Brakes hiss are spongy and then get solid and hard to stop vehicle. Vehicle was made in Oakville plant where 2013 Ford Edge’s have been identified to have known issues with brake booster (Ford program 13N02) although they say my Ford does not qualify even with only 60k miles.
2013 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
529 reportsHissing sound when the brake pedal was depressed and then the stiffness in the pedal itself. There was little to extremely little braking power and was very difficult to slow and stop the vehicle. Took the car to a local repair shop and determined that it was a faulty brake booster. They felt that it should be taken to the de…
Read full complaint
Hissing sound when the brake pedal was depressed and then the stiffness in the pedal itself. There was little to extremely little braking power and was very difficult to slow and stop the vehicle. Took the car to a local repair shop and determined that it was a faulty brake booster. They felt that it should be taken to the dealer, which I did. I did find out that this is a very common problem with the same make and model Fords. A Customer Satisfaction program 13N02 was launched but not for my vin. This is a very dangerous situation feel that more investigation should be done on this particular product.
This is not an unknown problem to NHTSA or Ford for covered vehicles. Brake booster failed, causing serious problems with the ability to stop the vehicle. For other 2013 Ford Edge and Mercury MKX vehicles, this repair is covered (NHTSA 10054925), while some of these vehicles are not covered for some reason, including this VIN. …
Read full complaint
This is not an unknown problem to NHTSA or Ford for covered vehicles. Brake booster failed, causing serious problems with the ability to stop the vehicle. For other 2013 Ford Edge and Mercury MKX vehicles, this repair is covered (NHTSA 10054925), while some of these vehicles are not covered for some reason, including this VIN. The brake booster failure on this vehicle presents no less of a safety issue than that of the covered vehicles, which received a Ford 10 year extended warranty on the brake booster. No warning lamps, messages, or other symptoms.
This is a vigilant preventative report. There aren't any warning lamps, failures or messages yet and I sure am glad. But the symptoms were noticed on May 21, 2021 after I returned home from getting my emissions done. I noticed both front tires were streaming wet with liquid and at first I thought I had run over something. Then …
Read full complaint
This is a vigilant preventative report. There aren't any warning lamps, failures or messages yet and I sure am glad. But the symptoms were noticed on May 21, 2021 after I returned home from getting my emissions done. I noticed both front tires were streaming wet with liquid and at first I thought I had run over something. Then today May 30, I needed to run to the grocery store but before I left I had my son look underneath the hood because I thought maybe a fluid or freon may have caused the scene but soon found out that there is no way for any fluids to penetrate to the tires because there is a solid panel separating the mechanisms underneath the hood from the wheels and tire. That made me take a closer look at the inside of the wheel covers/caps and low and behold you can see because of the dark color of the fluid in the wells of the wheels; brake fluid has been spewing now, both times as far as I can tell. I don't know how long it takes for the fluid reservoir to become empty, but I sure wouldn't want to be driving my vehicle when that happens. So this is in my opinion a "Life or Death" Safety Hazard and would really be appreciative for an immediate response! I need your suggestion as soon as you're able to, what should be my next step. I am a senior citizen and I purchased this 2013 vehicle as my future retirement vehicle in 2014 and retired in 2017. I believed it would be a nice, sturdy well-built and reliable vehicle for years to come. I've owned many a vehicle and have never had any major brake issues during all those years, just regular maintenance on brakes and other expected low maintenance. Never anything of this magnitude to put my life in danger. Wow! An 8 year old vehicle with just under 73,000 miles on the odometer driven less that 50 miles per month, I wouldn't have ever thought this could happen. Hopefully, there is a Safety Recall for this model as well. Still researching....
I HAVE EXPERIENCED SEVERAL OCCASIONS WHERE I HAVE EITHER HAD TO 1) PRESS THE BRAKES VERY HARD TO THE FLOOR TO STOP, SOMETIMES STILL ROLLING OR 2) OCCASIONALLY FELT VERY STIFF BRAKES THAT WILL NOT STOP THE CAR WHEN PRESSING ON THE BRAKE. THE CAR WOULD CONTINUE TO ROLL. I HAD TO PULL TO THE SIDE SO I WOULD NOT IMPACT THE CAR IN F…
Read full complaint
I HAVE EXPERIENCED SEVERAL OCCASIONS WHERE I HAVE EITHER HAD TO 1) PRESS THE BRAKES VERY HARD TO THE FLOOR TO STOP, SOMETIMES STILL ROLLING OR 2) OCCASIONALLY FELT VERY STIFF BRAKES THAT WILL NOT STOP THE CAR WHEN PRESSING ON THE BRAKE. THE CAR WOULD CONTINUE TO ROLL. I HAD TO PULL TO THE SIDE SO I WOULD NOT IMPACT THE CAR IN FRONT OF ME. THIS HAS HAPPENED SEVERAL TIMES ON HIGHWAY 23. THERE WAS A RECALL FOR A BRAKE BOOSTER ISSUE, BUT FORD CLAIMS MY CAR WAS MADE THE MONTH AFTER THE RECALL ENDED. THIS ISSUE HAS BEEN HAPPENING FOR YEARS, AND GETTING WORSE RECENTLY. WE HAD TO SCHEDULE THE REPAIR BECAUSE THE CAR WAS UNSAFE TO DRIVE. THE BRAKES WERE IN GOOD CONDITION OTHERWISE - NO OTHER ISSUES.
ON GOING ISSUE WITH BRAKE BOOSTER FAILURE, JUST HAD THE 2ND BRAKE BOOSTER REPLACED FOR A HARD BRAKE PEDAL DUE TO DIAPHRAM FAILURE IN THE BOOSTER, IT WAS REPLACED AT A LOCAL FORD DEALERSHIP ON DAY OF 3/2/2018 MILAGE ON VEHICLE WAS 42785 (THIS BOOSTER WAS REPLACED UNDER AN EXTENDED PART WARRANTY DEFECT) 3RD NEW BOOSTER INSTALLED 3…
Read full complaint
ON GOING ISSUE WITH BRAKE BOOSTER FAILURE, JUST HAD THE 2ND BRAKE BOOSTER REPLACED FOR A HARD BRAKE PEDAL DUE TO DIAPHRAM FAILURE IN THE BOOSTER, IT WAS REPLACED AT A LOCAL FORD DEALERSHIP ON DAY OF 3/2/2018 MILAGE ON VEHICLE WAS 42785 (THIS BOOSTER WAS REPLACED UNDER AN EXTENDED PART WARRANTY DEFECT) 3RD NEW BOOSTER INSTALLED 3/21/2021 MILAGE ON VEHICLE WAS74757 FORD CUSTOMERS SERVICE WAS UNRESPONSIVE TO PROBLEM
I HAVE A HISSING NOISE WHEN PRESSING THE BRAKE AND A SOFTER FEELING WHEN PUSHING THE BRAKE. THIS HAPPENS WHEN I COME TO A COMPLETE STOP OR WHEN I'M IDLING. MY VEHICLE WAS BUILT IN THE PLANT THAT HAD A CUSTOMER SATISFACTION PROGRAM OFFER AN EXTENDED WARRANTY TO FIX THIS ISSUE, BUT MY DATE IS 6 MONTHS OFF OF THEIR WINDOW AND THEY …
Read full complaint
I HAVE A HISSING NOISE WHEN PRESSING THE BRAKE AND A SOFTER FEELING WHEN PUSHING THE BRAKE. THIS HAPPENS WHEN I COME TO A COMPLETE STOP OR WHEN I'M IDLING. MY VEHICLE WAS BUILT IN THE PLANT THAT HAD A CUSTOMER SATISFACTION PROGRAM OFFER AN EXTENDED WARRANTY TO FIX THIS ISSUE, BUT MY DATE IS 6 MONTHS OFF OF THEIR WINDOW AND THEY WON'T COVER IT.
SPONGY SOFT BRAKE PEDAL DUE TO FAULTY ABS BRAKE MANIFOLD VALVE, (AS DIAGNOSIS FROM REPAIR SHOP) WHILE BRAKING TO MAKE A LEFT HAND TURN STARTED THE PROBLEM OF SPONGY, DIMINISHED BRAKING CAPACITY, APPLYING BRAKES WOULD RESULT IN A SOFT FADING PEDAL PROBLEM OCCURED WHILE CAR IN MOTION MAKING LEFT HAND TURN FROM HIGHWAY TO ROAD NO…
Read full complaint
SPONGY SOFT BRAKE PEDAL DUE TO FAULTY ABS BRAKE MANIFOLD VALVE, (AS DIAGNOSIS FROM REPAIR SHOP) WHILE BRAKING TO MAKE A LEFT HAND TURN STARTED THE PROBLEM OF SPONGY, DIMINISHED BRAKING CAPACITY, APPLYING BRAKES WOULD RESULT IN A SOFT FADING PEDAL PROBLEM OCCURED WHILE CAR IN MOTION MAKING LEFT HAND TURN FROM HIGHWAY TO ROAD NORMAL BRAKING CONDITION
THE ABS WENT OUT. BRAKES WENT ALL THE WAY TO THE FLOOR. ON A SEPARATE OCCASION, A BRAKE LINE GAVE OUT AND WAS LEAKING' THAT NEEDED TO BE FULLY REPLACED' POWER BRAKE BOOSTER AND MASTER CYLINDER NEEDED TO BE REPLACED' THIS ALL HAPPENED WITHIN 4-5 MONTHS. THE WRENCH IDIOT LIGHT CAME ON AND THERE WAS LOSE OF POWER. IT HAS COME …
Read full complaint
THE ABS WENT OUT. BRAKES WENT ALL THE WAY TO THE FLOOR. ON A SEPARATE OCCASION, A BRAKE LINE GAVE OUT AND WAS LEAKING' THAT NEEDED TO BE FULLY REPLACED' POWER BRAKE BOOSTER AND MASTER CYLINDER NEEDED TO BE REPLACED' THIS ALL HAPPENED WITHIN 4-5 MONTHS. THE WRENCH IDIOT LIGHT CAME ON AND THERE WAS LOSE OF POWER. IT HAS COME ON MULTIPLE TIMES BUT THEN GOES AWAY AND THEN THE CAR IS FINE.
FAILURE OF THE BRAKE BOOSTER. THIS ALLOWS THE BRAKE PEDAL TO GO ALMOST TO THE FLOOR, REQUIRING A LONGER STOPPING DISTANCE AND MORE PRESSURE ON THE BRAKE PEDAL. MY WIFE TOLD ME ABOUT THIS OCCASIONAL BEGINNING ABOUT 1.5 YEARS AGO BUT I WAS UNABLE TO DUPLICATE IT. THIS PAST WEDNESDAY FEBRUARY 17, 2021, WHILE I WAS DRIVING THE CAR A…
Read full complaint
FAILURE OF THE BRAKE BOOSTER. THIS ALLOWS THE BRAKE PEDAL TO GO ALMOST TO THE FLOOR, REQUIRING A LONGER STOPPING DISTANCE AND MORE PRESSURE ON THE BRAKE PEDAL. MY WIFE TOLD ME ABOUT THIS OCCASIONAL BEGINNING ABOUT 1.5 YEARS AGO BUT I WAS UNABLE TO DUPLICATE IT. THIS PAST WEDNESDAY FEBRUARY 17, 2021, WHILE I WAS DRIVING THE CAR AT VARIOUS SPEEDS, IT FAILED COMPLETELY. IN 2014 FORD ISSUED CSP 13N02 TO CORRECT THIS PROBLEM ON 2010-2013 FORD EDGE VEHICLES. THIS WAS NOT A RECALL, BUT IT SHOULD BE. MY WIFE NEVER RECEIVED NOTIFICATION FROM FORD OR THE SELLING DEALERSHIP ABOUT THIS. WE MADE AN APPOINTMENT FOR TODAY, FEBRUARY 21, 2021, AT THE SELLING DEALERSHIP. WHEN WE DROPPED IT OFF I INFORMED THEM OF THE PROBLEM, AS WELL AS CSP 13N02. SINCE HER VEHICLE HAD JUST OVER THE 150,000 MILE LIMIT FOR THE CSP THEY REFUSED TO PERFORM THE WORK UNDER THE TERMS OF THAT CSP. THAT CSP HAS A PARTS COST OF $200 AND ALLOWS 2 HOURS LABOR. THEY HAVE QUOTED HER $700+. THE CAR HAS BEEN LEFT THERE FOR REPAIR SINCE WE HAVE NO OTHER CHOICE. THERE SHOULD BE A RECALL INITIATED FOR THIS DANGEROUS SITUATION.
Official recalls
214V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration