NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
508 reportsMileage unknown · Sep 10, 2026
Electrical SystemService Brakes
I own a 2010 Ford Fusion Hybrid and am reporting a recurring and serious braking problem. On XXX, while driving to pick up my mom and my [XXX] son, I pressed the brake pedal to stop, but the vehicle did not stop normally. I repeatedly tried to brake, but the vehicle took much longer to stop than it should have. The brake pedal b…
Read full complaint
I own a 2010 Ford Fusion Hybrid and am reporting a recurring and serious braking problem. On XXX, while driving to pick up my mom and my [XXX] son, I pressed the brake pedal to stop, but the vehicle did not stop normally. I repeatedly tried to brake, but the vehicle took much longer to stop than it should have. The brake pedal became spongy and did not have normal resistance. The BRAKE, ABS, and AdvanceTrac warning lights appeared. The vehicle’s computer/system was reset afterward, and the vehicle drove normally for several days. On XXX, the same braking problem happened again while i was driving to go pick up my [XXX] son from school. The brake pedal became spongy, and repeatedly pumping the brakes did not properly stop the vehicle. This time I had to use the emergency/parking brake to help bring the vehicle to a stop. The same BRAKE, ABS, and AdvanceTrac warning lights appeared.After this incident, the rear brakes were replaced and a new ABS Anti-Lock Brake Pump (part number 9E58-2C555-AF) was installed. The computer/system was also reset again. On XXX, the BRAKE, ABS, and AdvanceTrac warning lights came back on again despite the new brake components and computer reset. The mechanic who performed the repairs has been unable to determine the cause, so the vehicle is being taken to another repair shop for further diagnosis. I am concerned that this may be a safety defect involving the braking/ABS system of the 2010 Ford Fusion Hybrid. The vehicle has experienced an actual loss of braking ability, including an incident where I had to use the emergency/parking brake to stop. I am requesting that NHTSA investigate this issue. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11763255
Mileage unknown · Aug 16, 2026
Visibility/wiper
2020 Ford Escape wipers keep stuttering, moving very slowly, freezing midway through cycle, or fail to operate during adverse weather conditions. This results in poor to no visibility sometimes with the wiper blocking vision directly. This is a known recall and Ford has refused to repair the wiper until the unveil their solution…
Read full complaint
2020 Ford Escape wipers keep stuttering, moving very slowly, freezing midway through cycle, or fail to operate during adverse weather conditions. This results in poor to no visibility sometimes with the wiper blocking vision directly. This is a known recall and Ford has refused to repair the wiper until the unveil their solution for all potentially impacted vehicles. They acknowledge that a wiper motor would repair our vehicle right now but told us to wait for months while they determine a global fix. Recall number we believe is 26S14. Both Ford America and local dealer will not perform work. Communications were via phone call with both dealer and Ford America.
NHTSA ODI #11757251
Mileage unknown · Aug 14, 2026
Steering
The power steering has failed twice recently while driving and the dashboard warning displayed as follows: power steering assist fault. This makes it very hard to steer, dangerous and scary when this happens. Can a recall be issued for my vehicle? I am very disappointed that my 2010 ford fusion hybrid vehicle was left out of th…
Read full complaint
The power steering has failed twice recently while driving and the dashboard warning displayed as follows: power steering assist fault. This makes it very hard to steer, dangerous and scary when this happens. Can a recall be issued for my vehicle? I am very disappointed that my 2010 ford fusion hybrid vehicle was left out of the recall even though it was manufactured at the same plant as the 2011 - 2013 models that were recalled. I found this online: Investigation and Recall ContextFederal Probes: The NHTSA investigated 2010–2012 Ford Fusion and Lincoln MKZ models for sudden loss of electric power steering, logging thousands of complaints.Exclusion of the 2010 Model: Ford issued recalls (such as campaign 15S18) for 2011–2013 models to update power steering control modules or fix motor sensor faults, leaving 2010 models uncovered by the official action.Closure: The NHTSA officially closed its investigation into the 2010 Fusion steering complaints after concluding the failure trend did not warrant a mandatory safety recall, noting drivers could still revert to manual steering.
NHTSA ODI #11757063
Mileage unknown · Jul 27, 2026
Service Brakes
SUBJECT: Fraudulent Recall Completion / Incomplete Remedy resulting in Component Failure (Recall 19S54 / NHTSA 19V904) I am writing to file an emergency safety complaint regarding a fraudulently cleared safety recall on my 2010 Ford Fusion Hybrid. According to Ford's internal OASIS database, Safety Recall 19S54 (NHTSA Campaig…
Read full complaint
SUBJECT: Fraudulent Recall Completion / Incomplete Remedy resulting in Component Failure (Recall 19S54 / NHTSA 19V904) I am writing to file an emergency safety complaint regarding a fraudulently cleared safety recall on my 2010 Ford Fusion Hybrid. According to Ford's internal OASIS database, Safety Recall 19S54 (NHTSA Campaign 19V904) was marked as "completed" under a previous owner. However, physical inspection of the vehicle proves that the mandatory federal remedy was never executed. The master cylinder still retains the original factory DOT 3 cap, and the system was never upgraded to DOT 4 fluid. Because the servicing dealership falsified the repair documentation and left the corrosive DOT 3 fluid in the system, my vehicle has now suffered the exact catastrophic safety failure the recall was meant to prevent. The ABS Hydraulic Control Unit (HCU) internal valves have seized. The brake pedal is heavily compromised, and the vehicle is an active, severe safety hazard to drive. I am the second owner of this vehicle. I unknowingly purchased a car with a fraudulently cleared safety defect. Because this failure is a direct result of an incomplete federal safety recall remedy, I demand that Ford Corporate reopen this VIN file under "Related Damage / Incomplete Remedy." I require Ford to: 1. Arrange a complimentary tow to a certified Ford dealership. 2. Replace the ruined ABS/HCU module entirely free of charge. 3. Perform the mandatory DOT 4 pressure flush and install the correct reservoir cap. 4. Provide a complimentary rental car while this safety hazard is being resolved. I have taken photographic and video evidence of the DOT 3 cap and the failed braking system to support my legal claims. Fairway Ford of Yorba Claimed it had already been done when clearly it hasn't and pushed it off like nothing.
NHTSA ODI #11753024
Mileage unknown · Jul 2, 2026
Service Brakes
Abs module failed
NHTSA ODI #11748073
Mileage unknown · Jun 16, 2026
Electrical SystemSeatsService Brakes
There have been many recalls on the 2010 Ford Fusion Hybrid, according to Ford mine has already had the repairs done yet the issues I’ve been having all match recalls. I’ve had issues with my passenger seat, the air bag system light is always on and the seat controls no longer work. The clockspring system is pure trash, there is…
Read full complaint
There have been many recalls on the 2010 Ford Fusion Hybrid, according to Ford mine has already had the repairs done yet the issues I’ve been having all match recalls. I’ve had issues with my passenger seat, the air bag system light is always on and the seat controls no longer work. The clockspring system is pure trash, there is no reason I’ve had to replace it twice now in the 2 months I’ve had this car. My ABS system keeps going in and out and says service advancetrac system. My hybrid battery rarely goes into hybrid anymore causing my mpg to drop. There were a few other things but that’s what’s coming out mind now.
NHTSA ODI #11744392
100,000 miles · Apr 8, 2025
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that upon coming to a complete stop, the brake pedal suddenly depressed all the way to the floorboard. The contact became aware that the brakes were no longer functioning properly. The vehicle returned to normal functionality, but the failure became a regular occurre…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that upon coming to a complete stop, the brake pedal suddenly depressed all the way to the floorboard. The contact became aware that the brakes were no longer functioning properly. The vehicle returned to normal functionality, but the failure became a regular occurrence. The ABS and traction control warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic). The manufacturer was notified of the failure, and a case was opened. The failure mileage was 100,000.
NHTSA ODI #11653520
150,000 miles · Apr 1, 2025
Steering
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while reversing into a parking space at 2 MPH, the vehicle lost power steering functionality, and the steering wheel became significantly difficult to turn. The contact could not recall whether a warning light was illuminated. The contact was able to park the vehicle…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while reversing into a parking space at 2 MPH, the vehicle lost power steering functionality, and the steering wheel became significantly difficult to turn. The contact could not recall whether a warning light was illuminated. The contact was able to park the vehicle. The vehicle was taken to Tire Kingdom, where it was diagnosed. The mechanic determined that the failure was related to Ford Campaign Number: 15S18. The dealer was contacted and informed the contact that the VIN was not included in the campaign. The vehicle was not repaired. The manufacturer was notified of the failure and a case was filed. The failure mileage was approximately 150,000.
NHTSA ODI #11651967
162,000 miles · Mar 18, 2025
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving 15 MPH and depressing the brake pedal, the brake pedal went to the floorboard. The contact stated that the brake system, ABS, and traction control warning lights were illuminated. Additionally, the message "Brake System Failure" was displayed. The …
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving 15 MPH and depressing the brake pedal, the brake pedal went to the floorboard. The contact stated that the brake system, ABS, and traction control warning lights were illuminated. Additionally, the message "Brake System Failure" was displayed. The contact drove with caution to the residence, and then had the vehicle towed to an independent mechanic to be diagnosed. The contact was informed that further diagnostic testing was needed to determine the cause of the failure. The vehicle was not repaired. The contact referenced NHTSA Campaign Number: 19V904000 (SERVICE BRAKES, HYDRAULIC) as a possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 162,000.
NHTSA ODI #11648973
42,000 miles · Mar 12, 2025
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving at an undisclosed speed, the message "ABS fault Detected" was displayed, prompting the contact to discontinue driving the vehicle. The ABS warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving at an undisclosed speed, the message "ABS fault Detected" was displayed, prompting the contact to discontinue driving the vehicle. The ABS warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with the ABS Hydraulic Control Unit (HCU). The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 42,000. See DP26004 for potential Defect Petition DP26004
NHTSA ODI #11647929
NHTSA investigations
6DP26004 · Anti-lock Brake System (abs) Malfunction Indicator Lamp (mil) Illuminated
Opened Apr 9, 2026 · No close date supplied
Status: open (inferred from source dates) · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
The Office of Defects Investigation (ODI) received a petition on December 22, 2025, requesting a defect investigation into the hydraulic control unit (HCU) for the Anti-lock Braking System (ABS) on the MY 2010 Ford Fusion Hybrid. The petition alleges that an illuminated ABS MIL is associated with a failure of the ABS HCU, resulting in ABS malfunction, loss of traction and electronic stability control functions, and reduced braking performance, particularly on slippery road surfaces. A defect petition has been opened to evaluate the issue and determine whether to grant or deny the petition.The petition can be reviewed at NHTSA.gov under ODI number 11647929.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
EA17004 · Power Steering Failure
Opened Nov 20, 2017 · Closed Feb 9, 2024
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:rack And Pinion; Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (4)
Steering:electric Power Assist System
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE16011 · Power Steering Failure
Opened Sep 28, 2016 · Closed Dec 25, 2017
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Additional source detail variants (2)
Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Steering
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Illustration