NHTSA owner reports · September 18, 2026 snapshot.
Engine And Engine Cooling complaints
4 reportsClear category filter27,000 miles · Feb 17, 2015
Engine And Engine CoolingFuel/propulsion System
THE FIRST TIME WAS NOV.2014 WHEN THE CHECK ENGINE LIGHT CAME ON SOLID ALONG WITH THE TRACTION CONTROL LIGHT ENGINE POWER WAS REDUCED AND THE ENGINE VIBRATED AND WOULD NOT GO OVER 20 MPH.I LEFT THE TRUCK PARKED FOR 3 DAYS AND WHEN CRANKED THE TRUCK ALL LIGHTS WERE OFF AND THE TRUCK RAN FINE.ONCE IN DEC. 2014 AND ONCE IN JAN.2015…
Read full complaint
THE FIRST TIME WAS NOV.2014 WHEN THE CHECK ENGINE LIGHT CAME ON SOLID ALONG WITH THE TRACTION CONTROL LIGHT ENGINE POWER WAS REDUCED AND THE ENGINE VIBRATED AND WOULD NOT GO OVER 20 MPH.I LEFT THE TRUCK PARKED FOR 3 DAYS AND WHEN CRANKED THE TRUCK ALL LIGHTS WERE OFF AND THE TRUCK RAN FINE.ONCE IN DEC. 2014 AND ONCE IN JAN.2015 THE SOLID CHECK ENGINE LIGHT CAME ON BUT THE TRUCK RAN FINE AND AFTER A FEW DAYS WENT OFF. THE FIRST WEEK OF FEB. 2015 THE CHECK ENGINE AND TRACTION CONTROL LIGHT CAME ON ENGINE POWER WAS REDUCED AND ENGINE VIBRATION. I WAS ABLE TO DRIVE SLOWLY ONLY TO AN INDEPENDENT MECHANIC THAT I NORMALLY GO TO BECAUSE HE WAS CLOSER THAN THE DEALERSHIP AND I WANTED IT CHECK IMMEDIATELY SINCE THE WARNING LIGHTS WERE ON.HIS CODES SHOWED THE THROTTLE BODY WITH SENSOR NEEDED TO BE REPLACED.HE STATED HE LEFT THE CODES IN EVEN THOUGH THE WARNING LIGHTS WENT OFF BECAUSE HE THOUGHT THIS WORK WAS COVERED UNDER WARRANTY.I IMMEDIATELY CALLED THE DEALERSHIP AND THEY WANTED TO MAKE AN APPOINTMENT FOR THE FOLLOWING WEEK AND WHEN I TOLD THEM ALL THE WARNING LIGHTS HAD WENT OFF THEY STATED IT WOULD PROBABLY BE A WASTE OF TIME TO CHECK ON THEIR COMPUTER. I TOLD THE DEALERSHIP SERVICE DEPT. ABOUT HOW YOU DON'T KNOW WHEN THIS WILL HAPPEN AND WHEN IT DOES YOU ARE BASICALLY STRANDED BECAUSE THE VEHICLE WILL BARELY MOVE. THE NEXT WEEK FEB.11, 2015 IT HAPPENED AGAIN AND ALL 3 TIMES I WAS LUCKY I WAS NOT IN ALOT OF TRAFFIC OR TRAVELING AT HIGH SPEEDS OR ON A STEEP GRADE.IF I WOULD HAVE BEEN THERE MAY HAVE BEEN A ACCIDENT. I HAD TO LEAVE THE TRUCK IN A PARKING LOT AND THE NEXT DAY TOOK IT BACK TO THE INDEPENDENT MECHANIC.I CALLED THE DEALERSHIP AND AGAIN THEY WANTED TO MAKE AN APPOINTMENT AND THEY STATED THE WORK WAS NOT COVERED UNDER WARRANTY SO MY MECHANIC CAME UP WITH THE SAME CODES AND FIXED THE PROBLEM.CALLED GM AND EXPLAINED THE UNSAFE SITUATION AND GOT NO CUSTOMER SERVICE. *TR
NHTSA ODI #10683864
35,000 miles · Nov 13, 2012
Engine And Engine CoolingVisibility
THE WINDSHIELD AND THE SIDE WINDOWS OF MY NEW 2010 GMC SIERRA 1500 WT, HAVE AN EXTREME TENDENCY TO FOG OVER IN TEMPERATURES NEAR THE FREEZING POINT. I HAVE READ, AND OBSERVED, THAT THE AC COMPRESSOR BECOMES AUTOMATICALLY DISABLED WHEN THE OUTSIDE TEMPERATURE GETS NEAR THE FREEZE ZONE (I THINK THE ACTUAL THRESHOLD IS SOMEWHERE AR…
Read full complaint
THE WINDSHIELD AND THE SIDE WINDOWS OF MY NEW 2010 GMC SIERRA 1500 WT, HAVE AN EXTREME TENDENCY TO FOG OVER IN TEMPERATURES NEAR THE FREEZING POINT. I HAVE READ, AND OBSERVED, THAT THE AC COMPRESSOR BECOMES AUTOMATICALLY DISABLED WHEN THE OUTSIDE TEMPERATURE GETS NEAR THE FREEZE ZONE (I THINK THE ACTUAL THRESHOLD IS SOMEWHERE AROUND 40 DEGREES F). WITH THE AC DISABLED, THE DEFROST MODE CANNOT KEEP THE WINDOWS CLEAR. THE PROBLEM IS MAGNIFIED WHEN THERE ARE TWO OR THREE INDIVIDUALS IN THE CAB. AT THAT POINT, IT IS EXCEEDINGLY DIFFICULT TO CLEAR THE SIDE WINDOWS, EVEN TO THE POINT THAT FROST FORMS ON THE INSIDE WINDOW SURFACE! VERY RECENTLY, WHILE TRAVELING TO WORK DURING MY 40 MILE COMMUTE, I WAS RUNNING THE AC, WITH THE TEMP CONTROL SET TO A COMFORTABLE LEVEL AND THE BLOWER ABOUT THE MEDIUM SETTING AND FLOWING THROUGH THE MAIN VENTS. THE OUTSIDE TEMPERATURE WAS, APPARENTLY, HOVERING NEAR THE POINT WHERE THE ELECTRONICS DISABLE THE COMPRESSOR. THE WINDSHIELD AND BOTH SIDE WINDOWS FOGGED OVER SUDDENLY. I NOTICED THE AC LIGHT WAS OUT, SO I SWITCHED TO DEFROST MODE AND HI BLOWER. THE WINDSHIELD DID CLEAR IN ABOUT A MINUTE OR TWO, BUT ALL OF THAT HAPPENED WHILE DRIVING DOWN THE TURNPIKE AT 70 MPH. THIS SEEMS TO BE A SIGNIFICANT SAFETY CONCERN....AT LEAST FOR ME AND MY FAMILY. IF THE AC COMPRESSOR HAD STAYED ENABLED, THIS WOULD NEVER HAVE HAPPENED. IT IS VERY DIFFICULT TO STOP CONDENSATION BUILDUP IF YOU CANNOT RUN THE AC TO DRY THE CABIN AIR. THIS DESIGN CONFIGURATION SEEMS TO PRESENT AN ISSUE OF SAFETY. I AM NOT SURE IF IT IS JUST THIS PARTICULAR MODEL. I SUSPECT SO, SINCE IT IS THE BASE MODEL TRUCK. WE HAVE A 2011 GMC TERRAIN, WHICH DOES NOT PRESENT THIS ISSUE. I HAVE CONTACTED THE DEALER ABOUT THIS ISSUE NOW FOR 3 YEARS WITH NO RESOLUTION. THEY ACT AS THOUGH YOU ARE AN IDIOT. *TR
NHTSA ODI #10484089
5,000 miles · Dec 27, 2011
Engine And Engine Cooling
TL* THE CONTACT OWNS A 2010 GMC SIERRA 1500. THE CONTACT STATED THAT WHEN THE PISTONS WERE LOOSE AND STRUCK THE CYLINDER WALL, IT WOULD LOOSEN UP THE ENGINE AND CAUSED AN ABNORMAL KNOCKING FROM THE ENGINE. THE DEALER WAS NOTIFIED OF THE FAILURE WHO ADVISED THE CONTACT THAT THE FAILURE WAS NOTHING TO BE CONCERNED ABOUT AND WAS NO…
Read full complaint
TL* THE CONTACT OWNS A 2010 GMC SIERRA 1500. THE CONTACT STATED THAT WHEN THE PISTONS WERE LOOSE AND STRUCK THE CYLINDER WALL, IT WOULD LOOSEN UP THE ENGINE AND CAUSED AN ABNORMAL KNOCKING FROM THE ENGINE. THE DEALER WAS NOTIFIED OF THE FAILURE WHO ADVISED THE CONTACT THAT THE FAILURE WAS NOTHING TO BE CONCERNED ABOUT AND WAS NOT HURTING THE ENGINE. THE MANUFACTURER WAS NOTIFIED WHO STATED TO THE CONTACT THAT THEY WOULD SPEAK WITH THE DEALER TO DETERMINE THE REMEDY FOR THE FAILURE. THERE WERE NO RECALLS FOR THE FAILURE. THE FAILURE MILEAGE WAS 5,000 AND THE CURRENT MILEAGE WAS 24,000. UPDATED 01/10/12*LJ
NHTSA ODI #10441314
53,920 miles · Oct 25, 2010
Engine And Engine Cooling
2004 GMC SIERRA WITH 5.3L ENGINE. AT 53,920 MILES BEGAN TICKING AT COLD START UP. CONFIRMED BY GMC DEALER TODAY THAT CYLINDER HEAD HAS CRACK WHICH CAUSED COOLANT TO SEEP INTO ENGINE OIL. $3,800 TO REPLACE DEFECTIVE CYLINDER HEADS AND INSTALL NEW LIFTERS. TECHNICAL SERVICE BULLETIN # 06-06-01-019B. THE CYLINDER HEADS IN THI…
Read full complaint
2004 GMC SIERRA WITH 5.3L ENGINE. AT 53,920 MILES BEGAN TICKING AT COLD START UP. CONFIRMED BY GMC DEALER TODAY THAT CYLINDER HEAD HAS CRACK WHICH CAUSED COOLANT TO SEEP INTO ENGINE OIL. $3,800 TO REPLACE DEFECTIVE CYLINDER HEADS AND INSTALL NEW LIFTERS. TECHNICAL SERVICE BULLETIN # 06-06-01-019B. THE CYLINDER HEADS IN THIS ENGINE ARE MANUFACTURED BY "CASTECH". *TR
NHTSA ODI #10362337
Official recalls
4Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration