NHTSA owner reports · September 18, 2026 snapshot.
NHTSA investigations
4DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA17004 · Power Steering Failure
Opened Nov 20, 2017 · Closed Feb 9, 2024
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:rack And Pinion; Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (4)
Steering:electric Power Assist System
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur
Illustration