The contact owns a 2015 Ford F-250. The contact received notification of NHTSA Campaign Number: 25V572000 (Back Over Prevention). The contact stated that while reversing, the rearview camera displayed a blank or distorted image. The vehicle was taken to the dealer, who inspected it and determined that the vehicle did not meet th…
Read full complaint
The contact owns a 2015 Ford F-250. The contact received notification of NHTSA Campaign Number: 25V572000 (Back Over Prevention). The contact stated that while reversing, the rearview camera displayed a blank or distorted image. The vehicle was taken to the dealer, who inspected it and determined that the vehicle did not meet the requirement to replace the rearview camera. The vehicle was not repaired. The manufacturer was made aware of the failure, and a case was filed. The failure mileage was approximately 98,000.
NHTSA ODI #11746533
140,000 miles · Mar 17, 2026
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact stated that while reversing the back over prevention camera malfunctioned and displayed a black or distorted screen, creating a rear visibility hazard for the driver. The contact indicated that the failure was present after the vehicle had been repaired under NHTSA Campaign Number:…
Read full complaint
The contact owns a 2015 Ford F-250. The contact stated that while reversing the back over prevention camera malfunctioned and displayed a black or distorted screen, creating a rear visibility hazard for the driver. The contact indicated that the failure was present after the vehicle had been repaired under NHTSA Campaign Number: 19V401000 (EQUIPMENT). The cause of the failure was not yet determined. The manufacturer and local dealer were notified of the failure, but no assistance was provided. The failure mileage was 140,000.
NHTSA ODI #11724967
150,000 miles · Dec 23, 2025
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 25V270000 (Back Over Prevention); however, the failure occurred. The contact stated that the rearview camera displayed a black screen while the vehicle was in reverse. The message "Rearview Camera not Available" was …
Read full complaint
The contact owns a 2015 Ford F-250. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 25V270000 (Back Over Prevention); however, the failure occurred. The contact stated that the rearview camera displayed a black screen while the vehicle was in reverse. The message "Rearview Camera not Available" was displayed. The contact stated that the failure obstructed the road's visibility, which prevented the driver from safely operating the vehicle. The vehicle was taken to the dealer, and the contact was informed that a diagnostic test was needed to determine the cause of the failure. The vehicle was not diagnosed or repaired due to the cost. The manufacturer was not notified of the failure. The failure mileage was approximately 150,000.
NHTSA ODI #11706806
104,327 miles · Sep 10, 2025
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact stated that while attempting to reverse, the rearview camera became inoperable. The contact stated that the rearview camera image appeared blank and occasionally distorted. The contact received notification of NHTSA Campaign Number: 25V270000 (Back Over Prevention); however, the pa…
Read full complaint
The contact owns a 2015 Ford F-250. The contact stated that while attempting to reverse, the rearview camera became inoperable. The contact stated that the rearview camera image appeared blank and occasionally distorted. The contact received notification of NHTSA Campaign Number: 25V270000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The dealer was contacted. The dealer confirmed that parts were not yet available. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 104,327.
NHTSA ODI #11686277
Mileage unknown · Aug 12, 2025
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact received notification of NHTSA Campaign Number: 25V270000 (BACK OVER PREVENTION); however, the part to do the recall repair was not yet available. The rearview camera displayed a black screen while the vehicle was in reverse(R). The failure prevented the contact from safely operati…
Read full complaint
The contact owns a 2015 Ford F-250. The contact received notification of NHTSA Campaign Number: 25V270000 (BACK OVER PREVENTION); however, the part to do the recall repair was not yet available. The rearview camera displayed a black screen while the vehicle was in reverse(R). The failure prevented the contact from safely operating the vehicle. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown.
NHTSA ODI #11680079
120,000 miles · Jul 28, 2025
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact stated that while shifted into reverse(R), the back over prevention screen failed to properly display an image of the rear of the vehicle. No warning light was illuminated. The message to “See Dealer" was displayed. The local dealer was contacted, but the vehicle was not diagnosed …
Read full complaint
The contact owns a 2015 Ford F-250. The contact stated that while shifted into reverse(R), the back over prevention screen failed to properly display an image of the rear of the vehicle. No warning light was illuminated. The message to “See Dealer" was displayed. The local dealer was contacted, but the vehicle was not diagnosed or repaired. In addition, the contact related the failure to an unknown recall; however, the VIN was not included. The manufacturer was made aware of the failure. The failure mileage was approximately 120,000.
NHTSA ODI #11676559
68,720 miles · Jun 18, 2025
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact stated that upon attempting to reverse, the back over prevention camera display failed to function. The message "Camera not Available - Please Contact dealer" was displayed. The contact stated there were no warning lights illuminated. The local dealer was contacted; however, the ve…
Read full complaint
The contact owns a 2015 Ford F-250. The contact stated that upon attempting to reverse, the back over prevention camera display failed to function. The message "Camera not Available - Please Contact dealer" was displayed. The contact stated there were no warning lights illuminated. The local dealer was contacted; however, the vehicle was not diagnosed or repaired. The contact was informed that the VIN was not under recall. The manufacturer was notified of the failure. The approximate failure mileage was 68,720.
NHTSA ODI #11667700
Mileage unknown · May 28, 2025
Back Over Prevention
Backup camera is only displaying blue screen when in reverse. Symptoms consistent with other 2015 F250s currently under recall, yet my vin is not included for some reason. Issue was reported to Ford, but they refused to checkout the problem or fix it.
NHTSA ODI #11663400
96,000 miles · May 15, 2025
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact stated that while reversing, the rearview camera image was black or distorted. There was no warning light illuminated. The dealer was notified of the failure and informed the contact that the VIN was not included in NHTSA Campaign Number: 25V270000 (Back Over Prevention). The deale…
Read full complaint
The contact owns a 2015 Ford F-250. The contact stated that while reversing, the rearview camera image was black or distorted. There was no warning light illuminated. The dealer was notified of the failure and informed the contact that the VIN was not included in NHTSA Campaign Number: 25V270000 (Back Over Prevention). The dealer informed the contact that the rearview camera needed to be replaced; however, the vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 96,000.
NHTSA ODI #11661248
Mileage unknown · May 13, 2025
Back Over Prevention
The contact owns a 2015 Ford F-250. The contact received notification of NHTSA Campaign Number: 25V270000 (Back Over Prevention) and would like to be removed from the recall distribution list. The local dealer and manufacturer were not contacted.
Ford Motor Company (Ford) is recalling certain 2015-2019 Lincoln MKC, Mustang, F-350 SD, F-250 SD, F-450 SD, 2015-2017 Lincoln Navigator, Expedition, 2015-2018 Edge, Transit Connect, 2016-2019 F-550 SD, Transit, 2017-2019 Econoline, and 2019 Ranger vehicles. The rearview camera may display a distorted, inverted, or blank image when the vehicle is in reverse.
Consequence & remedy
Consequence: A rearview camera that displays an inverted, distorted, or blank image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the rearview camera as necessary, free of charge. Owner notification letters were mailed January 13, 2026. Ford owners will receive letters in phases, beginning January 2026 and June 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S89. This recall expands previous NHTSA recall number 25V270. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning September 8, 2025.
Ford Motor Company (Ford) is recalling certain model year 2015 F-250, F-350, F-450, and F-550 Super Duty trucks manufactured September 13, 2013, through March 28, 2014, and equipped with 6.2L gasoline or 6.7L diesel engines and 6R140 transmissions. An error with the transmission control software may be such that while shifting from "Park" to "Drive" the vehicle may display "Drive" but possibly engage "Reverse" for 1.5 seconds before engaging "Drive." Therefore, the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) number 102, "Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect."
Consequence & remedy
Consequence: If the vehicle is in "Reverse" while the while the gear selection shows "Drive," unexpected movement could occur, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the transmission software, free of charge. The recall began on May 6, 2014. Owners may contact Fords customer service at 1-800-392-3673. Ford's number for this recall is 14C04.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
Status: open (inferred from source dates) · Fuel System, Diesel; Fuel System, Other:fuel Filter
The Office of Defect Investigations (ODI) has received 27 complaints alleging diesel fuel leaks due to a fracture in the secondary fuel filter housing in model year (MY) 2015-2021 Ford Motor Company (Ford) F-250, 350, 450, and 550 Super Duty vehicles equipped with 6.7L diesel engines. Of these complaints, 12 describe an engine compartment fire. The proximity of the secondary fuel filter to high heat sources creates a potential for autoignition thermal events and fires. ODI has contacted the vehicle manufacturer, Ford, and the filter manufacturer, Allevard Sogefi USA (Sogefi), and learned that the low-pressure fuel system is capable of a maximum operating pressure of 8.5 Bar, while the secondary fuel filter is only tested to seven (7) Bar during the manufacturing process. Additionally, changes starting in 2022 by both Ford and Sogefi align with a lack of similar complaints on MY 2022 and newer vehicles. ODI is opening this Preliminary Evaluation (PE) to evaluate the severity of the potential problem and to fully assess the potential safety-related problems. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Fuel System, Diesel
The Office of Defect Investigations (ODI) has received 27 complaints alleging diesel fuel leaks due to a fracture in the secondary fuel filter housing in model year (MY) 2015-2021 Ford Motor Company (Ford) F-250, 350, 450, and 550 Super Duty vehicles equipped with 6.7L diesel engines. Of these complaints, 12 describe an engine compartment fire. The proximity of the secondary fuel filter to high heat sources creates a potential for autoignition thermal events and fires. ODI has contacted the vehicle manufacturer, Ford, and the filter manufacturer, Allevard Sogefi USA (Sogefi), and learned that the low-pressure fuel system is capable of a maximum operating pressure of 8.5 Bar, while the secondary fuel filter is only tested to seven (7) Bar during the manufacturing process. Additionally, changes starting in 2022 by both Ford and Sogefi align with a lack of similar complaints on MY 2022 and newer vehicles. ODI is opening this Preliminary Evaluation (PE) to evaluate the severity of the potential problem and to fully assess the potential safety-related problems. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Fuel System, Other:fuel Filter
The Office of Defect Investigations (ODI) has received 27 complaints alleging diesel fuel leaks due to a fracture in the secondary fuel filter housing in model year (MY) 2015-2021 Ford Motor Company (Ford) F-250, 350, 450, and 550 Super Duty vehicles equipped with 6.7L diesel engines. Of these complaints, 12 describe an engine compartment fire. The proximity of the secondary fuel filter to high heat sources creates a potential for autoignition thermal events and fires. ODI has contacted the vehicle manufacturer, Ford, and the filter manufacturer, Allevard Sogefi USA (Sogefi), and learned that the low-pressure fuel system is capable of a maximum operating pressure of 8.5 Bar, while the secondary fuel filter is only tested to seven (7) Bar during the manufacturing process. Additionally, changes starting in 2022 by both Ford and Sogefi align with a lack of similar complaints on MY 2022 and newer vehicles. ODI is opening this Preliminary Evaluation (PE) to evaluate the severity of the potential problem and to fully assess the potential safety-related problems. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ14005 · Vehicle Commanded Engine Shutdown
Opened Jan 13, 2015 · Closed Mar 15, 2016
Status: closed (inferred from source dates) · Electrical System:software; Engine; Engine And Engine Cooling:engine:diesel; Engine And Engine Cooling:exhaust System; Engine And Engine Cooling:exhaust System:emission Control
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Additional source detail variants (5)
Electrical System:software
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine And Engine Cooling:engine:diesel
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine And Engine Cooling:exhaust System:emission Control
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine And Engine Cooling:exhaust System
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
2015 Ford F-250 Sd Problems, Complaints & Recalls | Skip That Year
Illustration