← New search

2011 Ford F-350

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2011 Ford F-350 do not stand out strongly from the model-year median of 93.

About this comparison →

When problems were reported

Mileage at the reported incident

112 reports with mileage · 24 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Steering. Review the 50 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 21 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

4 crash reports3 fire reports3 injury reports

Equipment complaints

1 reports
Clear category filter
Mileage unknown · Mar 31, 2023
Equipment

Annual inspection of the Progress Manufacturing Equal-I-Zer (model number 90-02-1200) steel head assembly revealed cracks in the welds holding the two steel plates that support the spring bar sockets and the welds that attach the head component (part with the hitch ball) to the U-shaped bracket that attaches/bolts the head to th…

Read full complaint

Annual inspection of the Progress Manufacturing Equal-I-Zer (model number 90-02-1200) steel head assembly revealed cracks in the welds holding the two steel plates that support the spring bar sockets and the welds that attach the head component (part with the hitch ball) to the U-shaped bracket that attaches/bolts the head to the shank that is inserted into the receiver. I have pictures of the cracked welds. The assembly has been sent to a certified welding/fabrication shop for repair at my expense. If the welds failed, two scenarios are very likely: 1. The spring bars will separate from the head assembly, releasing two 20+ pound steel rods in an uncontrolled and unconstrained manner onto the pavement. Of the tow vehicle, trailer, or another car are struck by one or both rods, the result could be severe damage and/or injury. 2. If the welds holding the head assembly containing the hitch ball to the U-shaped bracket that is bolted to the shank failed, the entire hitch assembly and trailer would detach from the tow vehicle; the safety chains would provide the only mechanism to keep the trailer from detaching completely from the tow vehicle. Severe damage could occur to the trailer and tow vehicle. If the safety chains fail, the trailer would careen uncontrolled into other drivers on the road. A master welder and certified weld inspector looked at the pictures of the cracked welds and stated that "Lack of weld metal fusion, likely it was there when you bought it." I posted the pictures of my cracked welds on three FaceBook groups focused on RVing with approximately 300,000 members. Several members stated they, too, found cracks in their welds. The manufacturer was sent the pictures. They refused to stand behind their product and told me to buy a replacement head for $275.00. There were no warning lamps, messages or other symptoms of the problem prior to the failure. There may be a systemic welding problem at the PM factory.

NHTSA ODI #11514782

Official recalls

4

14V498000 · Equipment

Aug 13, 2014

PJ's Truck Bodies & Equipment Co., (PJ's) is recalling certain 2009-2013 Ford F-350, F-450, and F-550 Super Duty chassis modified by PJ's and equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.

Consequence & remedy

Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.

Remedy: PJ's has notified owners and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began on August 28, 2014. Owners may contact PJ's customer service at 1-866-475-8782.

13V535000 · Engine

Oct 30, 2013

Ford Motor Company (Ford) is recalling certain model year 2011-2012 F-350/450/550 Ambulance Package vehicles manufactured February 22, 2010, through October 19, 2012 and equipped with a 6.7L diesel engine. Due to an exhaust sensor problem, the vehicles may experience loss of power followed by an engine stall.

Consequence & remedy

Consequence: An unexpected engine stall increases the risk of a crash. Additionally, if this were to occur when the ambulance is transporting a patient, there is an increased risk of injury to the patient.

Remedy: Ford will notify owners, and dealers will replace the exhaust gas temperature sensor, free of charge. The recall began on November 25, 2013. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332. Ford's recall campaign number is 13S10.

11V128000 · Electrical System:software

Feb 24, 2011

FORD IS RECALLING CERTAIN MODEL YEAR 2011 FORD F-150, F-250, F-350, F-450, F-550, EDGE, AND LINCOLN MKX TRUCKS MANUFACTURED FROM OCTOBER 25, 2010, THROUGH NOVEMBER 20, 2010. THESE VEHICLES WERE INSPECTED USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) THAT HAD A CUSTOM SOFTWARE ROUTINE TO READ THE SUSPECT BODY CONTROL MODULE (BCM) SERIAL NUMBER. BASED ON THE SERIAL NUMBER THE BCM WAS EITHER NOT AFFECTED OR REPLACED. THE CUSTOM SOFTWARE ROUTINE WAS NOT READING THE CORRECT SET OF CHARACTERS, AND WAS NOT ABLE TO IDENTIFY A BCM THAT REQUIRED REPLACEMENT AFFECTED BCMS MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.

Consequence & remedy

Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH COULD RESULT IN A VEHICLE FIRE.

Remedy: DEALER WILL INSPECT THE BODY CONTROL MODULE AND IF NECESSARY REPLACE IT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 7, 2011. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.

10V659000 · Structure:body

Dec 29, 2010

FORD IS RECALLING CERTAIN MODEL YEAR 2011 F-150, F-250, F-350, F-450, F-550, EDGE AND LINCOLN MKX VEHICLES. DURING A SIX-DAY PRODUCTION PERIOD, THE SUPPLIER OF THE BODY CONTROL MODULE MANUFACTURED MODULES THAT MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.

Consequence & remedy

Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH CAN RESULT IN AN UNATTENDED VEHICLE FIRE.

Remedy: DEALER WILL REPLACE THE BODY CONTROL MODULE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT FORD AT 1-866-436-7332.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

RQ14005 · Vehicle Commanded Engine Shutdown

Opened Jan 13, 2015 · Closed Mar 15, 2016

Status: closed (inferred from source dates) · Electrical System:software; Engine; Engine And Engine Cooling:engine:diesel; Engine And Engine Cooling:exhaust System; Engine And Engine Cooling:exhaust System:emission Control

The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.

Additional source detail variants (5)

Electrical System:software

The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.

Engine And Engine Cooling:engine:diesel

The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.

Engine And Engine Cooling:exhaust System:emission Control

The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.

Engine And Engine Cooling:exhaust System

The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.

Engine

The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.