IllustrationTrailer brake system is blinking to much
2014 GMC Sierra 1500
Owner reports · Recalls · Investigations
More warning signs than most Sierra 1500 years
Owner complaints for the 2014 GMC Sierra 1500 are substantially higher than the model-year median of 181.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sierra 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1360–25K
8925–50K
13350–75K
7475–100K
54100–150K
25150K+
511 reports with mileage · 227 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 154 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Exterior Lighting. Review the 148 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 139 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
24 crash reports7 fire reports13 injury reports
Electrical System complaints
128 reportsIntermittent service trailer brake system messages, dealer unable to troubleshoot.
The contact owns a 2014 GMC Sierra 1500. The contact stated that while driving approximately 10 - 15 MPH with the rear defroster activated on the rear powered sliding window, there was a sizzling sound, and started smelling smoke inside the vehicle. The contact pulled over, stopped, exited the vehicle, started inspecting inside …
Read full complaint
The contact owns a 2014 GMC Sierra 1500. The contact stated that while driving approximately 10 - 15 MPH with the rear defroster activated on the rear powered sliding window, there was a sizzling sound, and started smelling smoke inside the vehicle. The contact pulled over, stopped, exited the vehicle, started inspecting inside the rear of the vehicle; and saw smoke on the driver’s side rear of the vehicle, between the window and the seatback. While the contact was bent over trying to ascertain where the smoke was coming from, the driver’s side rear window exploded. The contact poured water on the window to put out the smoke. During the explosion the contact sustained a mild concussion and severe earache that lasted for two days; however, medical attention was not needed. The Fire Department and Police Department were contacted and notified of the failure. The contact was informed by the Fire Department that the cause was an electrical system fire. The vehicle was driven to the local dealer to be diagnosed however, the cause for the failure was not yet determined. The vehicle was not yet repaired. The manufacturer was contacted regarding the failure but no assistance was offered. The VIN was not available. The approximate failure mileage was 150,000.
I was driving into a Walmart parking lot making a turn and my vehicle shut-off while I was driving….I was lucky that it wasn’t another car behind me … 2) i was turning out of my driveway and my vehicle shut off while coming out of the driveway… I live on a busy street lucky no traffic was coming
When turning 30 mph and under the eps (power steering) cuts out randomly for a second or less and jerks the wheel only causing a slight swerve so far but has me worried and I'll be paying for the software update out of pocket since my truck isn't in the recall even though other 2014 sierras are recalled.
After driving vehicle for about 40 mins from last parked location, i slowed to take a left hand turn, engaged blinker, accelerated while proceeding to turn left. the steering wheel jerked to the Right and sounded an audible "ding" and door locks engaged. upon driving an additional estimated 100 feet, the entire system shut down…
Read full complaint
After driving vehicle for about 40 mins from last parked location, i slowed to take a left hand turn, engaged blinker, accelerated while proceeding to turn left. the steering wheel jerked to the Right and sounded an audible "ding" and door locks engaged. upon driving an additional estimated 100 feet, the entire system shut down. (i happened to be turning into a parking lot where there was a car parts store in town) no power at all, nothing on the display panel, all doors remained locked and i was locked inside the vehicle. i placed the gear shift into Park and tried unlocking the doors, which would not unlock due to no power. taking the key out of the ignition and reinserting it and tried to start did nothing. after a few more failed attempts, the interior lights and display screen flashed (glitchy blinking) and after a few more attempts, when the key was turned to the run position I finally had normal power. the doors finally unlocked. seemed as if the system rebooted itself and i had power and was able to start the vehicle. the dash panel showed a message to roll down the drivers side window, then showed a message to roll up the drivers side window. after i followed the prompts, everything returned to normal. i went into the parts store and had them hook up to a code scanner, which did not show any codes, the battery, alternator, and starter were also checked and were fine. i was able to drive home with no problem. I am afraid to drive my truck because i do not want this to happen when driving at a higher rate of speed. I was fortunate to be turning into a parking lot when the event happened. I am fearful of this happening again and causing an accident.
I’m having a trail break system warning every few minutes. It is constant and beeps consistently. To the point where I almost cannot drive it. It won’t go away after a little while and is constantly turning on and off. This just recently occurred and hasn’t stopped since. Likewise there was no other indication of this happening …
Read full complaint
I’m having a trail break system warning every few minutes. It is constant and beeps consistently. To the point where I almost cannot drive it. It won’t go away after a little while and is constantly turning on and off. This just recently occurred and hasn’t stopped since. Likewise there was no other indication of this happening till about two days ago. It’s very distracting and persistent to the point where I feel like I can’t even drive with it on.
THE TRUCK JUST SHUT OFF ALL ELECTRICAL AND DASH CONTROLS AS I WENT TO TURN INTO MY DRIVEWAY. ITS DONE IT TO ME TWICE SO FAR IN THE LAST 3 WEEKS. . NO BRAKES AND NO POWER STEERING.
Driving 5 mph, error came on and truck shut off completely while still driving, I was able to start it, drove to my destination, about 10 miles away. Parked and turned off truck, came back, the truck was completely dead. replaced the battery and was fine for a month. Yesterday while pulling up to destination on low gear going sl…
Read full complaint
Driving 5 mph, error came on and truck shut off completely while still driving, I was able to start it, drove to my destination, about 10 miles away. Parked and turned off truck, came back, the truck was completely dead. replaced the battery and was fine for a month. Yesterday while pulling up to destination on low gear going slow error showed up, the engine revved high then shut down completely. EPS recall and no dates to service yet.
While fixing an exhaust leak on this vehicle, the grounding cable that attaches to the engine block appeared to be chafed, partially crushed, and exposing some copper. The grounding cable runs down the firewall of the passenger side of the vehicle, runs briefly along the frame rail, and passes underneath the exhaust manifold. Th…
Read full complaint
While fixing an exhaust leak on this vehicle, the grounding cable that attaches to the engine block appeared to be chafed, partially crushed, and exposing some copper. The grounding cable runs down the firewall of the passenger side of the vehicle, runs briefly along the frame rail, and passes underneath the exhaust manifold. There is a potential for the cable to not properly ground over time, causing unknown issues. The vehicle has not been inspected by the manufacturer or dealer as this vehicle is outside of bumper-to-bumper warranty. A support case was opened with GM, but as an individual, they will not allow me to report the issue with pictures. They require the dealer to be the reporter.
Official recalls
921V245000 · Seat Belts:front
Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
19V761000 · Electronic Stability Control (esc); Service Brakes; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
19V645000 · Service Brakes, Hydraulic:power Assist:vacuum
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
18V267000 · Equipment
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
17V437000 · Air Bags:frontal; Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seat Belts:pretensioner
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
17V414000 · Steering:electric Power Assist System
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
16V651000 · Air Bags:frontal; Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seat Belts:pretensioner
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
16V209000 · Seat Belts
Apr 12, 2016
General Motors LLC (GM) is recalling certain model year 2014-2015 Chevrolet Silverado 1500 and GMC Sierra 1500 trucks manufactured January 29, 2013, to January 21, 2015. While entering the vehicle, the seat belt tensioner cable may be positioned such that the driver slides over it. This movement may result in the fatigue and separation of the cable.
Consequence & remedy
Consequence: If the tensioner cable separates, the driver may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will modify the vehicles to prevent the tensioner from being damaged. Any tensioner that has already been damaged will be replaced, free of charge. The recall began on August 11, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 15822.
14V007000 · Engine And Engine Cooling:exhaust System
Jan 13, 2014
General Motors is recalling certain 2014 model year Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles, and 2015 model year Cadillac Escalade and Escalade ESV; Chevrolet Silverado HD; and GMC Sierra HD, Yukon, and Yukon XL, equipped with a 4.3L engine or 5.3L engine.
Consequence & remedy
Consequence: The overheated exhaust components may melt nearby plastic parts and may result in an engine fire.
Remedy: General Motors will notify owners, and dealers will reprogram the engine control module, free of charge. The recall began on January 16, 2014. Owners may contact Chevrolet at 1-800-222-1020 and GMC at 1-800-462-8782. General Motors' number for this recall is 14008.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.