← New search

2013 Ford Edge

Owner reports · Recalls · Investigations

More warning signs than most Edge years

Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.

About this comparison →

When problems were reported

Mileage at the reported incident

1,793 reports with mileage · 651 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

33 crash reports7 fire reports24 injury reports

What owners actually said

2,444 reports
Mileage unknown · Mar 19, 2026
Unknown Or Other

Starting about a year and a half ago, my backup camera would either say “camera is unavailable, contact dealership” or be upside down or some sort of distorted image. Sometimes the camera works. It poses a risk to me and others.sometimes the camera will cut out and go black after I have started backing up with it. No other warn…

Read full complaint

Starting about a year and a half ago, my backup camera would either say “camera is unavailable, contact dealership” or be upside down or some sort of distorted image. Sometimes the camera works. It poses a risk to me and others.sometimes the camera will cut out and go black after I have started backing up with it. No other warning lights have come on. Other ford edges have been recalled for the same issue but not the 2013.

NHTSA ODI #11725519

Mileage unknown · Mar 13, 2026
Service Brakes

Breaks went out on car.started out only when I hit a bump I’d loose them… turn car off and pump them back… now they are just gone! Replaced pads rotors calipers, now changing master cylinder.. from what I’ve read that won’t help but have to try! They should really put a recall out for this!

NHTSA ODI #11724021

141,000 miles · Mar 9, 2026
Back Over Prevention

The contact owns a 2013 Ford Edge. The contact stated that while reversing, the camera was inoperable. The contact referenced NHTSA Campaign Number: 25V572000 (BACK OVER PREVENTION); however, the VIN was not included in the recall. The vehicle was driven to a dealer. The vehicle was repaired. The manufacturer was not notified of…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while reversing, the camera was inoperable. The contact referenced NHTSA Campaign Number: 25V572000 (BACK OVER PREVENTION); however, the VIN was not included in the recall. The vehicle was driven to a dealer. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 141,000.

NHTSA ODI #11723138

Mileage unknown · Mar 7, 2026
Unknown Or Other

My backup camera continues to not work sometimes it shows upside down or black screen and says I need to contact the dealership. When I contact the place that I got it from it says it's not covered under their warranty in the contact Ford. When I contact Ford they said there was some rear backup camera thing going on and that th…

Read full complaint

My backup camera continues to not work sometimes it shows upside down or black screen and says I need to contact the dealership. When I contact the place that I got it from it says it's not covered under their warranty in the contact Ford. When I contact Ford they said there was some rear backup camera thing going on and that the recall had not been issued yet?

NHTSA ODI #11722658

Mileage unknown · Mar 6, 2026
EngineExterior LightingFuel/propulsion System

I have several different things going on. First of all my rear turn signals do not work, nor do my rear hazard lights. I've taken it to a mechanic who has extensively looked at this and has determined that it's the body control modular and is suggested replacement. I have been waiting for several months for this part to come in …

Read full complaint

I have several different things going on. First of all my rear turn signals do not work, nor do my rear hazard lights. I've taken it to a mechanic who has extensively looked at this and has determined that it's the body control modular and is suggested replacement. I have been waiting for several months for this part to come in but he keeps telling me it's on back order. Also, my radiator fan/assembly went bad and had to be replaced. Upon the mechanic installing the new fan assembly, I had numerous fuses blown and that is when my blinker and hazard light issue started. This is a major safety concern as signaling the direction that you're turning is very important to other drivers. Additionally, it is against the law not to use signals. I'm constantly in fear that someone is going to rear in me because of my inability to signal when switching lanes and or turning. Additionally, my back up camera stopped working shows a black screen with a notice to contact the dealer. Another issue I have is that my door ajar light is illuminated all the time. I often feel unsafe and fear that the door may just come open at any time, I am unable to lock my doors with the internal lock , which means my doors are left unlocked while I'm in the vehicle. Also, the interior lights stay on for awhile when car turned off, thus putting more strain on the battery, which I've just replaced. Plus, the dome light will not go off until you accelerated to about 20 mph, however, when putting the car in reverse there's no way to get the lights to turn off in this causes visibility issues at night. That in conjunction with my backup camera not working makes it a very dangerous situation when going in reverse. I also detect the odor of gasoline which lingers in my vehicle for some time after getting fuel. I'm scared that there's a leak and if so the potential of a fire is very concerning. And I've noticed that my gas mileage is not really good and I'm not sure if that's related.

NHTSA ODI #11722586

Mileage unknown · Feb 28, 2026
Air BagsCrashInjury

The airbags did not deploy when the car was in a front and rear end collision on 2/12/26. Injuries occurred. No one has confirmed the problem. The car was taken to a Collison center to be evaluated but am uncertain if that part has been evaluated. There were not symptoms of failure beforehand.

NHTSA ODI #11721104

Mileage unknown · Feb 7, 2026
Service Brakes

The brake booster went out first, replaced the brake booster and master cylinder, 2 calipers, brake pads, and rotors. The next option was to replace the brake lines. The problem was not solved; the calipers still locked up.

NHTSA ODI #11716415

Mileage unknown · Jan 21, 2026
Service Brakes

I have a 2013 FORD Edge that the ABS module has gone out deeming the vehicle unsafe to drive. We have spoken to several FORD dealership team members and have all stated that the part should be recalled and the part is unavailable until sometime next year or later. We were told by FORD customer service, that in order to escalate …

Read full complaint

I have a 2013 FORD Edge that the ABS module has gone out deeming the vehicle unsafe to drive. We have spoken to several FORD dealership team members and have all stated that the part should be recalled and the part is unavailable until sometime next year or later. We were told by FORD customer service, that in order to escalate the issue, then we needed to take to a dealership. We dropped the car off and never heard back from anyone and finally after many attempts to contact the dealership, I was finally able to get a team member on the line. They then tell us until we pay the diagnostic fees, they can't do anything. We were never told that from the start of the initial call and are back to square one. The car has no anti-lock brakes and is deemed unsafe to drive, please assist in anyway possible.

NHTSA ODI #11712517

Mileage unknown · Jan 19, 2026
Service Brakes

The ABS Control Module failed in my 2013 Ford Edge. I no longer have anti-lock brakes and my wife does not feel safe driving the car. I talked to a number of different Ford Dealerships and every service technician I talked to told me they don't know how this issue is not a recall as it is happening so often that the part is ba…

Read full complaint

The ABS Control Module failed in my 2013 Ford Edge. I no longer have anti-lock brakes and my wife does not feel safe driving the car. I talked to a number of different Ford Dealerships and every service technician I talked to told me they don't know how this issue is not a recall as it is happening so often that the part is back ordered by a year. I had the problem confirmed by in independent service center and was informed to bring to a Ford Dealership. The vehicle is now at a Ford Dealership awaiting diagnosis but they all said they know what the problem is and they can't get the part. There are multiple warning lamps going off when you start the vehicle. ABS warning lamp, service advancetrac lights and brake warning lamps. This issue just popped up and we brought to an independent service center to get fixed and they were aware of this issue and told me that you can't get the part and to contact Ford. They also told us that if you push the brakes too hard it could cause them to lock up which is a huge safety concern and now my wife will not drive the vehicle and I can not sell it to anyone like that so we are stuck. Please help.

NHTSA ODI #11711907

Mileage unknown · Jan 15, 2026
Forward Collision AvoidanceService Brakes

This is on a 2013 Ford Edge with Adaptive Cruise Control. The brakes failed and went completely to the floor, putting the driver/passengers at danger along with other vehicles in the vicinity. The ABS control module with HCU is the part that failed. Ford part # CT4Z-2C405-A. Per the dealership and per Ford, this part is now …

Read full complaint

This is on a 2013 Ford Edge with Adaptive Cruise Control. The brakes failed and went completely to the floor, putting the driver/passengers at danger along with other vehicles in the vicinity. The ABS control module with HCU is the part that failed. Ford part # CT4Z-2C405-A. Per the dealership and per Ford, this part is now obsolete and unavailable, which means the vehicle is currently unsafe to drive and unusable. Ford does not have any plan at the moment to correct this issue.

NHTSA ODI #11711271

Official recalls

2

14V393000 · Power Train:axle Assembly:axle Shaft

Jul 2, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.

Consequence & remedy

Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.

Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.

14V002000 · Fuel System, Gasoline

Jan 6, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.

Consequence & remedy

Consequence: A fuel leak in the presence of an ignition source may result in a fire.

Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

PE16012 · Door Ajar Warning Light Always On

Opened Sep 28, 2016 · Closed Mar 20, 2017

Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Additional source detail variants (3)

Interior Lighting

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.