Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 1 of 1 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Power Train. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Service Brakes. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Vehicle Speed Control. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
1 reports
40,400 miles · Mar 1, 2021
Power TrainService BrakesVehicle Speed Control
WHILE DRIVING USING CRUISE CONTROL, THE SPEED WAS INCREASING 15 MPH PAST THE SETTING. I WAS ABLE TO STOP BY USING THE BRAKE. THEN ALL THE WARNING LIGHTS CAME ON. AFTER THAT IT WOULDN'T SHIFT RIGHT, IT WOULDN'T SHIFT INTO A HIGH GEAR AND IT WOULD BE HARD TO GET MOVING FROM A STOP. I HAD TO DRIVE TO A DEALER SEVERAL HUNDRED MILES …
Read full complaint
WHILE DRIVING USING CRUISE CONTROL, THE SPEED WAS INCREASING 15 MPH PAST THE SETTING. I WAS ABLE TO STOP BY USING THE BRAKE. THEN ALL THE WARNING LIGHTS CAME ON. AFTER THAT IT WOULDN'T SHIFT RIGHT, IT WOULDN'T SHIFT INTO A HIGH GEAR AND IT WOULD BE HARD TO GET MOVING FROM A STOP. I HAD TO DRIVE TO A DEALER SEVERAL HUNDRED MILES AND IT WAS QUITE HARROWING. OF COURSE THEY COULDN'T WORK ON IT FOR 3 DAYS SO WE RENTED A CAR TO GO BACK HOME 400 MILES. THE PROBLEM WAS A REAR WHEEL SPEED SENSOR. THIS WAS THE SECOND TIME IT HAPPENED IN LESS THAN 5 MONTHS, ONCE IN VIRGINIA WITH 36410 MILES ON IT AND AGAIN IN NEBRASKA WITH 40621 MILES. IT CREATES A DANGEROUS SITUATION BECAUSE SOMETIMES THERE IS NO SHOULDER AND CAN NOT DRIVE FAST ENOUGH FOR THE TRAFFIC BEHIND. THE PROBLEM BOTH TIMES WERE REAR WHEEL SPEED SENSORS.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2012-2018 Mercedes Benz Sprinter 3500 and Freightliner Sprinter 3500 vehicles upfitted into campers or recreational vehicles. The Electronic Stability Control (ESC) unit may become disabled on these vehicles.
Consequence & remedy
Consequence: If ESC becomes disabled, vehicle driving stability may be impacted under certain driving conditions, increasing the risk of a crash.
Remedy: DVUSA will notify owners, and dealers will replace the rear-wheel speed sensor with a more robust sensor, free of charge. DVUSA issued owners an interim notification on March 10, 2021. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this recall is NC3DREZAHA.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2015-2020 Mercedes Benz Sprinter and Freightliner Sprinter vehicles. The hydraulic power steering return line hoses may detach at their connection points under certain operating conditions, causing hydraulic fluid to leak.
Consequence & remedy
Consequence: The sudden loss of power steering assist and hydraulic steering fluid leaking onto the roadway may increase the risk of a crash.
Remedy: DVUSA will notify owners, and dealers will check the return line connections of the power steering system, correcting it as needed, free of charge. The recall began December 23, 2020. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this campaign is NV3LETULPE.
Midway Specialty Vehicles (Midway) is recalling one 2016 Freightliner Sprinter vehicle modified to be equipped with a Ricon Titanium Wheelchair Lift. The wheelchair lift positioning input cam may fail while the lift is in use, allowing the platform to travel higher than the vehicle's floor height. As such, this vehicle fails to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 403, "Platform Lift Systems."
Consequence & remedy
Consequence: If the wheelchair lift platform stops above the vehicle floor, the wheelchair user can tip inwards towards the vehicle when exiting the lift, increasing their risk of injury.
Remedy: Midway has notified the affected owner and a Ricon dealer will replace the lift positioning input cam, free of charge. The recall began February 27, 2019. Owners may contact Ricon customer service at 1-800-322-2884 or Midway customer service at 1-574-264-2530.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2015-2017 Freightliner Sprinter 2500 and 3500 and Mercedes-Benz Sprinter 2500 and 3500 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the driver frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the driver frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: DVUSA will notify owners, and dealers will replace the front driver air bag module, free of charge. The recall is began March 15, 2019. Owners may contact DVUSA customer service at 1-877-762-8267.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2014-2017 Freightliner Sprinter 2500 and 3500 and Mercedes-Benz Sprinter 2500 and 3500 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: DVUSA will notify owners, and dealers will replace the front passenger air bag module, free of charge. The recall began March 15, 2019. Owners may contact DVUSA customer service at 1-877-762-8267.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2016 Mercedes-Benz Sprinter 2500 and 3500 vehicles and Freightliner Sprinter 2500 and 3500 vehicles. The bracket for the center support bearing of the drive shaft may not have been properly welded.
Consequence & remedy
Consequence: If the event of a crash, the bracket may detach and the drive shaft may damage the fuel system, increasing the risk of a fire.
Remedy: DVUSA will notify owners and dealers will install three additional rivets to secure the bracket, free of charge. Interim notices informing owners of the safety risk were mailed on May 5, 2017. The recall began on July 7, 2017. Owners may contact DVUSA customer service at 1-877-762-8267.
Daimler Vans USA, LLC (DVUSA) is recalling certain 2013-2016 Mercedes-Benz Sprinter 2500 and 3500 and Freightliner Sprinter 2500 and 3500 vans. These vehicles were manufactured without a reinforcement plate and protective bracket on the air bag control unit. As a result, the air bag control unit may not remain functional after the initial impact, possibly preventing additional air bags from deploying in response to a secondary impact.
Consequence & remedy
Consequence: If additional air bags do not deploy as intended, the occupants are at an increased risk of injury.
Remedy: DVUSA will notify owners, and dealers will install a reinforcement plate and protective bracket around the air bag control unit, free of charge. The recall began on May 26, 2017. Owners may contact DVUSA customer service at 1-877-762-8267.
Daimler Vans USA, LLC (DVUSA) is recalling certain model year 2016 Mercedes-Benz and Freightliner Sprinter 2500 and 3500 vehicles manufactured March 1, 2016, to May 31, 2016. The bolts connecting the lower seat belt connection to the rear bench seat may not have been properly tightened.
Consequence & remedy
Consequence: If the bolts were not properly tightened, the seat belt may fail to secure the seat occupant in the event of a crash.
Remedy: DVUSA will notify owners, and Sprinter dealers will inspect the connecting bolts, tightening them as necessary, free of charge. The recall began on November 18, 2016. Owners may contact DVUSA customer service at 1-877-762-8267.
Daimler Vans USA, LLC (DVUSA) is recalling certain model year 2015-2016 Mercedes-Benz Sprinter 2500 and 3500 vehicles manufactured May 31, 2015, to April 30, 2016, and 2015-2016 Freightliner Sprinter 2500 and 3500 vehicles manufactured May 1, 2015, to April 30, 2016. The affected vehicles are configured to have super-high roofs, but may not be equipped with the required crash pads.
Consequence & remedy
Consequence: If the required crash pads are missing, it can increase the risk of injury to a front passenger seat occupant if they are unbelted.
Remedy: DVUSA will notify owners, and dealers will install the required crash-pads, free of charge. The recall began on August 11, 2016. Owners may contact DVUSA customer service at 1-877-762-8267.
Daimler Vans USA, LLC (DVUSA) is recalling certain model year 2015-2016 Mercedes Benz and Freightliner Sprinter 2500 and 3500 vehicles manufactured April 1, 2015, to October 31, 2015. The affected vehicles may have had multiple layers of paint applied, and as a result, in a crash, the windows may separate from the vehicle when the outer layer of paint peels from the layer below.
Consequence & remedy
Consequence: If the windows separate from the vehicle in a crash, the occupants are at a greater risk of injury.
Remedy: DVUSA will notify owners, and dealers will remove the windows and inspect the paintwork, repainting the vehicles as necessary, free of charge. This recall began August 4, 2016. Owners may contact DVUSA customer service at 1-770-705-2070.
Daimler Vans USA, LLC (DVUSA) is recalling certain model year 2015-2016 Mercedes-Benz and Freightliner Sprinter 2500 and 3500 vans manufactured April 29, 2015, to December 15, 2015. The affected vehicles have a tire pressure label that incorrectly states a higher maximum load capacity than the vehicle is designed for.
Consequence & remedy
Consequence: The vehicle may be overloaded if loaded to the incorrect weight shown on the label, possibly resulting in axle or tire failure, increasing the risk of a crash.
Remedy: DVUSA will notify owners, and Mercedes-Benz and Freightliner dealers will replace the incorrect tire pressure label, free of charge. The recall began March 2016. Owners may contact DVUSA customer service at 1-877-762-8267.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2016 Freightliner Sprinter 3500 Problems, Complaints & Recalls | Skip That Year
Illustration