NHTSA owner reports · September 18, 2026 snapshot.
Unknown Or Other complaints
64 reportsClear category filterMileage unknown · Jul 10, 2023
StructureUnknown Or Other
My front left drivers side door wouldnt close, I noticed the spot welds holding the door strap component in place had broke free and was now being pushed into the door shell. I took my car to the dealership and they said it is not covered. I have since looked on line, on how to repair this defect and see this is a known issue to…
Read full complaint
My front left drivers side door wouldnt close, I noticed the spot welds holding the door strap component in place had broke free and was now being pushed into the door shell. I took my car to the dealership and they said it is not covered. I have since looked on line, on how to repair this defect and see this is a known issue to the make and model year of my vehicle.
NHTSA ODI #11531410
Mileage unknown · Jun 28, 2023
Unknown Or Other
Vehicle would not shift out of park from a cold start. Dial shifter would not rotate. Vehicle could start but could not be driven. Problem has not been confirmed by dealer or independent service center. There were no warnings. Vehicle had been sitting in the sun in a parking lot on an 89 degree day for two hours. Cooling the ve…
Read full complaint
Vehicle would not shift out of park from a cold start. Dial shifter would not rotate. Vehicle could start but could not be driven. Problem has not been confirmed by dealer or independent service center. There were no warnings. Vehicle had been sitting in the sun in a parking lot on an 89 degree day for two hours. Cooling the vehicle cabin with A/C for 1/2 hour allowed the dial shifter to operate.
NHTSA ODI #11529267
Mileage unknown · Jun 16, 2023
Unknown Or Other
THE "SPOT WELD" ON THE DRIVERS SIDE DOOR FAILED NOT ALLOWING THE DRIVERS SIDE DOOR TO OPEN OR CLOSE. THIS PROBLEM IS OCCURING ON BOTH THE FORD EDGE AND FORD ESCAPE ACCORDING TO JARRETT'S REPAIR PEOPLE. MINE IS A 2020 ESCAPE AND CANNOT BE REPAIRED. FORD WILL NOT ALLOW IT, AND WILL ONLY FIX IT IF IT FALLS UNDER THE 3 YR, 36000 P…
Read full complaint
THE "SPOT WELD" ON THE DRIVERS SIDE DOOR FAILED NOT ALLOWING THE DRIVERS SIDE DOOR TO OPEN OR CLOSE. THIS PROBLEM IS OCCURING ON BOTH THE FORD EDGE AND FORD ESCAPE ACCORDING TO JARRETT'S REPAIR PEOPLE. MINE IS A 2020 ESCAPE AND CANNOT BE REPAIRED. FORD WILL NOT ALLOW IT, AND WILL ONLY FIX IT IF IT FALLS UNDER THE 3 YR, 36000 PART OF THE WARRANTY. MINE IS OUTSIDE OF THE 36 MONTH WARRANTY AND THEY WANT TO BILL ME OVER $2000 TO REPAIR IT BY BUYING A NEW DOOR, NOT ACCEPTABLE. THIS IS A MANUFACTURER DEFECT AND FORD SHOULD FIX IT, WELDS SHOULD NOT FAIL.
NHTSA ODI #11527432
Mileage unknown · Jun 3, 2023
Unknown Or Other
I was opening the front driver’s side door, the door failed to open completely. I had to forcefully pull the door handle for the door to open and heard a loud clicking noise. Took car to dealer and became aware that the latch was welded incorrectly and welded area broke. The dealer stated that the front driver’s side door need…
Read full complaint
I was opening the front driver’s side door, the door failed to open completely. I had to forcefully pull the door handle for the door to open and heard a loud clicking noise. Took car to dealer and became aware that the latch was welded incorrectly and welded area broke. The dealer stated that the front driver’s side door needed to be replaced. The vehicle was not repaired because the door cost is $2,500 and my warranty had just expired 4-30-23. I called Ford customer service to tell them the door check broke out of door to see if they had some assistance for the cost. They said they did not. The failure mileage was 32,100. You can see with the pictures attached the right front door bracket is not broke and the Drivers side front door bracket is broke with three welding holes that broke off the bracket. The bracket cost $47 to $50, but they say the whole door needs to be replaced. $2500 cost is not fair to a owner when a small part breaks with the only fix and whole new door. If all four of my doors break soon the cost would be $10,000.00. This needs to be considered a RECALL so Ford can fix and bare the cost for a part that has gone bad and there are many complaints on this same issue. Thanks for looking into it.
NHTSA ODI #11525172
Mileage unknown · May 22, 2023
Unknown Or Other
The driver's side front check arm welds inside the door broke loose, and the door can't be closed.
NHTSA ODI #11523290
Mileage unknown · May 13, 2023
Unknown Or Other
On the drivers side doir, the 3 spot welds for the door stop failed. Now it makes a horrible cracking sound. I was told the whole door needs to be replaced and I'm out of warranty. I've had the vehicle just over 3 years.
NHTSA ODI #11521860
Mileage unknown · Oct 12, 2022
Electrical SystemEngineUnknown Or OtherFire
On June7th I was driving home in my 2020 hybrid escape when the motor quit and the car came to a stop, then smoke started coming out from under the hood, I opened the hood and flames shot out at the back side of the motor on the passenger side, oil was leaking on to the road and on fire, I called the fire department, when they g…
Read full complaint
On June7th I was driving home in my 2020 hybrid escape when the motor quit and the car came to a stop, then smoke started coming out from under the hood, I opened the hood and flames shot out at the back side of the motor on the passenger side, oil was leaking on to the road and on fire, I called the fire department, when they got there all the fire finally went out as the oil burned up. I had the car towed that day to Purchase ford in Mayfield KY. where it is still at. At first I was told this would be a warranty covered job, the car had 37500 miles, the power train and motor are good for 60,000 miles. It was apparent this would take a long time to fix, and I told Ford I did not want the car back as it would be depleted in value with a history of a fire, In July I got a recall 22V484 for the very reason my car caught on fire. Come to find out the motor failed and thru a rod and a hole in the block let the oil leak out and catch on fire. I asked for a loaner but they did not have one, I rented a car and Ford finally paid for most of it but I'm still out $500.00, I have returned the rental car. I have made five months of payment on this car without having it. At first Ford said they would do a buy back, then they emailed me saying this was denied due to KY. guidelines? I also asked for another car of equal value and that will not happen. Finally Ford told me to accept the repairs on my car and take it back or they were closing my case. My case # is [XXX], my contact was customer service rep . [XXX]. The car has a value of about $25000.00 if it had not caught on fire. I feel Ford should reimburse me for my payments or give me another car of equal value or make up the difference I will lose if I take the car back. I also think they should provide me a loaner while my car is being fixed. Thank You [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11488988
48,000 miles · Sep 1, 2022
Unknown Or Other
The contact owns a 2020 Ford Escape. The contact stated that upon opening the front driver's side door, the track arm of the door failed to catch, causing the contact to hold the door by the door handle. The contact stated that the failure had been reoccurring. The dealer was notified of the failure and informed the contact that…
Read full complaint
The contact owns a 2020 Ford Escape. The contact stated that upon opening the front driver's side door, the track arm of the door failed to catch, causing the contact to hold the door by the door handle. The contact stated that the failure had been reoccurring. The dealer was notified of the failure and informed the contact that the vehicle had to be repaired out-of-pocket as the vehicle was out of warranty. The contact referenced Ford Technical Service Bulletin Number: 10184651. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline. The failure mileage was approximately 48,000.
NHTSA ODI #11482500
Mileage unknown · Aug 28, 2022
Electrical SystemLane DepartureUnknown Or Other
Windows operating intermittently. Repeatedly the dashboard flashes "Cross Traffic System Fault", "Blind Spot System Fault", "Blind Spot Left/Right Sensor Fault" occasionally "Cannot Access Memory While Driving". The lower center display panel on the instrument panel goes completely BLACK, and one cannot operate the defroster or…
Read full complaint
Windows operating intermittently. Repeatedly the dashboard flashes "Cross Traffic System Fault", "Blind Spot System Fault", "Blind Spot Left/Right Sensor Fault" occasionally "Cannot Access Memory While Driving". The lower center display panel on the instrument panel goes completely BLACK, and one cannot operate the defroster or air conditioner. The problem occurs intermittently, but when it starts it is more or less continuous for long periods of time. Ford (DeMontrond Ford) has now worked on the problem at least seven times, but safety issues do not stay fixed. Date below is when most recent series of issues occurred.
NHTSA ODI #11481625
Mileage unknown · May 23, 2022
Back Over PreventionLane DepartureUnknown Or Other
Repeatedly the dashboard flashes "Cross Traffic System Fault", "Blind Spot System Fault", "Blind Spot Left/Right Sensor Fault" occasionally "Cannot Access Memory While Driving". The lower center display panel on the instrument panel goes completely BLACK. The problem occurs intermittently, but when it starts it is more or less…
Read full complaint
Repeatedly the dashboard flashes "Cross Traffic System Fault", "Blind Spot System Fault", "Blind Spot Left/Right Sensor Fault" occasionally "Cannot Access Memory While Driving". The lower center display panel on the instrument panel goes completely BLACK. The problem occurs intermittently, but when it starts it is more or less continuous for long periods of time. Ford (DeMontrond Ford) has now worked on the problem at least six times.
NHTSA ODI #11465685
NHTSA investigations
2PE23013 · Failed Door Check Arm Attachment Point
Opened Jul 7, 2023 · Closed Jan 24, 2024
Status: closed (inferred from source dates) · Structure:body:door ; Structure:body:door:hinge And Attachments
On July 7, 2023, the Office of Defects Investigation (ODI) opened PE23-013 to investigate instances of check arm bracket failure in the front doors in model year (MY) 2020-2021 Ford Escape vehicles. At the time of opening, ODI received 118 Vehicle Owner Questionnaires (VOQs) alleging this failure. To date, ODI has received 593 VOQs alleging this failure, with a variety of reported failure conditions. The most common reported failure condition was reduced door functionality (e.g. door was more difficult to open or close) and the least common was inadvertent door opening. Other reported failure conditions include inability to latch and inability to open. Three VOQs reported injuries, one of which requiring medical attention. ODI conducted a consumer survey which yielded an additional 44 injuries (although the VOQs did not indicate any injury), none of which requiring medical attention. All these injuries were bumps/bruises from the door closing on occupants’ arms and legs while entering and exiting the vehicle. The function of the check arm system is to provide hold-open assist at specific angles and to assist with door closing energy. It does not provide vertical support of the door and is independent of the latching mechanism. This failure is progressive and detectable by vehicle occupants. Consumers commonly report hearing a popping or snapping noise when opening and closing the door. This noise is caused by some of the welds between the bracket and door structure failing and detaching. There may also be visible damage present to the welds in the door structure. Continued use of the door may result in all welds separating and the bracket fully detaching from the door structure, which could lead to increased resistance in closing and opening the door, restrained window operation, and the door freely rotating when open. ODI inspected 3 consumer vehicles in the field, and 2 test vehicles at Ford’s testing facility. The test vehicles were retrofitted with the failed component. ODI observed an increased door closing resistance, however, was unable to reproduce an inadvertent open while parked or driving, or a failure to latch or open condition. Testing also verified this failure did not affect the door ajar warning system. This system provides an audible and visual warning in the event a door did not achieve primary latch position. Ford has provided details on a one-time-repair customer satisfaction program (23B56), stating that they will provide customers with a letter, currently targeted for March 2024, to bring their vehicle to a Ford dealership for a proactive repair. Dealers will inspect the door check arm welds for damage and will either provide a rivet plate to reinforce the existing door check arm or will provide a replacement door, depending on the level of damage present. Customers will be eligible for reimbursement if they previously paid to repair this issue. In view of the high detectability of failure, low potential hazard to drivers, and Ford’s customer satisfaction program to provide a proactive repair, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Structure:body:door
On July 7, 2023, the Office of Defects Investigation (ODI) opened PE23-013 to investigate instances of check arm bracket failure in the front doors in model year (MY) 2020-2021 Ford Escape vehicles. At the time of opening, ODI received 118 Vehicle Owner Questionnaires (VOQs) alleging this failure. To date, ODI has received 593 VOQs alleging this failure, with a variety of reported failure conditions. The most common reported failure condition was reduced door functionality (e.g. door was more difficult to open or close) and the least common was inadvertent door opening. Other reported failure conditions include inability to latch and inability to open. Three VOQs reported injuries, one of which requiring medical attention. ODI conducted a consumer survey which yielded an additional 44 injuries (although the VOQs did not indicate any injury), none of which requiring medical attention. All these injuries were bumps/bruises from the door closing on occupants’ arms and legs while entering and exiting the vehicle. The function of the check arm system is to provide hold-open assist at specific angles and to assist with door closing energy. It does not provide vertical support of the door and is independent of the latching mechanism. This failure is progressive and detectable by vehicle occupants. Consumers commonly report hearing a popping or snapping noise when opening and closing the door. This noise is caused by some of the welds between the bracket and door structure failing and detaching. There may also be visible damage present to the welds in the door structure. Continued use of the door may result in all welds separating and the bracket fully detaching from the door structure, which could lead to increased resistance in closing and opening the door, restrained window operation, and the door freely rotating when open. ODI inspected 3 consumer vehicles in the field, and 2 test vehicles at Ford’s testing facility. The test vehicles were retrofitted with the failed component. ODI observed an increased door closing resistance, however, was unable to reproduce an inadvertent open while parked or driving, or a failure to latch or open condition. Testing also verified this failure did not affect the door ajar warning system. This system provides an audible and visual warning in the event a door did not achieve primary latch position. Ford has provided details on a one-time-repair customer satisfaction program (23B56), stating that they will provide customers with a letter, currently targeted for March 2024, to bring their vehicle to a Ford dealership for a proactive repair. Dealers will inspect the door check arm welds for damage and will either provide a rivet plate to reinforce the existing door check arm or will provide a replacement door, depending on the level of damage present. Customers will be eligible for reimbursement if they previously paid to repair this issue. In view of the high detectability of failure, low potential hazard to drivers, and Ford’s customer satisfaction program to provide a proactive repair, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Structure:body:door:hinge And Attachments
On July 7, 2023, the Office of Defects Investigation (ODI) opened PE23-013 to investigate instances of check arm bracket failure in the front doors in model year (MY) 2020-2021 Ford Escape vehicles. At the time of opening, ODI received 118 Vehicle Owner Questionnaires (VOQs) alleging this failure. To date, ODI has received 593 VOQs alleging this failure, with a variety of reported failure conditions. The most common reported failure condition was reduced door functionality (e.g. door was more difficult to open or close) and the least common was inadvertent door opening. Other reported failure conditions include inability to latch and inability to open. Three VOQs reported injuries, one of which requiring medical attention. ODI conducted a consumer survey which yielded an additional 44 injuries (although the VOQs did not indicate any injury), none of which requiring medical attention. All these injuries were bumps/bruises from the door closing on occupants’ arms and legs while entering and exiting the vehicle. The function of the check arm system is to provide hold-open assist at specific angles and to assist with door closing energy. It does not provide vertical support of the door and is independent of the latching mechanism. This failure is progressive and detectable by vehicle occupants. Consumers commonly report hearing a popping or snapping noise when opening and closing the door. This noise is caused by some of the welds between the bracket and door structure failing and detaching. There may also be visible damage present to the welds in the door structure. Continued use of the door may result in all welds separating and the bracket fully detaching from the door structure, which could lead to increased resistance in closing and opening the door, restrained window operation, and the door freely rotating when open. ODI inspected 3 consumer vehicles in the field, and 2 test vehicles at Ford’s testing facility. The test vehicles were retrofitted with the failed component. ODI observed an increased door closing resistance, however, was unable to reproduce an inadvertent open while parked or driving, or a failure to latch or open condition. Testing also verified this failure did not affect the door ajar warning system. This system provides an audible and visual warning in the event a door did not achieve primary latch position. Ford has provided details on a one-time-repair customer satisfaction program (23B56), stating that they will provide customers with a letter, currently targeted for March 2024, to bring their vehicle to a Ford dealership for a proactive repair. Dealers will inspect the door check arm welds for damage and will either provide a rivet plate to reinforce the existing door check arm or will provide a replacement door, depending on the level of damage present. Customers will be eligible for reimbursement if they previously paid to repair this issue. In view of the high detectability of failure, low potential hazard to drivers, and Ford’s customer satisfaction program to provide a proactive repair, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration