IllustrationDriver side brake hose failure at upper crimp on the hose caused loss of brake fluid and spongy peddle
2013 Ford F-150
Owner reports · Recalls · Investigations
More warning signs than most F-150 years
Owner complaints for the 2013 Ford F-150 are substantially higher than the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
3300–25K
32125–50K
46250–75K
39775–100K
454100–150K
251150K+
2,215 reports with mileage · 765 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 1,335 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 547 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 322 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
77 crash reports35 fire reports53 injury reports
What owners actually said
2,980 reportsKnown issues with design and life expectancy of the exhaust manifolds and bolts thousands of owners are replacing manifolds due to warping and shearing of bolts when exhaust overheats. I’m currently getting quotes to replace due to failure on a gently used truck. Failure happened during a highway trip of a couple hundred miles…
Read full complaint
Known issues with design and life expectancy of the exhaust manifolds and bolts thousands of owners are replacing manifolds due to warping and shearing of bolts when exhaust overheats. I’m currently getting quotes to replace due to failure on a gently used truck. Failure happened during a highway trip of a couple hundred miles under no additional load.
I have a 2013 Ford 150 King Ranch 4X4 with the 6R80 transmission and approximately 125k miles on it. This morning, I was stopped at a red light and upon accelerating my truck would not shift out of first gear. The speedometer stopped working, and engine light came on. I pulled over and turned off the truck to inspect it. I res…
Read full complaint
I have a 2013 Ford 150 King Ranch 4X4 with the 6R80 transmission and approximately 125k miles on it. This morning, I was stopped at a red light and upon accelerating my truck would not shift out of first gear. The speedometer stopped working, and engine light came on. I pulled over and turned off the truck to inspect it. I restarted the truck and it was shifting appropriately for about 5 miles when it all of a sudden shifted into first gear while I was driving approximately 35-40mph, nearly causing an accident until I could safely pull over. I researched symptoms and found information regarding the molded lead frame on the 2013 model f150s. I understand Ford warranty coverage was limited to 10 years, but I believe Ford should continue to honor this known defect in there vehicle. This is a serious safety concern. If it would have been raining, or icy weather, it could have caused a serious accident and/or death to myself or others. Ford is aware of these issues, and yet owners are still responsible for their defective parts after warranty expires. I believe the manufacturer has an obligation to address this known problem. I am requesting Ford review my vehicle and this failure as a safety-related defect and provide assistance with the repair, as well as covering the cost of repair in full. At minimum, I am requesting Ford provide reimbursement based on the known history of the component and the potential safety consequences of its failure.
I have experienced several downshifts at high speed to low gear while driving. This defect can cause sudden downshifts at highway speeds, creating a serious risk of loss of control, skidding, or collision. The vehicle experiences sudden downshifts, wrench‑light warnings, and loss of power, which matches the defect described in r…
Read full complaint
I have experienced several downshifts at high speed to low gear while driving. This defect can cause sudden downshifts at highway speeds, creating a serious risk of loss of control, skidding, or collision. The vehicle experiences sudden downshifts, wrench‑light warnings, and loss of power, which matches the defect described in recall 19S07. I contacted both a local dealer and the regional Ford representatives, Ford marked the recall as completed, but the repair was either not performed or performed without resolution and the defect symptoms continue.
In 2019, vehicle had a recall for output speed sensor in the transmission. Initial Ford dealership in Indiana (Don Hinds), reprogrammed. They did not test drive vehicle or follow additional instruction to replace the molded leadframe. Vehicle has continued to demonstrate OSS sensor failure. Every time we drive it, the vehicle do…
Read full complaint
In 2019, vehicle had a recall for output speed sensor in the transmission. Initial Ford dealership in Indiana (Don Hinds), reprogrammed. They did not test drive vehicle or follow additional instruction to replace the molded leadframe. Vehicle has continued to demonstrate OSS sensor failure. Every time we drive it, the vehicle downshifts from 6th gear to 1st gear with malfunction indicator light and wrench light coming on. Spoke with Don Hinds Ford and they agree this needs to be covered by Ford. They contacted ford Recall number repeatedly. I contacted them repeatedly starting in April. I was told to take my vehicle to a Ford dealership in Arizona (where I currently live) - Sanderson Ford. They ran the codes and agreed the molded leadframe needs to be replaced. They and I have contacted Ford Customer Assistance Center multiple times. Initially, they stated only one call to them, but the individual, Lisa, hung up on me and closed the file. I have been calling every week since May 12th and have never been told the case was closed until August 19th when I was told case was closed and they would open a new case. They have not communicated with Sanderson Ford or myself since that time. The vehicle is unsafe to drive, it is my mode of transportation and is currently sitting at Sanderson Ford. Ford corporate is not responding to any communciation from myself or the dealership. The truck issue is putting myself and other drivers at risk because the vehicle cannot be controlled when the OSS sensor fails. Initial case file: [XXX] Updated case file: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I was driving on interstate approximatly 70 mph when it downshifted into second gear and and almost got rearended by a semi truck that was following behind my truck and luckily was able to swerve to miss hitting us. I Believe it is the 6r80 transmission conductor plate that is the cause of the issue
Lead Frame failure. 19N01 recall. When the failure occurred I was on I-80 driving at 78 mph. The vehicle suddenly down shifted causing my speed to drop to a dangerous speed. I had to exit the roadway immediately to avoid being rear ended or worse. I never received a recall letter from Ford.
The contact owns a 2013 Ford F-150. The contact stated that while driving approximately 35 MPH, the brake light warning light illuminated, and while depressing brake pedal, the brake pedal went to the floorboard. The transmission was shifted to a lower gear, and the hazard lights were activated, and the vehicle was slowly driven…
Read full complaint
The contact owns a 2013 Ford F-150. The contact stated that while driving approximately 35 MPH, the brake light warning light illuminated, and while depressing brake pedal, the brake pedal went to the floorboard. The transmission was shifted to a lower gear, and the hazard lights were activated, and the vehicle was slowly driven to the residence. The vehicle was later towed to a dealer to be diagnosed, and it was determined that the brake booster was contaminated with brake fluid, and that the brake master cylinder piston had a tear in the piston seal, and the brake master cylinder and brake booster needed to be replaced. The vehicle was repaired. The contact associated the failure with Manufacturer Recall Number: 16F24. The manufacturer was notified of the failure and a complaint was filed. The failure mileage was 32,145.
Despite NHTSA and Ford stating the "recall" has been fixed on my 2013 Ford F150, my truck still performs the exact symptoms of a Transmission molded leadframe failure. Not only my safety, but the safety of others was put as risk when my truck suddenly downshifted into what appeared to first gear, while traveling on the road, wit…
Read full complaint
Despite NHTSA and Ford stating the "recall" has been fixed on my 2013 Ford F150, my truck still performs the exact symptoms of a Transmission molded leadframe failure. Not only my safety, but the safety of others was put as risk when my truck suddenly downshifted into what appeared to first gear, while traveling on the road, with no indication. I lost power and was no longer able to move at the speed of traffic. Had this happened at highway speed I would have almost certainly lost traction and could have crashed. I was sitll forced to take evasive action and move to the side of the road, where my truck would not shift out of first gear until after a full restart. No warning lights, lamps, or other messages were displayed before or after the incident.
The contact owns a 2013 Ford F-150. The contact stated that while driving 70 MPH, the transmission unexpectedly downshifted and remained stuck in first gear. The contact was able to drive to a residence. The vehicle was taken to a dealer, where a transmission recall associated with the failure was completed. Additionally, the co…
Read full complaint
The contact owns a 2013 Ford F-150. The contact stated that while driving 70 MPH, the transmission unexpectedly downshifted and remained stuck in first gear. The contact was able to drive to a residence. The vehicle was taken to a dealer, where a transmission recall associated with the failure was completed. Additionally, the contact was informed that the leadframe needed to be replaced; however, the repair was not covered under Customer Satisfaction Program Number: 19N01 (Transmission Molded Leadframe Extended Coverage) because the coverage had expired a week prior to the failure. The contact stated that the vehicle later remained stuck in first gear and failed to exceed 20 MPH, with the powertrain warning light illuminated. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 160,000.
Official recalls
319V433000 · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Jun 10, 2019
Ford Motor Company (Ford) is recalling certain 2013 F-150 vehicles equipped with 5.0L or 6.2L gasoline engines, that previously had the powertrain control module (PCM) software reprogrammed under recall 19V-075. The software used to reprogram the PCM did not have the necessary updates to prevent the transmission from unexpectedly downshifting into first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began June 24, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S19.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Ford Motor Company (Ford) is recalling certain 2013 F-150 vehicles equipped with 5.0L or 6.2L gasoline engines, that previously had the powertrain control module (PCM) software reprogrammed under recall 19V-075. The software used to reprogram the PCM did not have the necessary updates to prevent the transmission from unexpectedly downshifting into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began June 24, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S19.
Power Train:automatic Transmission
Ford Motor Company (Ford) is recalling certain 2013 F-150 vehicles equipped with 5.0L or 6.2L gasoline engines, that previously had the powertrain control module (PCM) software reprogrammed under recall 19V-075. The software used to reprogram the PCM did not have the necessary updates to prevent the transmission from unexpectedly downshifting into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began June 24, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S19.
19V075000 · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Feb 11, 2019
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Power Train:automatic Transmission
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
16V345000 · Service Brakes, Hydraulic:fluid
May 24, 2016
Ford Motor Company (Ford) is recalling certain model year 2013-2014 F-150 vehicles manufactured August 1, 2013, to August 31, 2014 equipped with 3.5L engines. The master cylinder rear cup seal may roll, resulting in brake fluid leakage from the primary reservoir into the brake booster.
Consequence & remedy
Consequence: Loss of brake fluid from the primary reservoir results in a complete loss of front brake function, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the brake master cylinder and, if necessary, the brake booster, free of charge. The recall began on October 28, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S24.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3RQ17010 · Unexpected Transmission Downshift
Opened Dec 25, 2017 · Closed Oct 22, 2019
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
PE16003 · Master Cylinder External Leak
Opened Feb 29, 2016 · Closed Jul 26, 2016
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:fluid; Service Brakes, Hydraulic:foundation Components:master Cylinder
On May 23, 2016, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA regarding a master cylinder defect that could result in loss of the front brake circuit in approximately 225,012 model year 2013 through 2014 Ford F-150 vehicles equipped with 3.5-liter GTDI engines and built at the Dearborn Truck Plant from August 1, 2013 through August 22, 2014; and the Kansas City Assembly Plant from August 1, 2013 through August 31, 2014 (NHTSA Recall #16V-345, Ford Recall #16S24).Ford indicated that the rearmost cup seal in the brake master cylinder may roll, resulting in leakage from the brake fluid reservoir to the brake booster.According to Ford's DIR, Depending on the amount of brake fluid loss from the brake master cylinder into the brake booster, the driver will experience an audible chime, message center alert, red brake warning light in the instrument cluster and may begin to experience a change in brake pedal travel and feel.In the event that a loss of brake fluid is substantial enough to reduce brake function to the front wheels, the driver may experience longer pedal travel, increased pedal effort, and extended stopping distance, increasing the risk of a crash.Full braking function would remain in the rear wheel brake circuit.Ford's recall will replace the master cylinder and, if the master cylinder is leaking, also replace the brake booster.Seventy-three (73) of the complaints received by ODI contained vehicle identification number (VIN) information required to determine date of build and recall applicability.ODI's analysis found that 66 complaints to ODI and 278 complaints to Ford involving vehicles built in the range covered by 16V-345, resulting in an overall complaint rate of 152.9 incidents per 100,000 vehicles.Twelve (12) crash incidents were reported, including 11 with VIN information.All 11 crash incidents with VIN information reported involve vehicles covered by Ford's recall.ODI's analysis identified 7 ODI complaints and 36 Ford complaints in the 194,139 subject vehicles built outside of the build range for 16V-345, resulting in a complaint rate of 22.1 incidents per 100,000 vehicles.Ford indicated that warranty return analyses identified issues with minor internal leakage between circuits due to internal contamination caused by supplier assembly plant cleanliness concerns in these vehicles.Ford assessed the internal leak condition as an early-life condition with minimal safety risk that does not result in loss of fluid or circuit failure.ODI will continue to monitor complaints in subject vehicles not included in 16V-345.No complaints have been identified in MY 2013 through 2014 Ford F-150 vehicles equipped with other engine options.The recall action initiated by the manufacturer appears to address the safety risks identified by this investigation.This preliminary evaluation is closed.The ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchSafetylssues under the following identification numbers:10870768, 10870747, 10870511, 10870395, 10870055, 10869981, 10865843, 10865521, 10865342, 10865043, 10864862, 10864714, 10864360, 10863982, 10863527, 10862333, 10862047, 10861735, 10861190, 10860378, 10860118, 10855381, 10855356, 10854785, 10853751, 10853295, 10853012, 10852349, 10852134, 10852037, 10851317, 10851268, 10851109, 10850015, 10849862, 10846488, 10846335, 10846193, 10846006, 10840414, 10840377, 10839994, 10839985, 10839981, 10839833, 10839825, 10839816, 10838782, 10838510, 10818273, 10817706, 10809601, 10788886, 10788369, 10785526, 10779854, 10776834, 10766291, 10762034, 10761412, 10760663, 10758997, 10750065, 10749886, 107
Additional source detail variants (4)
Service Brakes
On May 23, 2016, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA regarding a master cylinder defect that could result in loss of the front brake circuit in approximately 225,012 model year 2013 through 2014 Ford F-150 vehicles equipped with 3.5-liter GTDI engines and built at the Dearborn Truck Plant from August 1, 2013 through August 22, 2014; and the Kansas City Assembly Plant from August 1, 2013 through August 31, 2014 (NHTSA Recall #16V-345, Ford Recall #16S24).Ford indicated that the rearmost cup seal in the brake master cylinder may roll, resulting in leakage from the brake fluid reservoir to the brake booster.According to Ford's DIR, Depending on the amount of brake fluid loss from the brake master cylinder into the brake booster, the driver will experience an audible chime, message center alert, red brake warning light in the instrument cluster and may begin to experience a change in brake pedal travel and feel.In the event that a loss of brake fluid is substantial enough to reduce brake function to the front wheels, the driver may experience longer pedal travel, increased pedal effort, and extended stopping distance, increasing the risk of a crash.Full braking function would remain in the rear wheel brake circuit.Ford's recall will replace the master cylinder and, if the master cylinder is leaking, also replace the brake booster.Seventy-three (73) of the complaints received by ODI contained vehicle identification number (VIN) information required to determine date of build and recall applicability.ODI's analysis found that 66 complaints to ODI and 278 complaints to Ford involving vehicles built in the range covered by 16V-345, resulting in an overall complaint rate of 152.9 incidents per 100,000 vehicles.Twelve (12) crash incidents were reported, including 11 with VIN information.All 11 crash incidents with VIN information reported involve vehicles covered by Ford's recall.ODI's analysis identified 7 ODI complaints and 36 Ford complaints in the 194,139 subject vehicles built outside of the build range for 16V-345, resulting in a complaint rate of 22.1 incidents per 100,000 vehicles.Ford indicated that warranty return analyses identified issues with minor internal leakage between circuits due to internal contamination caused by supplier assembly plant cleanliness concerns in these vehicles.Ford assessed the internal leak condition as an early-life condition with minimal safety risk that does not result in loss of fluid or circuit failure.ODI will continue to monitor complaints in subject vehicles not included in 16V-345.No complaints have been identified in MY 2013 through 2014 Ford F-150 vehicles equipped with other engine options.The recall action initiated by the manufacturer appears to address the safety risks identified by this investigation.This preliminary evaluation is closed.The ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchSafetylssues under the following identification numbers:10870768, 10870747, 10870511, 10870395, 10870055, 10869981, 10865843, 10865521, 10865342, 10865043, 10864862, 10864714, 10864360, 10863982, 10863527, 10862333, 10862047, 10861735, 10861190, 10860378, 10860118, 10855381, 10855356, 10854785, 10853751, 10853295, 10853012, 10852349, 10852134, 10852037, 10851317, 10851268, 10851109, 10850015, 10849862, 10846488, 10846335, 10846193, 10846006, 10840414, 10840377, 10839994, 10839985, 10839981, 10839833, 10839825, 10839816, 10838782, 10838510, 10818273, 10817706, 10809601, 10788886, 10788369, 10785526, 10779854, 10776834, 10766291, 10762034, 10761412, 10760663, 10758997, 10750065, 10749886, 107
Service Brakes, Hydraulic:fluid
On May 23, 2016, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA regarding a master cylinder defect that could result in loss of the front brake circuit in approximately 225,012 model year 2013 through 2014 Ford F-150 vehicles equipped with 3.5-liter GTDI engines and built at the Dearborn Truck Plant from August 1, 2013 through August 22, 2014; and the Kansas City Assembly Plant from August 1, 2013 through August 31, 2014 (NHTSA Recall #16V-345, Ford Recall #16S24).Ford indicated that the rearmost cup seal in the brake master cylinder may roll, resulting in leakage from the brake fluid reservoir to the brake booster.According to Ford's DIR, Depending on the amount of brake fluid loss from the brake master cylinder into the brake booster, the driver will experience an audible chime, message center alert, red brake warning light in the instrument cluster and may begin to experience a change in brake pedal travel and feel.In the event that a loss of brake fluid is substantial enough to reduce brake function to the front wheels, the driver may experience longer pedal travel, increased pedal effort, and extended stopping distance, increasing the risk of a crash.Full braking function would remain in the rear wheel brake circuit.Ford's recall will replace the master cylinder and, if the master cylinder is leaking, also replace the brake booster.Seventy-three (73) of the complaints received by ODI contained vehicle identification number (VIN) information required to determine date of build and recall applicability.ODI's analysis found that 66 complaints to ODI and 278 complaints to Ford involving vehicles built in the range covered by 16V-345, resulting in an overall complaint rate of 152.9 incidents per 100,000 vehicles.Twelve (12) crash incidents were reported, including 11 with VIN information.All 11 crash incidents with VIN information reported involve vehicles covered by Ford's recall.ODI's analysis identified 7 ODI complaints and 36 Ford complaints in the 194,139 subject vehicles built outside of the build range for 16V-345, resulting in a complaint rate of 22.1 incidents per 100,000 vehicles.Ford indicated that warranty return analyses identified issues with minor internal leakage between circuits due to internal contamination caused by supplier assembly plant cleanliness concerns in these vehicles.Ford assessed the internal leak condition as an early-life condition with minimal safety risk that does not result in loss of fluid or circuit failure.ODI will continue to monitor complaints in subject vehicles not included in 16V-345.No complaints have been identified in MY 2013 through 2014 Ford F-150 vehicles equipped with other engine options.The recall action initiated by the manufacturer appears to address the safety risks identified by this investigation.This preliminary evaluation is closed.The ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchSafetylssues under the following identification numbers:10870768, 10870747, 10870511, 10870395, 10870055, 10869981, 10865843, 10865521, 10865342, 10865043, 10864862, 10864714, 10864360, 10863982, 10863527, 10862333, 10862047, 10861735, 10861190, 10860378, 10860118, 10855381, 10855356, 10854785, 10853751, 10853295, 10853012, 10852349, 10852134, 10852037, 10851317, 10851268, 10851109, 10850015, 10849862, 10846488, 10846335, 10846193, 10846006, 10840414, 10840377, 10839994, 10839985, 10839981, 10839833, 10839825, 10839816, 10838782, 10838510, 10818273, 10817706, 10809601, 10788886, 10788369, 10785526, 10779854, 10776834, 10766291, 10762034, 10761412, 10760663, 10758997, 10750065, 10749886, 107
Service Brakes, Hydraulic
On May 23, 2016, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA regarding a master cylinder defect that could result in loss of the front brake circuit in approximately 225,012 model year 2013 through 2014 Ford F-150 vehicles equipped with 3.5-liter GTDI engines and built at the Dearborn Truck Plant from August 1, 2013 through August 22, 2014; and the Kansas City Assembly Plant from August 1, 2013 through August 31, 2014 (NHTSA Recall #16V-345, Ford Recall #16S24).Ford indicated that the rearmost cup seal in the brake master cylinder may roll, resulting in leakage from the brake fluid reservoir to the brake booster.According to Ford's DIR, Depending on the amount of brake fluid loss from the brake master cylinder into the brake booster, the driver will experience an audible chime, message center alert, red brake warning light in the instrument cluster and may begin to experience a change in brake pedal travel and feel.In the event that a loss of brake fluid is substantial enough to reduce brake function to the front wheels, the driver may experience longer pedal travel, increased pedal effort, and extended stopping distance, increasing the risk of a crash.Full braking function would remain in the rear wheel brake circuit.Ford's recall will replace the master cylinder and, if the master cylinder is leaking, also replace the brake booster.Seventy-three (73) of the complaints received by ODI contained vehicle identification number (VIN) information required to determine date of build and recall applicability.ODI's analysis found that 66 complaints to ODI and 278 complaints to Ford involving vehicles built in the range covered by 16V-345, resulting in an overall complaint rate of 152.9 incidents per 100,000 vehicles.Twelve (12) crash incidents were reported, including 11 with VIN information.All 11 crash incidents with VIN information reported involve vehicles covered by Ford's recall.ODI's analysis identified 7 ODI complaints and 36 Ford complaints in the 194,139 subject vehicles built outside of the build range for 16V-345, resulting in a complaint rate of 22.1 incidents per 100,000 vehicles.Ford indicated that warranty return analyses identified issues with minor internal leakage between circuits due to internal contamination caused by supplier assembly plant cleanliness concerns in these vehicles.Ford assessed the internal leak condition as an early-life condition with minimal safety risk that does not result in loss of fluid or circuit failure.ODI will continue to monitor complaints in subject vehicles not included in 16V-345.No complaints have been identified in MY 2013 through 2014 Ford F-150 vehicles equipped with other engine options.The recall action initiated by the manufacturer appears to address the safety risks identified by this investigation.This preliminary evaluation is closed.The ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchSafetylssues under the following identification numbers:10870768, 10870747, 10870511, 10870395, 10870055, 10869981, 10865843, 10865521, 10865342, 10865043, 10864862, 10864714, 10864360, 10863982, 10863527, 10862333, 10862047, 10861735, 10861190, 10860378, 10860118, 10855381, 10855356, 10854785, 10853751, 10853295, 10853012, 10852349, 10852134, 10852037, 10851317, 10851268, 10851109, 10850015, 10849862, 10846488, 10846335, 10846193, 10846006, 10840414, 10840377, 10839994, 10839985, 10839981, 10839833, 10839825, 10839816, 10838782, 10838510, 10818273, 10817706, 10809601, 10788886, 10788369, 10785526, 10779854, 10776834, 10766291, 10762034, 10761412, 10760663, 10758997, 10750065, 10749886, 107
Service Brakes, Hydraulic:foundation Components:master Cylinder
On May 23, 2016, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA regarding a master cylinder defect that could result in loss of the front brake circuit in approximately 225,012 model year 2013 through 2014 Ford F-150 vehicles equipped with 3.5-liter GTDI engines and built at the Dearborn Truck Plant from August 1, 2013 through August 22, 2014; and the Kansas City Assembly Plant from August 1, 2013 through August 31, 2014 (NHTSA Recall #16V-345, Ford Recall #16S24).Ford indicated that the rearmost cup seal in the brake master cylinder may roll, resulting in leakage from the brake fluid reservoir to the brake booster.According to Ford's DIR, Depending on the amount of brake fluid loss from the brake master cylinder into the brake booster, the driver will experience an audible chime, message center alert, red brake warning light in the instrument cluster and may begin to experience a change in brake pedal travel and feel.In the event that a loss of brake fluid is substantial enough to reduce brake function to the front wheels, the driver may experience longer pedal travel, increased pedal effort, and extended stopping distance, increasing the risk of a crash.Full braking function would remain in the rear wheel brake circuit.Ford's recall will replace the master cylinder and, if the master cylinder is leaking, also replace the brake booster.Seventy-three (73) of the complaints received by ODI contained vehicle identification number (VIN) information required to determine date of build and recall applicability.ODI's analysis found that 66 complaints to ODI and 278 complaints to Ford involving vehicles built in the range covered by 16V-345, resulting in an overall complaint rate of 152.9 incidents per 100,000 vehicles.Twelve (12) crash incidents were reported, including 11 with VIN information.All 11 crash incidents with VIN information reported involve vehicles covered by Ford's recall.ODI's analysis identified 7 ODI complaints and 36 Ford complaints in the 194,139 subject vehicles built outside of the build range for 16V-345, resulting in a complaint rate of 22.1 incidents per 100,000 vehicles.Ford indicated that warranty return analyses identified issues with minor internal leakage between circuits due to internal contamination caused by supplier assembly plant cleanliness concerns in these vehicles.Ford assessed the internal leak condition as an early-life condition with minimal safety risk that does not result in loss of fluid or circuit failure.ODI will continue to monitor complaints in subject vehicles not included in 16V-345.No complaints have been identified in MY 2013 through 2014 Ford F-150 vehicles equipped with other engine options.The recall action initiated by the manufacturer appears to address the safety risks identified by this investigation.This preliminary evaluation is closed.The ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchSafetylssues under the following identification numbers:10870768, 10870747, 10870511, 10870395, 10870055, 10869981, 10865843, 10865521, 10865342, 10865043, 10864862, 10864714, 10864360, 10863982, 10863527, 10862333, 10862047, 10861735, 10861190, 10860378, 10860118, 10855381, 10855356, 10854785, 10853751, 10853295, 10853012, 10852349, 10852134, 10852037, 10851317, 10851268, 10851109, 10850015, 10849862, 10846488, 10846335, 10846193, 10846006, 10840414, 10840377, 10839994, 10839985, 10839981, 10839833, 10839825, 10839816, 10838782, 10838510, 10818273, 10817706, 10809601, 10788886, 10788369, 10785526, 10779854, 10776834, 10766291, 10762034, 10761412, 10760663, 10758997, 10750065, 10749886, 107
PE13018 · Reduced Power During Hard Acceleration
Opened May 22, 2013 · Closed Apr 7, 2014
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Additional source detail variants (2)
Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Engine
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of