IllustrationThe back up camera is inoperable at times. Rarely works on hot days or anytime the rear of the EDGE is facing the Sun. It hasn't worked properly for years. I'm not sure of the exact date or mileage it first happened, but it definitely started acting up around 2019.
2013 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
What owners actually said
2,444 reportsThe contact owns a 2013 Ford Edge. The contact stated that while driving at various speeds and attempting to decelerate or come to a complete stop, there was an abnormal sound while depressing the brake pedal. The brake warning light was illuminated. In addition, the contact stated that while in reverse, the rear-view camera dis…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving at various speeds and attempting to decelerate or come to a complete stop, there was an abnormal sound while depressing the brake pedal. The brake warning light was illuminated. In addition, the contact stated that while in reverse, the rear-view camera displayed an upside-down image. The vehicle was taken to a local dealer where it was diagnosed and determined that the power booster brake hose needed to be replaced. The vehicle was not repaired. Upon further investigation, the contact associated the failure with an unknown recall; however, the VIN was not under recall. The manufacturer was made aware of the failure, and a case was filed. The failure mileage was approximately 100,000.
The car did not brake randomly back in may when I was picking my toddler up from school. I contacted Ford dealership and they said braking issues is a known issue with the edge but my vehicle has no recalls. I could pay almost $300 for a diagnostic fee but nothing would be covered because their was a recall for the brake booster…
Read full complaint
The car did not brake randomly back in may when I was picking my toddler up from school. I contacted Ford dealership and they said braking issues is a known issue with the edge but my vehicle has no recalls. I could pay almost $300 for a diagnostic fee but nothing would be covered because their was a recall for the brake booster but that was back in 2013-2014. So I went to brakes plus, first they replaced the master cylinder then they replaced the brake booster a week later. Here I am 3 months later and the same issue.The vehicle randomly did not brake AGAIN. Got the vehicle back to brakes plus to have the vehicle looked at again. They replaced the brake booster under warranty then reached out to Ford who let them know the brake booster and brake lines are a know defect with the vehicle and I can have my vehicle looked at by them but I would need to pay the fee and nothing would be covered . How is this a known issue and nothing is covered? Ford checked my Vin and no vehicle recall. I reached out to Ford corporate and they created a case number: Cxh-09196123-F6m4z3 I am pregnant and I feel this car is dangerous if this is a known issue.
Just purchased this used vehicle from Orange Auto Connection in [XXX] on XXX. Car was in perfect operating condition. 2 days later while driving with my 2 granddaughters I was approaching a stop sign at about 35-40 mph and as I started to push on the break pedal it became very soft and pushed all the way to the floor with no res…
Read full complaint
Just purchased this used vehicle from Orange Auto Connection in [XXX] on XXX. Car was in perfect operating condition. 2 days later while driving with my 2 granddaughters I was approaching a stop sign at about 35-40 mph and as I started to push on the break pedal it became very soft and pushed all the way to the floor with no resistance. I thought the car wouldnt stop,. Thankfully it did without an accident . It has not returned to the normal breaking conditions. Today is XXX. I have to drive this car everyday as it is my only vehicle. I didn't buy an extended warranty from the dealer because I couldn't afford it. Why has this issue not become a safety recall. If I had known about this problem that has apparently been addressed years ago and had just expired in November 2025 prior to buying this car I wouldn't have purchased it. They are a lot of people including myself that live check to check and still struggle with every day necessities and potentially being faced with a heafty repair bill to fix a dangerous fault that manufacture knew about really causes sleepless nights and undo stress that they should not have to endure because they are afraid they will be hurt or hurt othera in an accident caused by a manufacture defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
While driving on the highway at 70 mph, the driver's side front halfshaft completely detached from the vehicle, causing an immediate loss of drive power and creating a severe crash hazard."
The backup camera will flip upside down or go completely blank or not work at all. I had my car in reverse and the camera didn’t come on and one time I flipped upside down and now it don’t work at all.
The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 30 MPH, the brake pedal was inoperative. The contact stated that the vehicle drove for several yards, and the contact was unable to reach the parking brake. The vehicle was shifted into park(P) to attempt to stop the vehicle. The contact state…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 30 MPH, the brake pedal was inoperative. The contact stated that the vehicle drove for several yards, and the contact was unable to reach the parking brake. The vehicle was shifted into park(P) to attempt to stop the vehicle. The contact stated that the vehicle crashed into the shrubs in front of the window at an independent mechanic shop, causing the vehicle to come to a stop right before almost crashing into the shop window, which resulted in minor damage to the front bumper. No warning lights were illuminated. The air bags were not deployed. An independent mechanic diagnosed the vehicle and stated that the brake pads and rotors needed to be replaced. The vehicle was repaired; however, the failure persisted. The vehicle was taken to another independent mechanic, where it was diagnosed and determined that the brake booster module needed to be replaced. The vehicle was repaired; however, the failure persisted. The contact researched and was made aware of an unknown recall; however, the VIN was not included. The failure had occurred on several occasions. There were no injuries sustained. A Police report was not filed. The manufacturer was notified of the failure. The failure mileage was approximately 78,000.
When I put my 2013 Ford edge in reverse the backup camera goes out for about 5 to 10 seconds or it just doesn’t work at all. And also I just paid $672 to have the drivers side door latch replaced because the recall had expired in November of 2025 the door ajar light would stay on and the dash would say place vehicle in park
The Gas Cap is defected the light always comes on and you have to pump gas a certain way.
Frequently, when the car is in reverse, the screen which shows the image from the backup camera goes blank while backing up. The screen typically stays blank for approximately 5 seconds and then comes back on. Sometimes I have to place the shifter in “park” and then return to “reverse” to get the screen to display the image. I h…
Read full complaint
Frequently, when the car is in reverse, the screen which shows the image from the backup camera goes blank while backing up. The screen typically stays blank for approximately 5 seconds and then comes back on. Sometimes I have to place the shifter in “park” and then return to “reverse” to get the screen to display the image. I have received a letter from Ford Motor Co. which describes the stated condition and offering to repair free of charge for vehicles that are not older than 15 years. However, the letter references only my 2015 Ford F150. I called the local dealer to see if my 2013 Edge is covered under the recall and the dealer stated it is not covered. Since my Edge is less than 15 years old I think Ford should have to cover all Ford vehicles which have the stated problem.
Official recalls
214V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.