2014 Gillig Low Floor

Consequence: The engine may be started unexpectedly, increasing the risk of injury to anyone nearby the engine compartment during maintenance operations.

Remedy: Dealers will update the software for the buses equipped with the Vanner Ultracapacitor system, and conduct a hard rewire for the buses equipped with the KBI system, free of charge. Owner notification letters were mailed on June 22, 2022. Owners may contact Gillig's customer service at 1-510-264-5073 for 1-800-735-1500.

Consequence: A loss of power steering assist may increase the risk of crash.

Remedy: Gillig will notify owners, and dealers will replace the motor-pump assemblies, free of charge. The recall began August 13, 2020. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: With the improper circuit breaker rating, an electrical short in either of these circuits may increase the risk of a fire.

Remedy: Gillig will notify owners, and dealers will replace the circuit breakers, free of charge. The recall began April 24, 2020. Owners may contact Gillig customer service at 1-510-264-5073 or 1-800-735-1500.

Consequence: A loss of headlights can reduce the driver's ability to see, increasing the risk of a crash.

Remedy: Gillig has notified owners, and dealers will install new back covers on the headlight buckets, free of charge. The recall began April 1, 2019. Owners may contact Gillig customer service at 1-510-264-5073 or 1-800-735-1500.

Consequence: Loose cage bolts may result in the bus rolling away when in the park position or a loss of braking ability if the service brake air pressure is lost while moving. Either condition may increase the risk of a crash.

Remedy: Gillig will notify owners, and dealers will tighten the spring cage bolts, free of charge. The recall began December 10, 2018. Owners may contact Gillig customer service at 1-510-264-5073 or 1-800-735-1500.

Consequence: The mismatched flashing may confuse other drivers, increasing the risk of a crash.

Remedy: Gillig will notify the owner of the buses, and dealers will reprogram the turn signals with new software, free of charge. The recall began August 30, 2018. Owners may contact Gillig customer service at 1-510-264-5073 or 1-800-735-1500.

Consequence: The reduced visibility of the turn signals can increase the risk of a crash.

Remedy: Gillig will notify owners, and dealers will update the software that controls the turn flash rate, free of charge. The recall began on August 2, 2018. Owners may contact Gillig customer service at 1-510-264-5073 or 1-800-735-1500.

Consequence: A loss of power steering assist will cause the need for increased steering effort, increasing the risk of a crash.

Remedy: Gillig will notify owners, and dealers will replace the steering motor-pump assemblies, free of charge. The recall began on October 24, 2017. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: The reduced visibility of the turn signals may increase the risk of a crash.

Remedy: Gillig will notify owners, and dealers will install turn signals that have increased visibility. The recall began June 7, 2019. Owners may contact Gillig customer service at 1-510-264-5073 or 1-800-735-1500.

Consequence: A frayed hose may leak air, causing the rear brake(s) to lock up unexpectedly, or fail to operate when the brakes are applied. Either scenario increases the risk of a crash.

Remedy: Gillig will provide fleets new rear brake hoses, fittings, clamps, and hardware along with instructions on how to reorient the hoses using the new fittings, and reimburse them for their labor, free of charge. The recall began on September 29, 2016. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: Flashing brake lights may cause confusion to other drivers, increasing the risk of a crash.

Remedy: Gillig will notify owners, and dealers will install a new software update, free of charge. The recall began on July 2016. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the seatbelt anchorage assembly separates from the J-Bracket, the bus driver may not be properly restrained in the event of a crash increasing their risk of injury.

Remedy: Gillig will notify the owners, and dealers will inspect the seats to determine if welds are missing. Any J-Bracket that is missing welds will be removed and replaced, free of charge. The recall began on March 1, 2016. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: Corrosion, part deterioration, or frozen water in the brake chamber may reduce braking ability, increasing the risk of a crash.

Remedy: Gillig will notify owners and the brake chambers will be replaced free of charge. The recall began on March 1, 2016. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the electrical power cable rubs against the injector fuel line, the cable may short circuit or the fuel line may leak fuel. Either possibility increases the risk of a fire.

Remedy: Gillig will notify owners, and dealers will inspect the grid heater power cable/hard injector fuel line for wear, and will properly route and support the grid heater power cable, free of charge. The recall began on July 17, 2015. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the bracket is inadequately bonded, it may detach from the body, preventing the stop and turn lights from being visible to following vehicles, increasing the risk of a crash.

Remedy: Gillig has notified owners. Gillig will inspect the taillight brackets to verify that they are properly bonded to the body. Brackets that are not properly bonded will be removed and properly bonded to the vehicle, free of charge. The recall began on June 12, 2015. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Remedy: Gillig will notify owners, and dealers will secure the ends of the 90-degree elbow. In addition, the electronic control module (ECM) will be reprogrammed with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 2, 2015. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the front brake hoses rub the air bag suspension tower, a hole may develop and the resulting air leak may reduce the brake air pressure, lengthening the distance needed to stop the transit bus and increasing the risk of a crash.

Remedy: Gillig has notified owners, and dealers will replace the brake hoses with shorter ones that will not contact the suspension tower, free of charge. The recall began on April 28, 2015. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the primary and secondary air brake supply lines from the tanks to the brake valve are crossed and the vehicle loses pressure in the primary tank, the vehicle service brake system performance may be reduced. In the case of a total loss of primary tank air pressure, the service brake system will not function. If the service brake system does not function or performance is reduced, an application of the brake pedal by the vehicle operator may not slow or stop the vehicle as expected, increasing the risk of a crash.

Remedy: Gillig will notify owners, and dealers will correct the installation of the primary and secondary brake supply lines, free of charge. The recall began on October 17, 2014. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the engine stalls unexpectedly there is an increased risk of a crash.

Remedy: Cummins will notify owners on behalf of Gillig, and Cummins service centers will replace the fuel filter, free of charge. The recall began on September 16, 2014. Owners may contact Gillig at 1-510-785-1500 or Cummins customer service at 1-812-377-3713.

Consequence: If the bus's anti-lock brake system was non-functioning and the bus experienced a significant braking event that when combined with the road conditions may lock the rear brakes, then a delay in brake release timing could result in a lock up of the rear wheels, increasing the risk of crash.

Remedy: Gillig will notify owners, and dealers will install a quick release valve, free of charge. The recall began on September 15, 2014. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the sampling hose leaks oil in the presence of hot engine engine exhaust components, there is an increased risk of fire.

Remedy: Gillig will notify owners, and dealers will inspect the oil sampling hose. If the hose is routed too closely, the hose will be removed, replaced and rerouted to provide appropriate clearance of the hot components. The recall is expected to begin in early August 2014. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: If the terminals corrode, there may be an intermittent electrical connection and possibly cause disruption or loss of the J1939 communication, resulting in interruptions of the engine, transmission, ABS and body controllers, increasing the risk of a crash.

Remedy: Gillig will notify owners, and dealers will replace the overmold connector, and install heat shrink tubing on the connector/cable junction, free of charge. The recall began in June 2014. Owners may contact Gillig customer service at 1-800-735-1500.

Consequence: The improper operation of the sensor could induce elevated exhaust temperatures or flames from the exhaust pipe, increasing the risk of a vehicle fire.

Remedy: Cummins Inc. and Cummins Wesport Inc. will notify owners, and dealers will upload a new ECM calibration, free of charge. The recall began on March 20, 2014. Owners may contact Gillig LLC at 1-510-785-1500 or Cummins Inc. at 1-800-343-7357.