Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
What owners actually said
2,444 reports
Mileage unknown · Sep 20, 2025
EngineSteering
Since the day I bought my 2013 Edge I have had nothing but problems ranging from Backup Camera always has a distorted image, appears upside down or it will just be blank. For the last year I have had my car looked at, changed everything that could possibly be changed to now my car can be going down the road running 55-60 MPH and…
Read full complaint
Since the day I bought my 2013 Edge I have had nothing but problems ranging from Backup Camera always has a distorted image, appears upside down or it will just be blank. For the last year I have had my car looked at, changed everything that could possibly be changed to now my car can be going down the road running 55-60 MPH and the car will just shut down and flash random warnings on the dash but the scariest & most unsafe part is how the steering wheel locks up or I lose power steering making it hard to move or coast off the road to safety. At this point I don't know what else to do. Questions below are asking for dates but unfortunately there are so many dates that my car does this as it happens almost daily so I will put date for the last day I drove it. Right now it has been sitting at a mechanic's place for the last 3.5 weeks.
NHTSA ODI #11688651
Mileage unknown · Sep 13, 2025
Back Over PreventionUnknown Or Other
The backup camera stopped working consistently in June 2025. Safety recall has been issued for 2015 vehicles and newer, but not for 2013 and 2014 years. Ford dealer said the camera needs to be replaced for $740, but numerous online comments show other Ford owners with the same issue starting at the same time. I believe this is a…
Read full complaint
The backup camera stopped working consistently in June 2025. Safety recall has been issued for 2015 vehicles and newer, but not for 2013 and 2014 years. Ford dealer said the camera needs to be replaced for $740, but numerous online comments show other Ford owners with the same issue starting at the same time. I believe this is a software issue, and would like 2013 Ford Edge to be added to safety recall.
NHTSA ODI #11687037
Mileage unknown · Sep 11, 2025
Unknown Or Other
The back up camera shows an inverted image. This has been happening for the past year. This is similar to the recall for 2015-19 Ford Edges, however we are have a 2013.
NHTSA ODI #11686694
Mileage unknown · Sep 11, 2025
Unknown Or Other
The rearview camera has not been working correctly for now over 8 years or more. The rearview camera issue causes a blank or distorted image on the center display. It is now displaying the image upside down as well. There are currently other Ford vehicle vehicles that are being recalled for this issue. I wanna know why our vehic…
Read full complaint
The rearview camera has not been working correctly for now over 8 years or more. The rearview camera issue causes a blank or distorted image on the center display. It is now displaying the image upside down as well. There are currently other Ford vehicle vehicles that are being recalled for this issue. I wanna know why our vehicle is not included in this. It is a 2013 Ford edge which I have talked to other people that own the same year have the same issues. This is very upsetting because this is an issue with other vehicles that are not included in those recalls.
NHTSA ODI #11686647
Mileage unknown · Sep 11, 2025
Electrical System
The rear back up camera intermittantly fails on this vehicle. About 70% of the time, it displays a black screen. The screen will display "Contact Dealership." This has been occurring for approx. 1 year.
NHTSA ODI #11686497
Mileage unknown · Sep 10, 2025
Unknown Or Other
There is currently a recall on back up cameras for ford edges 2015-2019, the cameras are upside down, blacking out, lots of issues. My edge is a 2013 and I am having the same issue. I am unable to use the camera as it’s upside down and when it’s not upside down, it’s flashing off and on. It’s hazardous and this should fall under…
Read full complaint
There is currently a recall on back up cameras for ford edges 2015-2019, the cameras are upside down, blacking out, lots of issues. My edge is a 2013 and I am having the same issue. I am unable to use the camera as it’s upside down and when it’s not upside down, it’s flashing off and on. It’s hazardous and this should fall under the recall as well. I was told since I have a 2013, it does not fall under the recall. Which it should.
NHTSA ODI #11686456
60,953 miles · Sep 9, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while attempting to reverse, the back over prevention camera malfunction and failed to display an image. There was no warning light illuminated. The vehicle was taken to a local auto body shop where it was diagnosed, and the contact was informed that the camera was fault…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while attempting to reverse, the back over prevention camera malfunction and failed to display an image. There was no warning light illuminated. The vehicle was taken to a local auto body shop where it was diagnosed, and the contact was informed that the camera was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 60,953.
NHTSA ODI #11686123
Mileage unknown · Sep 9, 2025
Electrical SystemUnknown Or Other
It is my rear view camera. I would put the vehicle in reverse and it will sometimes start to work and than it will shut off and a message comes across saying I need to contact dealership. It will sometimes come up and be upside down or I will put the vehicle in reverse and the back up camera just flashes while in use. I have no…
Read full complaint
It is my rear view camera. I would put the vehicle in reverse and it will sometimes start to work and than it will shut off and a message comes across saying I need to contact dealership. It will sometimes come up and be upside down or I will put the vehicle in reverse and the back up camera just flashes while in use. I have not taken the vehicle to the shop. I have called and they said it sounds electrical. But the recall you just released on 2015 Ford edges for the back up camera is the same thing that is going on with my vehicle and I have a 2013.
NHTSA ODI #11685927
Mileage unknown · Sep 5, 2025
Engine
Water pump failure coolant leaking out of it Was driving at 10mph in parking garage when temperature gauge went to hot on cluster instrument everyone was ok had have had vehicle for about a month before breakdown private dealer did say there were no issues car has not been checked by a certified dealership.
NHTSA ODI #11685279
110,000 miles · Sep 2, 2025
Service Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 40 MPH, the brake pedal was depressed too slowly for traffic; however, the brake pedal was soft and went to the floorboard. The vehicle was steered to the right and rolled down into a ditch to avoid crashing into the vehicle in front. The cont…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 40 MPH, the brake pedal was depressed too slowly for traffic; however, the brake pedal was soft and went to the floorboard. The vehicle was steered to the right and rolled down into a ditch to avoid crashing into the vehicle in front. The contact stated that the engine was still running. There was no warning light illuminated. The vehicle was turned off and restarted to reset the braking system; however, the brake pedal was still soft. There was no damage to the vehicle, and the contact was able to drive out of the ditch and back to the residence. The vehicle was not yet taken to a local dealer or independent mechanic to be diagnosed or repaired. The contact stated that in 2024, the vehicle was repaired under Customer Satisfaction Program: 13N02 - Brake Booster (Service Brakes, Hydraulic). The manufacturer was informed of the failure. The failure mileage was approximately 110,000.
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
2013 Ford Edge Problems, Complaints & Recalls | Skip That Year
Illustration