← New search

2011 GMC Sierra 1500

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2011 GMC Sierra 1500 do not stand out strongly from the model-year median of 181.

About this comparison →

When problems were reported

Mileage at the reported incident

151 reports with mileage · 133 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 113 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Power Train. Review the 24 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

5 crash reports3 fire reports5 injury reports

What owners actually said

284 reports
Mileage unknown · Aug 11, 2026
Electrical SystemService Brakes

ABS Randomly turns on with the traction control light… All windows except for driver window will not go down and sometimes it does not unlock or lock sometimes. It started the beginning of 2022 and has got worst over the years. It is available for inspection. Safety has been and issue because whenever it rains it can lose contro…

Read full complaint

ABS Randomly turns on with the traction control light… All windows except for driver window will not go down and sometimes it does not unlock or lock sometimes. It started the beginning of 2022 and has got worst over the years. It is available for inspection. Safety has been and issue because whenever it rains it can lose control on the road haven’t had the money to fix it so don’t really drive it right now.

NHTSA ODI #11756351

Mileage unknown · Mar 13, 2026
Power TrainService BrakesSteering

Vehicle experienced a catastrophic mechanical failure characterized by a percussive "shotgun blast" noise from the rear chassis, followed by an immediate, total loss of braking power (pedal to the floor) and a violent loss of directional stability. This incident represents an aggravated safety failure of known GMT900 platform de…

Read full complaint

Vehicle experienced a catastrophic mechanical failure characterized by a percussive "shotgun blast" noise from the rear chassis, followed by an immediate, total loss of braking power (pedal to the floor) and a violent loss of directional stability. This incident represents an aggravated safety failure of known GMT900 platform defects. The technical chain of causality began with the factory exhaust manifold fasteners suffering a metallurgical shear, a universal defect documented under GM Bulletins 19-NA-218, PIP5075, and PIP4701. This shear created a high-velocity, high-heat exhaust leak directed at the brake master cylinder and vacuum assembly. This "heat soak" event compromised the engine-mounted mechanical Brake Vacuum Pump (Recall N192268490 / NHTSA 19V645) and destroyed the internal seals of the Master Cylinder (Special Coverage 15143 / NHTSA 11V599), resulting in total depletion of vacuum assist and hydraulic pressure. Simultaneously, the "shotgun blast" and violent swerve were caused by structural failure consistent with Rear Brake Caliper Bolt Fracture (GM 13247 / NHTSA 13V342) and Rear Axle Shaft/Pin Fracture (GM 14892 / NHTSA 14V819). This mechanical collapse caused the caliper to strike the wheel, resulting in a catastrophic rim blowout and immediate loss of tire pressure. Despite the vehicle having aftermarket long-tube headers installed, the root cause of the heat-related brake failure was the failure of the OEM GM manifold fasteners which snapped off in the cylinder head, as documented in the aforementioned bulletins. Under the Magnuson-Moss Warranty Act, the manufacturer remains liable for these pre-existing safety-critical defects. The vehicle is at Glenn Polk Chevrolet for a 901-series Product Allegation Investigation (Case #90199492). This report is filed to demand federal oversight into these life-threatening defects. The combo of failed fasteners, rim blowout, and compromised braking created a vehicle that was both unable to be steered or stopped

NHTSA ODI #11724011

Mileage unknown · Sep 11, 2025
Structure

The door handle broke off on the driver side the passenger side door handle will not open the door the outside handles are loose and the rear back driver and passenger side will not open their doors.

NHTSA ODI #11686729

Mileage unknown · Jul 26, 2025
Unknown Or Other

Frame falling apart the coating peeled off was going to clean it to recoat it but the metal is so far gone took it to a frame shop only to find out it's not drivable anymore GM have to do better with the coating for this trucks

NHTSA ODI #11676427

Mileage unknown · Jul 8, 2025
StructureUnknown Or Other

2011 GMC Sierra Frame Failed Pennsylvania State Inspection due to Driver Side Frame Rust/hole. The section of the frame must be replaced due to rust(Improper coating... The truck has only 69700 miles on the odometer.

NHTSA ODI #11672122

128,000 miles · Apr 18, 2025
Electrical System

Odometer Fraud. The contact purchased a 2011 GMC Sierra 1500. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the mileage was 119,000, and at the time of registration, it was discovered that the mile…

Read full complaint

Odometer Fraud. The contact purchased a 2011 GMC Sierra 1500. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the mileage was 119,000, and at the time of registration, it was discovered that the mileage was 128,000.

NHTSA ODI #11655497

Mileage unknown · Jan 27, 2025
Structure

Vehicle is up for inspection in February of 2025 and due to the frame rust it will not pass.

NHTSA ODI #11638839

Mileage unknown · Dec 12, 2024
Electrical SystemForward Collision Avoidance

When I put the truck in 4wd the dash says service stabilitrak and the traction control light and abs light come on

NHTSA ODI #11630263

Mileage unknown · Sep 16, 2024
Structure

My GMC which is well cared for and only has 121,000 miles has a rusted through frame (mid-vehicle, left side) which has made the truck unsafe to drive. The steel used is inferior, my neighbor across the street also has this truck, 2 years newer, and is doing the same thing. As I have researched this issue I have found out that t…

Read full complaint

My GMC which is well cared for and only has 121,000 miles has a rusted through frame (mid-vehicle, left side) which has made the truck unsafe to drive. The steel used is inferior, my neighbor across the street also has this truck, 2 years newer, and is doing the same thing. As I have researched this issue I have found out that this is a critical failure of the GMC Sierra for several model years due to a failure to protect the steel used in northern states which compromises structural integrity. When Toyota had this issue, they stepped up and replaced the frames. General Motors, please tell me what you intend to do with this. It is a 5.3 Litre with 121,000 miles on it, in other words, still a baby for such a fine engine. This is not right. I am seriously discouraged. For my family, this is devastating. I still owe $2000 on this vehicle. Thank you, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ODI #11614743

Mileage unknown · Aug 13, 2024
Air Bags

See attached document for complaint

NHTSA ODI #11608147

Official recalls

5

21V050000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.

21V054000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.

18V267000 · Equipment

Apr 26, 2018

General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf

Consequence & remedy

Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.

11V007000 · Suspension:rear:axle:spindle

Jan 6, 2011

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2011 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, COLORADO, EXPRESS, SILVERADO, SUBURBAN, TAHOE; AND GMC CANYON, SIERRA, SAVANA, YUKON AND YUKON XL VEHICLES. THE REAR AXLE CROSS PINS WERE NOT PROPERLY HEAT TREATED AND COULD FRACTURE AND BECOME DISPLACED WITHIN THE REAR AXLE. SHOULD THE PIN SHIFT OUT OF POSITION, IT COULD CREATE AN INTERFERENCE CONDITION AND CAUSE THE REAR AXLE TO LOCK.

Consequence & remedy

Consequence: THE DRIVER MAY NOT BE ABLE TO MAINTAIN DIRECTIONAL CONTROL OF THE VEHICLE AND A CRASH COULD OCCUR WITHOUT WARNING.

Remedy: DEALERS WILL INSTALL A NEW REAR AXLE CROSS PIN FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463 AND AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.

10V643000 · Suspension:rear:axle:spindle

Dec 17, 2010

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2011 CADILLAC ESCALADE EXT, CHEVROLET AVALANCHE, SILVERADO LD AND GMC SIERRA LD VEHICLES. THE REAR AXLE CROSS PINS WERE NOT PROPERLY HEAT TREATED AND COULD FRACTURE AND BECOME DISPLACED WITHIN THE REAR AXLE. SHOULD THE PIN SHIFT OUT OF POSITION, IT COULD CREATE AN INTERFERENCE CONDITION AND CAUSE THE REAR AXLE TO LOCK.

Consequence & remedy

Consequence: THE DRIVER MAY NOT BE ABLE TO MAINTAIN DIRECTIONAL CONTROL OF THE VEHICLE AND A CRASH COULD OCCUR WITHOUT WARNING.

Remedy: DEALERS WILL INSTALL A NEW REAR AXLE CROSS PIN FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463 AND AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.