NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
288 reportsMileage unknown · Jun 29, 2026
Unknown Or Other
The panoramic sunroof cover, it is available for inspection upon request my safety was jeopardized while driving my car at the time, the problem has not been reproduced, but it has been confirmed by dealer the Ford dealer told me that it would cost me $2000 plus a $200 labor fee to get it repaired and I did tell him that I had l…
Read full complaint
The panoramic sunroof cover, it is available for inspection upon request my safety was jeopardized while driving my car at the time, the problem has not been reproduced, but it has been confirmed by dealer the Ford dealer told me that it would cost me $2000 plus a $200 labor fee to get it repaired and I did tell him that I had looked on a site and saw that this happened happened to a lot of Ford escape buyers. There weren’t any warnings as I was driving, and I pushed the button to open up the sunroof. The cover just flapped and went all the way back as I was driving and came off of the track and the black plastic part that’s in the middle fell down and I could never get that to stick back up again. I first noticed when I would have my sunroof slanted. I never would open it all the way, but just slanted. I would hear a rattling noise so I would close it and I opened my sunroof all the way up twice and the third time when I decided to open it all the way up while I was driving that’s when the whole thing just fell, fell the middle black part and the cover while I was driving and it scared the daylights out of me while I was driving on the road.
NHTSA ODI #11747278
79,000 miles · Apr 30, 2026
Back Over Prevention
The contact owns a 2020 Ford Escape. The contact received notification of NHTSA Campaign Number: 26V123000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted but the vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable a…
Read full complaint
The contact owns a 2020 Ford Escape. The contact received notification of NHTSA Campaign Number: 26V123000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted but the vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the sync screen intermittently displayed an inverted image. The contact added that the inability to properly use the display posed a safety risk, as it may increase the likelihood of a crash. The approximate failure mileage was 79,000.
NHTSA ODI #11734867
Mileage unknown · Aug 22, 2025
Engine
Sluggish acceleration, car would not go faster than 37 MPH at full throttle, appeared to be running on hybrid motor only, not on engine power. 2020 Ford Escape Hybrid. 2.5 L engine. Only got 1 mile, returned home. No smoke, no fire, just not accelerating. Car was completely fine the day before. Got towed to Ford dealer next morn…
Read full complaint
Sluggish acceleration, car would not go faster than 37 MPH at full throttle, appeared to be running on hybrid motor only, not on engine power. 2020 Ford Escape Hybrid. 2.5 L engine. Only got 1 mile, returned home. No smoke, no fire, just not accelerating. Car was completely fine the day before. Got towed to Ford dealer next morning.
NHTSA ODI #11682471
38,000 miles · Mar 19, 2025
Engine And Engine Cooling
The contact owns a 2020 Ford Escape. The contact stated that while driving at various speeds, an abnormal coolant consumption was noticed. No warning light was illuminated. The vehicle was taken to a local dealer to be diagnosed; however, the cause of the failure was not determined. The vehicle was not repaired. The manufacturer…
Read full complaint
The contact owns a 2020 Ford Escape. The contact stated that while driving at various speeds, an abnormal coolant consumption was noticed. No warning light was illuminated. The vehicle was taken to a local dealer to be diagnosed; however, the cause of the failure was not determined. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 38,000.
NHTSA ODI #11649296
Mileage unknown · Mar 18, 2025
Unknown Or Other
I recently found out through a Ford dealer that there was a recall on the door on my Ford escape. I never received anything in the mail. I had the issue fixed by my local mechanic and he used Ford parts. I would like A reimbursement.
NHTSA ODI #11648987
60,000 miles · Feb 28, 2025
Structure
The contact owns a 2020 Ford Escape Hybrid. The contact stated that while operating the vehicle, there was an abnormally strong odor of mold and mildew was inside the cabin of the vehicle. The vehicle was taken to the local dealer who discovered that rainwater had leaked into the trunk and spare tire well, causing mold and milde…
Read full complaint
The contact owns a 2020 Ford Escape Hybrid. The contact stated that while operating the vehicle, there was an abnormally strong odor of mold and mildew was inside the cabin of the vehicle. The vehicle was taken to the local dealer who discovered that rainwater had leaked into the trunk and spare tire well, causing mold and mildew to develop inside the vehicle. The contact was informed that the carpet needed to be replaced. The exact cause of the water intrusion was unknown. The vehicle was not yet repaired. There was no illness or sickness reported. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 60,000. The VIN was not available.
NHTSA ODI #11645477
Mileage unknown · Feb 25, 2025
Electrical SystemPower Train
The vehicle is just under 37K miles. I was operating the vehicle normally, and the wrench icon came on, indicating a powertrain issue. There are recalls for this for some vehicles but not all, and it seems to occur just after warranties expiring. I am concerned my vehicle falls under this service bulletin but has not been proper…
Read full complaint
The vehicle is just under 37K miles. I was operating the vehicle normally, and the wrench icon came on, indicating a powertrain issue. There are recalls for this for some vehicles but not all, and it seems to occur just after warranties expiring. I am concerned my vehicle falls under this service bulletin but has not been properly added: SSM 49157 - 2020 Escape - Illuminated MIL With DTCs U0100, U0401, P166B, P1753, P0929, And/Or P0919 Some 2020 Escape vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) U0100, U0401, P166B, P1753, P0929, and/or P0919. The vehicle may also exhibit an illuminated powertrain malfunction (wrench) indicator lamp. This may be due to the software in the gear shift module (GSM). To correct the condition, reprogram the GSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part number 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. APPLICABLE VEHICLES 2020 CAR: TC CX482N ESCAPE 2020 CAR: TC CX482N ESCAPE 2020 CAR: TC CX482N ESCAPE
NHTSA ODI #11644872
Mileage unknown · Jan 29, 2025
Unknown Or OtherVisibility/wiper
The sunroof cover came down and blocked my rear visibility. It took a few attempts to get the cover back up because I need to see what is behind me for safety purposes. Then, when I was sesrching online for the solution, I realized a lot of people with 2020 - 2022 Ford Escapes were also having issues with the sunroof cover. It i…
Read full complaint
The sunroof cover came down and blocked my rear visibility. It took a few attempts to get the cover back up because I need to see what is behind me for safety purposes. Then, when I was sesrching online for the solution, I realized a lot of people with 2020 - 2022 Ford Escapes were also having issues with the sunroof cover. It is quite dangerous for it to fall.
NHTSA ODI #11639520
Mileage unknown · Dec 31, 2024
Electrical System
The hybrid battery coolant line has a leak and is available for inspection. Driving the vehicle with this leak can compromise the battery resulting in overheating which could cause the vehicle to break down, fire, or burn. The dealer confirmed the leak. The dealer was a manufacturer dealer and they inspected the vehicle. There …
Read full complaint
The hybrid battery coolant line has a leak and is available for inspection. Driving the vehicle with this leak can compromise the battery resulting in overheating which could cause the vehicle to break down, fire, or burn. The dealer confirmed the leak. The dealer was a manufacturer dealer and they inspected the vehicle. There were no indications of a leak.
NHTSA ODI #11633447
Mileage unknown · Dec 14, 2024
Unknown Or OtherVisibility/wiper
The car has a panoramic roof with automatic open/close sunshade that cover the interior of the glass. I was opening the sunshade to open the moon roof and the shade all of the suden came down and did not roll as intended and my visibility while I was driving was gone for a second until my wife helped out quickly so we do not cra…
Read full complaint
The car has a panoramic roof with automatic open/close sunshade that cover the interior of the glass. I was opening the sunshade to open the moon roof and the shade all of the suden came down and did not roll as intended and my visibility while I was driving was gone for a second until my wife helped out quickly so we do not crash. The problem is common for this car in the ford forums online and the dealerships are not concerend or applying any responsbility of the problem and the safety of it. there was no message or warning but it put myself and my family in danger. I went and got it inspected by the dealership but they did not take responsibilty.
NHTSA ODI #11630667
NHTSA investigations
2PE23013 · Failed Door Check Arm Attachment Point
Opened Jul 7, 2023 · Closed Jan 24, 2024
Status: closed (inferred from source dates) · Structure:body:door ; Structure:body:door:hinge And Attachments
On July 7, 2023, the Office of Defects Investigation (ODI) opened PE23-013 to investigate instances of check arm bracket failure in the front doors in model year (MY) 2020-2021 Ford Escape vehicles. At the time of opening, ODI received 118 Vehicle Owner Questionnaires (VOQs) alleging this failure. To date, ODI has received 593 VOQs alleging this failure, with a variety of reported failure conditions. The most common reported failure condition was reduced door functionality (e.g. door was more difficult to open or close) and the least common was inadvertent door opening. Other reported failure conditions include inability to latch and inability to open. Three VOQs reported injuries, one of which requiring medical attention. ODI conducted a consumer survey which yielded an additional 44 injuries (although the VOQs did not indicate any injury), none of which requiring medical attention. All these injuries were bumps/bruises from the door closing on occupants’ arms and legs while entering and exiting the vehicle. The function of the check arm system is to provide hold-open assist at specific angles and to assist with door closing energy. It does not provide vertical support of the door and is independent of the latching mechanism. This failure is progressive and detectable by vehicle occupants. Consumers commonly report hearing a popping or snapping noise when opening and closing the door. This noise is caused by some of the welds between the bracket and door structure failing and detaching. There may also be visible damage present to the welds in the door structure. Continued use of the door may result in all welds separating and the bracket fully detaching from the door structure, which could lead to increased resistance in closing and opening the door, restrained window operation, and the door freely rotating when open. ODI inspected 3 consumer vehicles in the field, and 2 test vehicles at Ford’s testing facility. The test vehicles were retrofitted with the failed component. ODI observed an increased door closing resistance, however, was unable to reproduce an inadvertent open while parked or driving, or a failure to latch or open condition. Testing also verified this failure did not affect the door ajar warning system. This system provides an audible and visual warning in the event a door did not achieve primary latch position. Ford has provided details on a one-time-repair customer satisfaction program (23B56), stating that they will provide customers with a letter, currently targeted for March 2024, to bring their vehicle to a Ford dealership for a proactive repair. Dealers will inspect the door check arm welds for damage and will either provide a rivet plate to reinforce the existing door check arm or will provide a replacement door, depending on the level of damage present. Customers will be eligible for reimbursement if they previously paid to repair this issue. In view of the high detectability of failure, low potential hazard to drivers, and Ford’s customer satisfaction program to provide a proactive repair, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Structure:body:door
On July 7, 2023, the Office of Defects Investigation (ODI) opened PE23-013 to investigate instances of check arm bracket failure in the front doors in model year (MY) 2020-2021 Ford Escape vehicles. At the time of opening, ODI received 118 Vehicle Owner Questionnaires (VOQs) alleging this failure. To date, ODI has received 593 VOQs alleging this failure, with a variety of reported failure conditions. The most common reported failure condition was reduced door functionality (e.g. door was more difficult to open or close) and the least common was inadvertent door opening. Other reported failure conditions include inability to latch and inability to open. Three VOQs reported injuries, one of which requiring medical attention. ODI conducted a consumer survey which yielded an additional 44 injuries (although the VOQs did not indicate any injury), none of which requiring medical attention. All these injuries were bumps/bruises from the door closing on occupants’ arms and legs while entering and exiting the vehicle. The function of the check arm system is to provide hold-open assist at specific angles and to assist with door closing energy. It does not provide vertical support of the door and is independent of the latching mechanism. This failure is progressive and detectable by vehicle occupants. Consumers commonly report hearing a popping or snapping noise when opening and closing the door. This noise is caused by some of the welds between the bracket and door structure failing and detaching. There may also be visible damage present to the welds in the door structure. Continued use of the door may result in all welds separating and the bracket fully detaching from the door structure, which could lead to increased resistance in closing and opening the door, restrained window operation, and the door freely rotating when open. ODI inspected 3 consumer vehicles in the field, and 2 test vehicles at Ford’s testing facility. The test vehicles were retrofitted with the failed component. ODI observed an increased door closing resistance, however, was unable to reproduce an inadvertent open while parked or driving, or a failure to latch or open condition. Testing also verified this failure did not affect the door ajar warning system. This system provides an audible and visual warning in the event a door did not achieve primary latch position. Ford has provided details on a one-time-repair customer satisfaction program (23B56), stating that they will provide customers with a letter, currently targeted for March 2024, to bring their vehicle to a Ford dealership for a proactive repair. Dealers will inspect the door check arm welds for damage and will either provide a rivet plate to reinforce the existing door check arm or will provide a replacement door, depending on the level of damage present. Customers will be eligible for reimbursement if they previously paid to repair this issue. In view of the high detectability of failure, low potential hazard to drivers, and Ford’s customer satisfaction program to provide a proactive repair, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Structure:body:door:hinge And Attachments
On July 7, 2023, the Office of Defects Investigation (ODI) opened PE23-013 to investigate instances of check arm bracket failure in the front doors in model year (MY) 2020-2021 Ford Escape vehicles. At the time of opening, ODI received 118 Vehicle Owner Questionnaires (VOQs) alleging this failure. To date, ODI has received 593 VOQs alleging this failure, with a variety of reported failure conditions. The most common reported failure condition was reduced door functionality (e.g. door was more difficult to open or close) and the least common was inadvertent door opening. Other reported failure conditions include inability to latch and inability to open. Three VOQs reported injuries, one of which requiring medical attention. ODI conducted a consumer survey which yielded an additional 44 injuries (although the VOQs did not indicate any injury), none of which requiring medical attention. All these injuries were bumps/bruises from the door closing on occupants’ arms and legs while entering and exiting the vehicle. The function of the check arm system is to provide hold-open assist at specific angles and to assist with door closing energy. It does not provide vertical support of the door and is independent of the latching mechanism. This failure is progressive and detectable by vehicle occupants. Consumers commonly report hearing a popping or snapping noise when opening and closing the door. This noise is caused by some of the welds between the bracket and door structure failing and detaching. There may also be visible damage present to the welds in the door structure. Continued use of the door may result in all welds separating and the bracket fully detaching from the door structure, which could lead to increased resistance in closing and opening the door, restrained window operation, and the door freely rotating when open. ODI inspected 3 consumer vehicles in the field, and 2 test vehicles at Ford’s testing facility. The test vehicles were retrofitted with the failed component. ODI observed an increased door closing resistance, however, was unable to reproduce an inadvertent open while parked or driving, or a failure to latch or open condition. Testing also verified this failure did not affect the door ajar warning system. This system provides an audible and visual warning in the event a door did not achieve primary latch position. Ford has provided details on a one-time-repair customer satisfaction program (23B56), stating that they will provide customers with a letter, currently targeted for March 2024, to bring their vehicle to a Ford dealership for a proactive repair. Dealers will inspect the door check arm welds for damage and will either provide a rivet plate to reinforce the existing door check arm or will provide a replacement door, depending on the level of damage present. Customers will be eligible for reimbursement if they previously paid to repair this issue. In view of the high detectability of failure, low potential hazard to drivers, and Ford’s customer satisfaction program to provide a proactive repair, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration