISE WOULDN'T WORK FOR A MINUTE THE SECOND TIME I WAS DRIVING DOWN THE ROAD AND I GASES ON IT AND THE WHOLE TRUCK SHUTOFF AND BACK ON BUT I LOST CONTROL OF THE STEERING AGAIN THEN I TURNED IN MY DRIVEWAY AND LOST ALL STEERING AND ALL POWER AND THE TRUCK DIED I HAD TO TURN THE KEY 2 OR 3 TIMES AND IF FINALLY STARTED IT LOST ALL POWER IT RESET MY CLOCK AND EVERYTHING ON MY RADIO AND DIC
NHTSA ODI #11050964
34,941 miles · Nov 22, 2017
Steering
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE DRIVING 5 MPH, THE STEERING WHEEL SEIZED BEFORE THE VEHICLE ACCELERATED. THE CONTACT DROVE THE VEHICLE TO WILSON COUNTY CHEVROLET BUICK GMC (903 S HARTMANN DR, LEBANON, TN 37090 (615) 444-9642). THE CONTACT WAS INFORMED THAT THE VEHICLE WAS INCLUDED IN AN UNKNOWN RECALL AND IT W…
Read full complaint
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE DRIVING 5 MPH, THE STEERING WHEEL SEIZED BEFORE THE VEHICLE ACCELERATED. THE CONTACT DROVE THE VEHICLE TO WILSON COUNTY CHEVROLET BUICK GMC (903 S HARTMANN DR, LEBANON, TN 37090 (615) 444-9642). THE CONTACT WAS INFORMED THAT THE VEHICLE WAS INCLUDED IN AN UNKNOWN RECALL AND IT WAS REPAIRED FOR FREE. AFTER THE REMEDY, THE VEHICLE WAS OPERABLE, BUT THE FAILURE RECURRED IN LESS THAN 24 HOURS. THE STEERING WHEEL SEIZED A SECOND TIME AND EXCESSIVE FORCE ON THE STEERING WHEEL WAS USED, BUT THE WHEEL WOULD NOT TURN. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE MANUFACTURER WAS NOT CONTACTED. THE VEHICLE WAS NOT SERVICED FOR THE SECOND FAILURE. THE FAILURE MILEAGE WAS 34,941.
NHTSA ODI #11048004
30,000 miles · Nov 15, 2017
Steering
WHEN MAKING A FULL TURN TO THE LEFT WITH MY 2014 GMC SIERRA THERE IS A LOUD THUMPING NOISE THAT YOU CAN ALSO FEEL IN THE STEERING WHEEL. THE PROBLEM STARTED PERIODICALLY AND I HAD A DEALERSHIP DIAGNOSIS. THEY HEARD THE NOISE AND FOUND NO PROBLEMS. THE NOISE HAS BECOME MORE CONSISTENT AND A THIRD PARTY MECHANIC BELIEVES IT TO BE …
Read full complaint
WHEN MAKING A FULL TURN TO THE LEFT WITH MY 2014 GMC SIERRA THERE IS A LOUD THUMPING NOISE THAT YOU CAN ALSO FEEL IN THE STEERING WHEEL. THE PROBLEM STARTED PERIODICALLY AND I HAD A DEALERSHIP DIAGNOSIS. THEY HEARD THE NOISE AND FOUND NO PROBLEMS. THE NOISE HAS BECOME MORE CONSISTENT AND A THIRD PARTY MECHANIC BELIEVES IT TO BE A STEERING RACK FAILURE. THE VEHICLE CAN BE STATIONARY OR MOVING AT PARKING LOT SPEEDS TO HEAR THE THUMP.
NHTSA ODI #11046187
44,000 miles · Nov 9, 2017
Electronic Stability Control (esc)SteeringVehicle Speed Control
YESTERDAY I WAS DRIVING HOME ON THE HIGHWAY DRIVING APPROXIMATELY 75MPH WHEN WITHOUT ANY WARNING A STABILITY STEERING CONTROL LIGHT FLASHED ON THE DASHBOARD BEHIND MY STEERING WHEEL. THE CAR IMMEDIATELY JOLTED FROM DRIVING MID 70'S DOWN TO AN IMMEDIATE 67MPH. THIS SPEED LIMIT WAS THE LAST THING THAT FLASHED BEFORE MY DASHBOARD B…
Read full complaint
YESTERDAY I WAS DRIVING HOME ON THE HIGHWAY DRIVING APPROXIMATELY 75MPH WHEN WITHOUT ANY WARNING A STABILITY STEERING CONTROL LIGHT FLASHED ON THE DASHBOARD BEHIND MY STEERING WHEEL. THE CAR IMMEDIATELY JOLTED FROM DRIVING MID 70'S DOWN TO AN IMMEDIATE 67MPH. THIS SPEED LIMIT WAS THE LAST THING THAT FLASHED BEFORE MY DASHBOARD BLACKED OUT, THE STEERING COLUMN LOCKED AND THE VEHICLE ENTIRELY LOST POWER WHILE DRIVING. SECONDS LATER MY WINDSHIELD WIPERS SPORADICALLY STARTED MOVING (I DID NOT ENGAGE THE SWITCH) AND I WATCHED THE TEMPERATURE GO UP FROM 70 TO 80 WITHOUT TOUCHING THE GAUGE MANUALLY. THE CAR JOLTED FOR ALMOST 10 MILES SPORADICALLY LOSING CONTROL INTERMITTENTLY AND WHEN I EXITED OFF THE HIGHWAY AND MADE A LEFT HAND TURN AT A LOW SPEED (UNDER 15MPH) THE STEERING COMPLETELY LOCKED AND THE CAR PULLED OFF TO THE SIDE OF THE ROAD TOWARD A CURB. I GAINED CONTROL OF THE VEHICLE MANUALLY WHICH WAS DIFFICULT BUT I DID CORRECT THE DRIVE PATH BACK ONTO THE ROAD. I PULLED INTO THE DEALERSHIP AT A LOW RATE OF SPEED AND THE CAR DID THE SAME THING AS IT DID WHEN I EXITED THE HIGHWAY. I'M IN A LOANER AND THE DEALER HAS MY VEHICLE. THIS VEHICLE WAS PURCHASED USED ROUGHLY 2 MONTHS AGO FROM A REGISTERED GMC DEALER WITH 40K MILES ON IT. IT NOW HAS ROUGHLY 44K ON IT. I HAVE MADE 1 PAYMENT ON THIS VEHICLE THUS FAR.
NHTSA ODI #11044805
47,000 miles · Oct 22, 2017
SteeringVehicle Speed Control
COMPLETE LOSS OF POWER STEERING ALONG WITH SPEED CONTROL BEING DISABLED WHEN A TURN SIGNAL IS ACTIVATED. RECALL 17V414000 HAS ALREADY BEEN COMPLETED AND DID NOT CORRECT THE PROBLEM. BOTH OF THESE ISSUES OCCUR DURING THE SAME DRIVE CYCLE (ISSUES HAVE NOT HAPPENED SIMULTANEOUSLY BUT WILL BOTH OCCUR AT SOME POINT DURING THE SAME …
Read full complaint
COMPLETE LOSS OF POWER STEERING ALONG WITH SPEED CONTROL BEING DISABLED WHEN A TURN SIGNAL IS ACTIVATED. RECALL 17V414000 HAS ALREADY BEEN COMPLETED AND DID NOT CORRECT THE PROBLEM. BOTH OF THESE ISSUES OCCUR DURING THE SAME DRIVE CYCLE (ISSUES HAVE NOT HAPPENED SIMULTANEOUSLY BUT WILL BOTH OCCUR AT SOME POINT DURING THE SAME DRIVE CYCLE) THEY SEEM TO ONLY HAPPEN ON DRIVE CYCLES THAT LAST LONGER THAN 45 MINUTES.
NHTSA ODI #11042328
Mileage unknown · Oct 13, 2017
Steering
POWER STEERING RECALL. I HAVE BEEN IN TOUCH WITH MY NEARBY GMC DEALER FOR THE PAST 2 MONTHS ATTEMPTING TO GET THIS RECALL DEALT WITH AND FIXED. I NEED THIS RECALL TO BE RESOLVED NO LATER THAN 20 OCT 17 IN ORDER FOR MY VEHICLE TO BE SHIPPED TO MY NEW DUTY STATION IN ALASKA AS I WILL BE DOING A PCS (PERMANENT CHANGE OF STATION) FO…
Read full complaint
POWER STEERING RECALL. I HAVE BEEN IN TOUCH WITH MY NEARBY GMC DEALER FOR THE PAST 2 MONTHS ATTEMPTING TO GET THIS RECALL DEALT WITH AND FIXED. I NEED THIS RECALL TO BE RESOLVED NO LATER THAN 20 OCT 17 IN ORDER FOR MY VEHICLE TO BE SHIPPED TO MY NEW DUTY STATION IN ALASKA AS I WILL BE DOING A PCS (PERMANENT CHANGE OF STATION) FOR THE ARMY. IF IT CAN'T BE RESOLVED BY THEN I NEED SOME TYPE OF DOCUMENTATION SENT TO ME STATING IT CAN'T BE RESOLVED DUE TO GMC LACKING ABILITY TO FIX THE PROBLEM OR REMOVE THE RECALL FROM MY VEHICLE. PLEASE EMAIL THE DOCUMENTATION TO [XXX]. VERY RESPECTFULLY, [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).'*JB
NHTSA ODI #11033228
Official recalls
9Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Apr 12, 2016
General Motors LLC (GM) is recalling certain model year 2014-2015 Chevrolet Silverado 1500 and GMC Sierra 1500 trucks manufactured January 29, 2013, to January 21, 2015. While entering the vehicle, the seat belt tensioner cable may be positioned such that the driver slides over it. This movement may result in the fatigue and separation of the cable.
Consequence & remedy
Consequence: If the tensioner cable separates, the driver may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will modify the vehicles to prevent the tensioner from being damaged. Any tensioner that has already been damaged will be replaced, free of charge. The recall began on August 11, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 15822.
Jan 13, 2014
General Motors is recalling certain 2014 model year Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles, and 2015 model year Cadillac Escalade and Escalade ESV; Chevrolet Silverado HD; and GMC Sierra HD, Yukon, and Yukon XL, equipped with a 4.3L engine or 5.3L engine.
Consequence & remedy
Consequence: The overheated exhaust components may melt nearby plastic parts and may result in an engine fire.
Remedy: General Motors will notify owners, and dealers will reprogram the engine control module, free of charge. The recall began on January 16, 2014. Owners may contact Chevrolet at 1-800-222-1020 and GMC at 1-800-462-8782. General Motors' number for this recall is 14008.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration