IllustrationBRAKES APPLIED TO STOP, PEDAL WENT TO FLOOR, VEHICLE INCREASED, BRAKES COULDN'T WORK HAD TO TURN KEY OF TO STOP ENGINE.
2012 Ford F-150
Owner reports · Recalls · Investigations
More warning signs than most F-150 years
Owner complaints for the 2012 Ford F-150 are substantially higher than the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
3550–25K
24225–50K
26450–75K
21775–100K
259100–150K
133150K+
1,470 reports with mileage · 310 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 678 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 482 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 204 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
40 crash reports14 fire reports23 injury reports
Engine complaints
482 reportsVEHICLE IS A FORD F150 2012 ECOBOOST V6 3.5L. VEHICLE WAS DRIVEN IN HIGH HUMIDITY AND FOG WITH CRUISE CONTROL ON FOR A TIME PERIOD OF AROUND 4 HOURS WITHOUT SPOOLING THE TURBO CHARGERS. UPON TRYING TO PASS ANOTHER VEHICLE THE GAS PEDAL WAS PRESSED TO ACCELERATE. VEHICLE BEGAN TO SHAKE VIOLENTLY, AND BEGAN TO LOSE POWER. VEHICLE …
Read full complaint
VEHICLE IS A FORD F150 2012 ECOBOOST V6 3.5L. VEHICLE WAS DRIVEN IN HIGH HUMIDITY AND FOG WITH CRUISE CONTROL ON FOR A TIME PERIOD OF AROUND 4 HOURS WITHOUT SPOOLING THE TURBO CHARGERS. UPON TRYING TO PASS ANOTHER VEHICLE THE GAS PEDAL WAS PRESSED TO ACCELERATE. VEHICLE BEGAN TO SHAKE VIOLENTLY, AND BEGAN TO LOSE POWER. VEHICLE WAS ABLE TO DRIVE AT CURRENT SPEED BUT WOULD SHAKE VIOLENTLY WHEN GAS WAS PRESSED TO PICK UP SPEED. THE CHECK ENGINE LIGHT DID ILLUMINATE. THIS ISSUE WAS CONSISTENT WITH THE ISSUE OF CONDENSATION/WATER IN THE CHARGE AIR COOLER CAUSING THE CYLINDERS TO MISFIRE AND VEHICLE GOING INTO LIMP MODE. THERE WAS NO ISSUE WHEN ATMOSPHERIC CONDITIONS WERE OPTIMAL. THIS HAPPENED AFTER THE FORD DEALERSHIP MADE THE RECOMMENDED FORD BULLETIN REPAIRS. THIS ISSUE HAS THE POTENTIAL OF CAUSING A FATALITY.
VEHICLE IS A FORD F150 2012 ECOBOOST V6 3.5L. VEHICLE WAS DRIVEN IN RAIN WITH CRUISE CONTROL ON FOR A TIME PERIOD OF AROUND 3 HOURS WITHOUT SPOOLING THE TURBO CHARGERS. UPON TRYING TO PASS ANOTHER VEHICLE THE GAS PEDAL WAS PRESSED TO ACCELERATE. VEHICLE BEGAN TO SHAKE VIOLENTLY, AND BEGAN TO LOSE POWER. THIS ACTION NEARLY CAUSED…
Read full complaint
VEHICLE IS A FORD F150 2012 ECOBOOST V6 3.5L. VEHICLE WAS DRIVEN IN RAIN WITH CRUISE CONTROL ON FOR A TIME PERIOD OF AROUND 3 HOURS WITHOUT SPOOLING THE TURBO CHARGERS. UPON TRYING TO PASS ANOTHER VEHICLE THE GAS PEDAL WAS PRESSED TO ACCELERATE. VEHICLE BEGAN TO SHAKE VIOLENTLY, AND BEGAN TO LOSE POWER. THIS ACTION NEARLY CAUSED A HEAD ON COLLISION. VEHICLE WAS ABLE TO DRIVE AT CURRENT SPEED BUT WOULD SHAKE VIOLENTLY WHEN GAS WAS PRESSED TO PICK UP SPEED. THIS HAPPENED TWICE IN THE SAME TRIP CAUSING THE CHECK ENGINE LIGHT TO ILLUMINATE. THIS ISSUE WAS CONSISTENT WITH THE ISSUE OF CONDENSATION/WATER IN THE CHARGE AIR COOLER CAUSING THE CYLINDERS TO MISFIRE AND VEHICLE GOING INTO LIMP MODE. THERE WAS NO ISSUE WHEN ATMOSPHERIC CONDITIONS WERE OPTIMAL. AGAIN, THIS ISSUE NEARLY CAUSED A HEAD ON COLLISION AS I TRIED TO PASS ANOTHER VEHICLE IN AN AREA WHICH ALLOWED PASSING IN MY LANE. FORD RE-FLASHED THE THE ECU AND ADDED A DEFLECTOR SHIELD TO THE TOP OF THE CHARGE AIR COOLER AND IT DID NOT FIX THE PROBLEM.
