NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
2,444 reports94,000 miles · Jan 4, 2023
Service Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated that while operating the vehicle, the braking system malfunctioned causing the brake pedal to become soft, hard, or extend to the floorboard while depressed, causing the braking distance to become extended. The vehicle was taken to the local mechanic who diagnosed that the br…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while operating the vehicle, the braking system malfunctioned causing the brake pedal to become soft, hard, or extend to the floorboard while depressed, causing the braking distance to become extended. The vehicle was taken to the local mechanic who diagnosed that the brake booster was faulty and needed to be replaced. The vehicle was not yet repaired. The local dealer was notified of the failure, but no assistance was offered. The contact was informed that the Extended Warranty coverage related to the failure had expired. The failure mileage was 94,000.
NHTSA ODI #11500172
Mileage unknown · Jan 4, 2023
Electrical SystemExterior LightingService Brakes
Due to the door latch issue and my interior light staying on I am unable to see at night when driving. It has caused issues with my battery and I have had to replace it a few times. Why isn't Ford recalling this?
NHTSA ODI #11500057
60,000 miles · Dec 14, 2022
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that on various occasions while reversing, the rearview camera intermittently failed to display. The contact then stated that the failure recurred while reversing and the rearview image was distorted and then a "Camera Unavailable, Please Contact Your Dealer" message was disp…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that on various occasions while reversing, the rearview camera intermittently failed to display. The contact then stated that the failure recurred while reversing and the rearview image was distorted and then a "Camera Unavailable, Please Contact Your Dealer" message was displayed. The vehicle was taken to an independent mechanic, who made the contact aware of a rearview camera extended warranty; however, the VIN was not included, and the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and informed the contact that the VIN was not included in a rearview camera class action lawsuit, and advised her to file a complaint with the NHTSA hotline. The approximate failure mileage was 60,000.
NHTSA ODI #11497460
Mileage unknown · Dec 13, 2022
Service Brakes
In July 2022, brakes gave out twice, pedal going all the way to the floor; hard to stop. Then it mysteriously went away. Happened again in November 2022. Found out Ford issued an extended warranty (13N02) on a faulty brake booster. Took it to Galpin Ford. They replaced the booster under this warranty. Yesterday, 12/12/22, we had…
Read full complaint
In July 2022, brakes gave out twice, pedal going all the way to the floor; hard to stop. Then it mysteriously went away. Happened again in November 2022. Found out Ford issued an extended warranty (13N02) on a faulty brake booster. Took it to Galpin Ford. They replaced the booster under this warranty. Yesterday, 12/12/22, we had a bit of snow, wife drove the car, almost crashed as brake failure yet again! Took it back to Galping Ford who says 'they cannot find anything wrong'. That's BS! This Edge has less than 70,000 miles and is driven by a middle age female (not being aggressively driven). We bought this vehicle used from Galpin Ford and they DID NOT inform us of this problem. Now we have a dangerous car to drive; I can't sell it or I'm liable! There is NO recourse for us owners and we are paying the price (both financially and with our lives) because NHSTA has failed to issue a recall. Get these cars fixed or off the road! Owners should not have to bear this financial burden.
NHTSA ODI #11497209
Mileage unknown · Dec 11, 2022
Service Brakes
When braking the brakes go all the way down to the floor and I do not stop immediately. I was driving home from work Fri 12/9 after dark and had to swerve to keep from hitting an animal in the road because my brakes did not brake as I expected. If was very unnerving.
NHTSA ODI #11496973
Mileage unknown · Dec 3, 2022
Latches/locks/linkagesUnknown Or Other
My issue is that there is a door ajar alarm that I brought my vehicle into the dealer to fix. With this alarm you are unable to lock your doors while inside the vehicle. Someone tried to steal our vehicle from us with us inside, just walked up and opened the door. The attempt was unsuccessful and we got away but it had me thinki…
Read full complaint
My issue is that there is a door ajar alarm that I brought my vehicle into the dealer to fix. With this alarm you are unable to lock your doors while inside the vehicle. Someone tried to steal our vehicle from us with us inside, just walked up and opened the door. The attempt was unsuccessful and we got away but it had me thinking that if we had small children in our vehicle, they could easily open the door and fall out. The dealer said this is a known issue and it would cost over $500 to fix but recommended NOT fixing it because it would just happen again, it's a bad part/design they said. I did call Ford Motor Company and they advised me to report this to you so I'm reporting this before someone gets killed from this known issue.
