NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes, Hydraulic complaints
18 reportsClear category filter100,000 miles · Apr 8, 2025
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that upon coming to a complete stop, the brake pedal suddenly depressed all the way to the floorboard. The contact became aware that the brakes were no longer functioning properly. The vehicle returned to normal functionality, but the failure became a regular occurre…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that upon coming to a complete stop, the brake pedal suddenly depressed all the way to the floorboard. The contact became aware that the brakes were no longer functioning properly. The vehicle returned to normal functionality, but the failure became a regular occurrence. The ABS and traction control warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic). The manufacturer was notified of the failure, and a case was opened. The failure mileage was 100,000.
NHTSA ODI #11653520
162,000 miles · Mar 18, 2025
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving 15 MPH and depressing the brake pedal, the brake pedal went to the floorboard. The contact stated that the brake system, ABS, and traction control warning lights were illuminated. Additionally, the message "Brake System Failure" was displayed. The …
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving 15 MPH and depressing the brake pedal, the brake pedal went to the floorboard. The contact stated that the brake system, ABS, and traction control warning lights were illuminated. Additionally, the message "Brake System Failure" was displayed. The contact drove with caution to the residence, and then had the vehicle towed to an independent mechanic to be diagnosed. The contact was informed that further diagnostic testing was needed to determine the cause of the failure. The vehicle was not repaired. The contact referenced NHTSA Campaign Number: 19V904000 (SERVICE BRAKES, HYDRAULIC) as a possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 162,000.
NHTSA ODI #11648973
42,000 miles · Mar 12, 2025
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving at an undisclosed speed, the message "ABS fault Detected" was displayed, prompting the contact to discontinue driving the vehicle. The ABS warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving at an undisclosed speed, the message "ABS fault Detected" was displayed, prompting the contact to discontinue driving the vehicle. The ABS warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with the ABS Hydraulic Control Unit (HCU). The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 42,000. See DP26004 for potential Defect Petition DP26004
NHTSA ODI #11647929
160,000 miles · Feb 13, 2025
Service Brakes, HydraulicTraction Control System
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving at approximately 20 MPH, the "Check Brake System" message was displayed on the instrument panel and the brakes failed to engage while the brake pedal was depressed. The contact stated that upon depressing the brake pedal to the floorboard, the vehicle r…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving at approximately 20 MPH, the "Check Brake System" message was displayed on the instrument panel and the brakes failed to engage while the brake pedal was depressed. The contact stated that upon depressing the brake pedal to the floorboard, the vehicle responded as needed. The ABS and traction control warning lights were illuminated. The vehicle was taken back to the residence. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 160,000.
NHTSA ODI #11642576
200,000 miles · Jan 22, 2025
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while reversing at an undisclosed speed, the brake pedal was depressed and went to the floorboard. The vehicle failed to stop immediately until the parking brake was applied. The brake warning light was illuminated, and an unknown message was displayed. The vehi…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while reversing at an undisclosed speed, the brake pedal was depressed and went to the floorboard. The vehicle failed to stop immediately until the parking brake was applied. The brake warning light was illuminated, and an unknown message was displayed. The vehicle was towed to Pep Boys, who related the failure to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic); however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 200,000.
NHTSA ODI #11637707
106,000 miles · Oct 30, 2024
Service BrakesService Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving 20 MPH, the brakes became inoperable. The contact had to slam on the brake pedal for the vehicle to stop. The Service Advance-trac, brakes, and check brake system messages were displayed. The contact researched online and discovered NHTSA Campaign Numbe…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving 20 MPH, the brakes became inoperable. The contact had to slam on the brake pedal for the vehicle to stop. The Service Advance-trac, brakes, and check brake system messages were displayed. The contact researched online and discovered NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic); however, the VIN was not included. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 106,000.
NHTSA ODI #11622752
162,000 miles · Oct 24, 2024
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving in a park lot and attempting to stop the vehicle, the brake pedal was depressed; however, the vehicle failed to respond. The contact stated that the brake pedal traveled to the floorboard. The vehicle was driven to the dealer where it was diagnosed…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated that while driving in a park lot and attempting to stop the vehicle, the brake pedal was depressed; however, the vehicle failed to respond. The contact stated that the brake pedal traveled to the floorboard. The vehicle was driven to the dealer where it was diagnosed and determined that the brakes needed to be replaced. The vehicle was not repaired. The VIN was not included in NHTSA Campaign Number: 19V904000 (SERVICE BRAKES, HYDRAULIC). The manufacturer was not notified of the failure. The failure mileage was approximately 162,000.
NHTSA ODI #11621739
200,000 miles · Oct 21, 2024
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving 7-10 MPH and depressing the brake pedal, the brake pedal felt stiff. The contact stated that while depressing the brake pedal harder, the vehicle hesitated to respond, causing the braking distance to be extended. The ABS warming light and several other …
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving 7-10 MPH and depressing the brake pedal, the brake pedal felt stiff. The contact stated that while depressing the brake pedal harder, the vehicle hesitated to respond, causing the braking distance to be extended. The ABS warming light and several other unknown warning lights were illuminated. The contact resumed driving; however, the failure worsened, and the vehicle failed to stop. The contact engaged the electric parking brake, and the vehicle stopped. The vehicle was towed to the dealer, where it was diagnosed that the ABS module, Part Number: BE5Z2C219H, had failed and needed to be replaced; however, the dealer informed the contact that the part had been discontinued. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the part had been discontinued and the VIN was not included in a recall. The failure mileage was approximately 200,000.
NHTSA ODI #11620955
130,000 miles · Aug 13, 2024
Parking BrakeService Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving 25 MPH, the brakes became inoperable. The contact stated that additional pressure was needed to depress the brake pedal while slowing down and stopping. The parking brake and ABS warning lights were illuminated. The contact stated that the failure was r…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while driving 25 MPH, the brakes became inoperable. The contact stated that additional pressure was needed to depress the brake pedal while slowing down and stopping. The parking brake and ABS warning lights were illuminated. The contact stated that the failure was related to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic). The vehicle was towed to the local dealer, where it was diagnosed and determined that the failure was due to the ABS. The vehicle was not repaired. The vehicle was taken to an independent mechanic, who determined that the failure was due to the ABS. The manufacturer was contacted and opened a case. The failure mileage was approximately 130,000.
NHTSA ODI #11608291
120,000 miles · May 28, 2024
Service Brakes, Hydraulic
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while slowing for a traffic signal at approximately 20 MPH, the ABS and several other brake warning lights illuminated. The contact depressed the brake pedal however, the vehicle was not slowing down as needed. The contact stated that the brake pedal was depressed do…
Read full complaint
The contact owns a 2010 Ford Fusion Hybrid. The contact stated while slowing for a traffic signal at approximately 20 MPH, the ABS and several other brake warning lights illuminated. The contact depressed the brake pedal however, the vehicle was not slowing down as needed. The contact stated that the brake pedal was depressed down to the floorboard. The contact stopped the vehicle by engaging the parking brake. The contact had the vehicle towed to a non-manufacturer dealer who diagnosed the vehicle and determined that the ABS Hydraulic Control Unit needed to be replaced. The vehicle was not repaired. The manufacturer was informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 19V904000 (Service Brakes Hydraulic) however, the VIN was not included. The failure mileage was approximately 120,000.
NHTSA ODI #11591095
NHTSA investigations
6DP26004 · Anti-lock Brake System (abs) Malfunction Indicator Lamp (mil) Illuminated
Opened Apr 9, 2026 · No close date supplied
Status: open (inferred from source dates) · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
The Office of Defects Investigation (ODI) received a petition on December 22, 2025, requesting a defect investigation into the hydraulic control unit (HCU) for the Anti-lock Braking System (ABS) on the MY 2010 Ford Fusion Hybrid. The petition alleges that an illuminated ABS MIL is associated with a failure of the ABS HCU, resulting in ABS malfunction, loss of traction and electronic stability control functions, and reduced braking performance, particularly on slippery road surfaces. A defect petition has been opened to evaluate the issue and determine whether to grant or deny the petition.The petition can be reviewed at NHTSA.gov under ODI number 11647929.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
EA17004 · Power Steering Failure
Opened Nov 20, 2017 · Closed Feb 9, 2024
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:rack And Pinion; Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (4)
Steering:electric Power Assist System
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE16011 · Power Steering Failure
Opened Sep 28, 2016 · Closed Dec 25, 2017
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Additional source detail variants (2)
Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Steering
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Illustration