2012 ECOBOAST ENGINE UNEXPECTEDLY SHUTS DOWN WHEN I BEGIN TO ACCELLERATE M I BEGIN TO ACCELLERATE INTO MY LANE OR ACROSS ONCOMING TRAFFIC --- OR NO TRAFFIC. . MY SPEED RAPIDLY DECREASES DURING THIS 2 TO 5 SECOND "DELAY" AND HAS RESULTED IN MANY NEAR MISSES WHEN IN HEAVY TRAFFIC. ESPECIALLY DANGEROUS IS WHEN STUCK IN HEAVY STOP…
Read full complaint
2012 ECOBOAST ENGINE UNEXPECTEDLY SHUTS DOWN WHEN I BEGIN TO ACCELLERATE M I BEGIN TO ACCELLERATE INTO MY LANE OR ACROSS ONCOMING TRAFFIC --- OR NO TRAFFIC. . MY SPEED RAPIDLY DECREASES DURING THIS 2 TO 5 SECOND "DELAY" AND HAS RESULTED IN MANY NEAR MISSES WHEN IN HEAVY TRAFFIC. ESPECIALLY DANGEROUS IS WHEN STUCK IN HEAVY STOP & GO TRAFFIC, WHEN I MUST QUICKLY ADJUST BETWEEN THE GAS AND BRAKE TO PREVENT A CRASH. IN THIS HEAVY TRAFFIC SCENERIO, THE ENGINE WILL BEGIN TO " BACKFIRE" AND BRINGS ME TO A STOP IN THIS TRAFFIC --- AND THEN SUDDENLY "CATCHES ON" AND BRINGS ME TO A PANIC BRAKING OPTION. I'VE TAKEN THIS ISSUE TO MY FORD DEALERS OVER THE PAST 7 MONTHS, AND THEY HAVE NO SOLUTION --- ALTHOUGH ALL ARE AWARE OF SIMILAR COMPLAINTS SUCH AS MINE --- THEY EVEN HAVE A NAME FOR IT --- "LIMB MODE AND OR TURBO LAG." NHTSA HAS MANY SIMILAR SCENERIOS IN ITS CURRETN "COMPLAINT" LOG BUT NO INFO REGARDING THE STATUS OF THE COMPLAINTS. THIS CONDITION IS EXTREMELY DANGEROUS AND COULD RESULT IN INJURIES OR DEATHS.
JULY 6 LOST POWER TO TRUCK ENGINE AT 60 MPH WHEN GOING TO PASS IN HARD ACCELERATION SITUATION. TRUCK ENGINE SHUTTERED FOR OVER 3 MINS UNTIL I COULD GET IT STABILIZED AROUND 2000 RPMS IN A LOWER GEAR/SPEED. THIS WAS THE FIRST OF TWO SIMILAR SITUATION ON THE SAME DAY WITH THE TRUCK AND THROUGHOUT THE REMAINDER OF THE DAY ANY AC…
Read full complaint
JULY 6 LOST POWER TO TRUCK ENGINE AT 60 MPH WHEN GOING TO PASS IN HARD ACCELERATION SITUATION. TRUCK ENGINE SHUTTERED FOR OVER 3 MINS UNTIL I COULD GET IT STABILIZED AROUND 2000 RPMS IN A LOWER GEAR/SPEED. THIS WAS THE FIRST OF TWO SIMILAR SITUATION ON THE SAME DAY WITH THE TRUCK AND THROUGHOUT THE REMAINDER OF THE DAY ANY ACCELERATION OVER 3500 RPMS CAUSED A LOSS OF POWER. WE LIMPED THE VEHICLE HOME THAT DAY. NEXT DAY CHECK ENGINE LIGHT CAME ON AND OFF UNTIL WE COULD GET TRUCK INTO OUR LOCAL FORD DEALER FOR SERVICE ON 7-13. THIS ISSUE HAS BEEN RESEARCHED VIA INFO ON THIS SITE TO NO CONCLUSION. I CAN SAY IF YOU DROVE THIS VEHICLE AND SIMULATED THIS ISSUE YOU WOULD SEE THE MAJOR ISSUE THIS CAUSES AND POTENTIAL RISK OF ACCIDENT AT HIGHWAY SPEEDS WITH ACCELERATION. SPECIFICALLY HEAVY TRAFFIC SITUATIONS. THE ISSUE CAUSED SPARK PLUG DAMAGE, CATALYTIC CONVERTER DAMAGE AND THE DEALER PERFORMED THE TSB (4TH ISSUED BY FORD) TO ATTEMPT TO FIX THE ISSUE. THIS IS A KNOWN ISSUE, CAUSES SAFETY ISSUES AND SHOULD BE RECALLED TO PERMANENTLY FIX NOT TRY TO PATCH WITH FOUR DIFFERENT TSB. FIX THIS CORRECTLY BEFORE ACCIDENTS OCCUR THAT CAUSE DEATHS. UPDATED 9/25/15 *LN UPDATED 3/23/2016*JS UPDATED 11/27/2017*CN
ENGINE FAILED TO ACCELERATE WHEN ATTEMPTING TO MERGE INTO TRAFFIC ON INTERSTATE, ALMOST CAUSING AN ACCIDENT. ENGINE STARTED SHAKING AND CHECK ENGINE LIGHT CAME ON. IT HAD BEEN RAINING AND WAS VERY WET. AFTER PULLING OFF TURNED OF ENGINE FOR APPROX 15 MINUTES. STARTED DRIVING AGAIN AND DID NOT EXPERIENCE ANY OTHER PROBLEMS.
24,991MI: MISFIRE WHEN ACCELERATING WHILE DRIVING. NO CHECK ENGINE LIGHT. DEALER REPORTED NO PROBLEM FOUND, NO CODES & MADE NO REPAIRS. 29,440MI: MISFIRE WHEN ACCELERATING & GOING UP & DOWN HILLS SPECIFICALLY WHEN IN 4,5, 6 GEAR DURING BOTH FLAT & INCLINED HIGHWAY DRIVING. THIS WAS WHILE PULLING AN 8000LB TRAILER. NO CHECK ENGI…
Read full complaint
24,991MI: MISFIRE WHEN ACCELERATING WHILE DRIVING. NO CHECK ENGINE LIGHT. DEALER REPORTED NO PROBLEM FOUND, NO CODES & MADE NO REPAIRS. 29,440MI: MISFIRE WHEN ACCELERATING & GOING UP & DOWN HILLS SPECIFICALLY WHEN IN 4,5, 6 GEAR DURING BOTH FLAT & INCLINED HIGHWAY DRIVING. THIS WAS WHILE PULLING AN 8000LB TRAILER. NO CHECK ENGINE LIGHT. DEALER FOUND MISFIRE IN #1 & 4 AND REPLACED COILS & PLUGS IN #1 & #4 ONLY. TEST DRIVE STILL SHOWED MISFIRE, THEN REPLACED TURBO BOOST PRESSURE SENSOR. I WAS TOLD THAT MOISTURE HAD DAMAGED THE PLUGS & SENSOR. 35,214MI: MISFIRE WHEN TAKING OFF FROM A STOP, DURING NORMAL ACCELERATION AND GOING UP HILLS.NO CHECK ENGINE LIGHT. DEALER REPLACED THE DRIVERS SIDE EXHAUST MANIFOLD BECAUSE IT WAS WARPED. 37,164MI: MISFIRE WHEN TAKING OFF FROM A STOP, DURING NORMAL ACCELERATION & GOING UP HILLS. I SAW THIS IN ACCELERATION CONDITIONS FROM 10-60MPH WITHOUT TOWING A TRAILER. NO CHECK ENGINE LIGHT. DEALER REPORTED NO PROBLEM FOUND, NO CODES & MADE NO REPAIRS. 38,577MI: REPEATED SEVERE MISFIRES WHILE GOING UP MODERATE INCLINES. CHECK ENGINE LIGHT CAME ON (FIRST TIME THIS EVER HAPPENED) & I HAD A REDUCTION IN POWER, COULD NOT GET OUT OF 3RD GEAR & MY SPEED DROPPED FROM 65MPH TO 50MPH. AFTER REPAIR HAD MODERATE MISFIRES DURING MAJOR INCLINES WHILE TOWING A TRAILER BUT NO CHECK ENGINE LIGHT. 39,000MI: WHILE TOWING A TRAILER, EXPERIENCED SERIES OF MODERATE TO SEVERE MISFIRES IN WAVES BE OK FOR AN HOUR & THEN GO INTO A SERIES OF MISFIRES FOR 3-10 MINUTES. SOME WERE ON HILLS, SOME WERE ON FLAT HIGHWAY DRIVING. I HAD 5 OCCURRENCES WHERE THE CHECK ENGINE LIGHT CAME ON DURING THIS DRIVE. 3 OF THESE WERE DURING A HILL CLIMB WHERE I HAD A POWER REDUCTION & LOST SPEED. VEHICLE STAYED IN 3RD GEAR. WHEN I WOULD GET A SERIES OF SEVERE MISFIRES, MISFIRES WERE SO SEVERE (WITHOUT THE CHECK ENGINE LIGHT ON), THAT I COULD HEAR & FEEL THE TURBO KICK OFF & ON..
I PURCHASED THIS VEHICLE FOR MY SON IN DECEMBER 2012. WE TOOK A TRIP TO ALABAMA ON THE SATURDAY FOLLOWING THE PURCHASE. THE TRUCK HAD PROBLEMS STALLING, MISFIRIING, AND NOT BRAKING IMMEDIATELY. WE HAVE TAKEN THE TRUCK TO THE FORD DEALERSHIP FOR REPAIRS APPROXIMATELY 15 TO 20 TIMES. IT IS IN THE SHOP AGAIN TODAY FOR THE MISFIRING…
Read full complaint
I PURCHASED THIS VEHICLE FOR MY SON IN DECEMBER 2012. WE TOOK A TRIP TO ALABAMA ON THE SATURDAY FOLLOWING THE PURCHASE. THE TRUCK HAD PROBLEMS STALLING, MISFIRIING, AND NOT BRAKING IMMEDIATELY. WE HAVE TAKEN THE TRUCK TO THE FORD DEALERSHIP FOR REPAIRS APPROXIMATELY 15 TO 20 TIMES. IT IS IN THE SHOP AGAIN TODAY FOR THE MISFIRING/STALLING. THE SERVICE WRITER TOLD MY SON THAT HIS VEHICLE HAS ONLY BEEN THE SHOP TWICE FOR THE SAME PROBLEM. WE STILL HAVE ALL THE SERVICE PAPERWORK TO DISPEL THAT REMARK, THIS VEHICLE HAS APPROXIMATELY 24,000 MILES ON IT. THE FACTORY WARRANTY EXPIRES IN DECEMBER AND HAS STILL NOT BEEN FIXED. IT DOES NOT JUST STALL IN RAINY OR VERY HUMID CONDITIONS AS STATED BY FORD IN THEIR RESPONSE TO THE NHTSA INVESTIGATION. THEY HAVE REPLACED SPARK PLUGS TWICE, UPDATED SOFTWARE, PUT A HEAT SHIELD IN FRONT OF THE INTER-COOLER. NONE OF THESE THINGS HAVE WORKED. THE SHIELD IN FRONT OF THE INTER-COOLER DEFEATS THE PURPOSE OF THE INTER-COOLER BY NOT ALLOWING IT TO COOL AS INTENDED. IT RAISES THE TEMPERATURE IN THE INTERCOOLER IN AN ATTEMPT TO PRODUCE LESS CONDENSATION. MY SON BELIEVES THE INTER-COOLER HAS A DESIGN FLAW. HE THINKS THAT THE AIR RETURN FROM THE INTER-COOLER TO THE ENGINE BEING ON THE BOTTOM ALLOWS MORE CONDENSATION TO BE SUCKED BACK INTO THE ENGINE. IF IT WERE ON THE TOP, MORE OF THE CONDENSATION WOULD STAY IN THE BOTTOM AND NOT RETURNED BACK TO THE ENGINE. THERE IS AN AFTER MARKET FIX FOR THIS PROBLEM BUT IT IS EXPENSIVE AND I BELIEVE FORD MOTOR COMPANY DOES NOT WANT TO SPEND THE KIND OF MONEY THAT IT WILL TAKE TO FIX THIS PROBLEM CORRECTLY. THIS VEHICLE SHOULD BE ABLE TO OPERATE EFFICIENTLY UNDER ANY CONDITIONS. IF IT DOES NOT, IT IS FLAWED. I WILL PROBABLY HAVE TO PURCHASE THE REPLACEMENT INTER-COOLER OUT OF MY OWN POCKET. I'VE INCLUDED ALL THIS INFORMATION IN THE EVENT THAT IT HELPS OTHERS WITH THE SAME PROBLEM.
WHEN ATTEMPTING TO ACCELERATE FROM A COMPLETE STOP THE TRUCK WILL ONLY MOVE FORWARD WHEN THE PEDAL IS FULLY DEPRESSED. WHEN THIS IS HAPPENING THE TRUCK BARELY MOVES THEN IT WILL CATCH AND LUNGE FORWARD AT BREAK-NECK SPEED. THIS SAME THING HAPPENS AT APPROXIMATELY 30 MPH, WILL BE ACCELERATING NORMALLY WHEN ALL THE SUDDEN THE RPM …
Read full complaint
WHEN ATTEMPTING TO ACCELERATE FROM A COMPLETE STOP THE TRUCK WILL ONLY MOVE FORWARD WHEN THE PEDAL IS FULLY DEPRESSED. WHEN THIS IS HAPPENING THE TRUCK BARELY MOVES THEN IT WILL CATCH AND LUNGE FORWARD AT BREAK-NECK SPEED. THIS SAME THING HAPPENS AT APPROXIMATELY 30 MPH, WILL BE ACCELERATING NORMALLY WHEN ALL THE SUDDEN THE RPM AND SPEED GAUGES COMPLETELY DROP THE ENGINE LOSSES ALL POWER AND IF THE PEDAL IS CONTINUED TO BE PRESSED THE TRUCK WILL LUNGE FORWARD, AGAIN AT BREAK-NECK SPEED. IN A 10 MILE TRIP IT CAN HAPPEN 3 OR 4 TIMES. TODAY WE HAD A NEW EXPERIENCE WHERE WHEN DECELERATING TO COME TO A COMPLETE STOP THE MOTOR BEGAN REVVING TO REDLINE ALL WHILE ONLY THE BRAKE WAS DEPRESSED. ON GREEN LIGHT THE ACCELERATION AGAIN WAS LIMITED TO FULL PETAL AND A LIMP TILL BURST MODE. THESE EVENTS ALL SCARE THE FAMILY TO THE POINT OF NOT RIDING IN THE VEHICLE.
I PURCHASED THIS 2012 FORD F-150 BRAND NEW!!! I AM A DIE HARD FORD FAN, AND HAVE NEVER BOUGHT SOMETHING NEW, SO AFTER MANY OLD PREOWNED FORD TRUCKS, I BOUGHT A NEW F-150. UNDER BOTH THE 36,000 MILES AND 3 YEAR BUMPER TO BUMPER WARRANTY, IT WOULD RATTLE, SHAKE, AND TICK A LOT, A WHOLE LOT! IT WOULD ALSO MAKE A LOUD RATTLI…
Read full complaint
I PURCHASED THIS 2012 FORD F-150 BRAND NEW!!! I AM A DIE HARD FORD FAN, AND HAVE NEVER BOUGHT SOMETHING NEW, SO AFTER MANY OLD PREOWNED FORD TRUCKS, I BOUGHT A NEW F-150. UNDER BOTH THE 36,000 MILES AND 3 YEAR BUMPER TO BUMPER WARRANTY, IT WOULD RATTLE, SHAKE, AND TICK A LOT, A WHOLE LOT! IT WOULD ALSO MAKE A LOUD RATTLING NOISE DURING A COLD START, OR BETWEEN 1800-2000 RPM. AFTER DOING MY HOMEWORK, THIS 3.5 LITER ENGINE (ECOBOOST) HAS TIMING CHAIN ISSUES AND THE TIMING CHAIN HAS BEEN KNOWN FOR PRE-MATURE STRETCH. I FOUND 4 OTHER TESTIMONIALS OF THE SAME EXACT ISSUE WITH THE TIMING CHAIN. IT GETS BETTER, THE OTHER PEOPLE WERE ALSO TOLD THE SAME THING AFTER BRINGING IT TO THEIR FORD DEALER FOR REPAIR. THEY SAID "FORD IS AWARE OF THE ISSUE, BUT IT WOULD NOT AFFECT LONG TERM OPERATION OF THE VEHICLE, AND FORD DEEMS IT ACCEPTABLE; NO REPAIR NECESSARY".........WOW!!!!!! AFTER SPENDING ALMOST 40K ON MY FIRST NEW TRUCK. I THEN WENT TO CALL FORD COOPERATE WHERE I CLIMBED UP THE LADDER OF 3 DIFFERENT MANAGERS, EACH OF HIGHER RANKING, AND THE WROTE THE HIGHEST CUSTOMER SERVICE OFFICIAL A LETTER, ONLY TO BE TOLD NO, NOTHING COULD BE DONE.
Official recalls
419V075000 · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Feb 11, 2019
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Power Train:automatic Transmission
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
16V248000 · Power Train:automatic Transmission
Apr 27, 2016
Ford Motor Company (Ford) is recalling certain model year 2011-2012 Ford F-150 trucks, 2012 Ford Expedition, Lincoln Navigator, and Ford Mustang vehicles. The affected vehicles are equipped with an automatic transmission that may unexpectedly downshift to first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: An unexpected downshift into first gear can cause the vehicle to slow down suddenly without warning and the rear tires may slide or lock, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module with updated software, free of charge. The recall began on September 19, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S19.
12V190000 · Exterior Lighting:back Up Lights; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence & remedy
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Additional source detail variants (2)
Exterior Lighting:back Up Lights
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
12V198000 · Air Bags:frontal:sensor/control MODULE-INACTIVE
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2012 F-150 VEHICLES MANUFACTURED FROM NOVEMBER 6, 2011, THROUGH NOVEMBER 15, 2011. INCORRECT SOFTWARE FOR THE OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) WAS INSTALLED ON THE VEHICLES EITHER AT THE TIME OF MANUFACTURING OR DURING THE COURSE OF REPLACEMENT OF THE MODULE AS PART OF A SERVICE REPAIR. UNDER CERTAIN DRIVING CONDITIONS, THE OCSM MAY MISCLASSIFY THE PASSENGER SEATS OCCUPANT SUCH THAT THE PASSENGER SIDE AIRBAG DOES NOT DEPLOY WHEN IT SHOULD, DOES NOT DEPLOY AS INTENDED, OR DEPLOYS WHEN IT SHOULD NOT.
Consequence & remedy
Consequence: A FAILURE TO DEPLOY, FAILURE TO DEPLOY AS INTENDED, OR A DEPLOYMENT WHEN NOT INTENDED, INCREASES THE RISK OF INJURY TO THE PASSENGER SIDE SEAT OCCUPANT.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE OCSM FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 21, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4RQ17010 · Unexpected Transmission Downshift
Opened Dec 25, 2017 · Closed Oct 22, 2019
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
EA15006 · Brake Vacuum Pump Failure
Opened Oct 16, 2015 · Closed Apr 28, 2016
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Additional source detail variants (3)
Service Brakes, Electric
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
PE15026 · Brake Vacuum Pump Failure
Opened Jun 22, 2015 · Closed Oct 19, 2015
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Additional source detail variants (3)
Service Brakes, Electric
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
PE13018 · Reduced Power During Hard Acceleration
Opened May 22, 2013 · Closed Apr 7, 2014
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Additional source detail variants (2)
Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Engine
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of