NHTSA ODI #11495912
Mileage unknown · Dec 1, 2022
Forward Collision AvoidanceService Brakes
9/15/2022 paid $875.90 for brake booster, two weeks later, ABS module going out, according to Moyer Ford, as of 12/01/2022, I’ve called Ford Complaint and they fail to add my vin number, says only nhtsa can do that. As of today, 12/01/2022, Moyer ford is telling me abs modules are on back order with no ETA. Ford knows this is ma…
Read full complaint
9/15/2022 paid $875.90 for brake booster, two weeks later, ABS module going out, according to Moyer Ford, as of 12/01/2022, I’ve called Ford Complaint and they fail to add my vin number, says only nhtsa can do that. As of today, 12/01/2022, Moyer ford is telling me abs modules are on back order with no ETA. Ford knows this is major brake issue but not addressing it! Now when abs part does come in, that’s another $800 out of my pocket, total of $1700 that Ford is ignoring and don’t even have the parts to fix! Major concern!
NHTSA ODI #11495637
Mileage unknown · Nov 30, 2022
Service Brakes
While driving my 2013 Ford Edge Sport down the highway at 60mph the traffic light changed to yellow and then red as normal. When I went to apply the brakes the brake pedal suddenly lost pressure and went to the floor before the vehicle was able to stop. By this time I was in the middle of the intersection. By some miracle I was …
Read full complaint
While driving my 2013 Ford Edge Sport down the highway at 60mph the traffic light changed to yellow and then red as normal. When I went to apply the brakes the brake pedal suddenly lost pressure and went to the floor before the vehicle was able to stop. By this time I was in the middle of the intersection. By some miracle I was able to avoid a potentially serious accident as luckily no cars were in the intersection. The brakes were fine one moment and then no brakes the next with no warning lights or error codes. The brakes haven’t changed since then. Still no pressure and I’m afraid the drive the vehicle. My vehicle has yet to be inspected/diagnosed, but after doing extensive research online I’ve found that this is a very common problem with the ABS system. Apparently the valves get stuck open allowing fluid to flow freely past them and the system needs replaced. How is this not a safety issue. I’ve read that so many people have almost been in serious accidents were death could potentially occur. I don’t understand why this has not been recalled. The brake fluid is at normal level and the brake booster was previously replaced by Ford a couple years ago. In that instance the brake pedal was very hard and the vehicle would not respond to braking. That issue was fixed by Ford on their dime and I was told it was some secret or unpublished recall on certain vehicles, depending on where they were manufactured. This is gross negligence on Fords part and can’t wait for someone to sue the pants off them.
NHTSA ODI #11495557
Mileage unknown · Nov 28, 2022
EngineService Brakes
including hard or stiff power brakes that are difficult to press down and increased stopping distance. This may be due to a failing vacuum pump or hydraulic pressure pump. You may also find that your brake pedal is positioned higher than usual. As a result, you may have to lift your foot higher to press on the brake pedal, ap…
Read full complaint
including hard or stiff power brakes that are difficult to press down and increased stopping distance. This may be due to a failing vacuum pump or hydraulic pressure pump. You may also find that your brake pedal is positioned higher than usual. As a result, you may have to lift your foot higher to press on the brake pedal, apply more force, or
NHTSA ODI #11495118
30,000 miles · Nov 21, 2022
Service Brakes
The contact owns a 2013 Ford Edge. The contact stated that while reversing out of the garage, she depressed the brake pedal and the vehicle failed to respond. The contact stated that she had to apply extra pressure to the brake pedal to stop the vehicle. No warning lights were illuminated. The contact stated that she previously …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing out of the garage, she depressed the brake pedal and the vehicle failed to respond. The contact stated that she had to apply extra pressure to the brake pedal to stop the vehicle. No warning lights were illuminated. The contact stated that she previously had the vehicle diagnosed but the failure could not be determined. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 30,000.
NHTSA ODI #11494479
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration