The ABS Control Module failed in my 2013 Ford Edge. I no longer have anti-lock brakes and my wife does not feel safe driving the car. I talked to a number of different Ford Dealerships and every service technician I talked to told me they don't know how this issue is not a recall as it is happening so often that the part is ba…
Read full complaint
The ABS Control Module failed in my 2013 Ford Edge. I no longer have anti-lock brakes and my wife does not feel safe driving the car. I talked to a number of different Ford Dealerships and every service technician I talked to told me they don't know how this issue is not a recall as it is happening so often that the part is back ordered by a year. I had the problem confirmed by in independent service center and was informed to bring to a Ford Dealership. The vehicle is now at a Ford Dealership awaiting diagnosis but they all said they know what the problem is and they can't get the part. There are multiple warning lamps going off when you start the vehicle. ABS warning lamp, service advancetrac lights and brake warning lamps. This issue just popped up and we brought to an independent service center to get fixed and they were aware of this issue and told me that you can't get the part and to contact Ford. They also told us that if you push the brakes too hard it could cause them to lock up which is a huge safety concern and now my wife will not drive the vehicle and I can not sell it to anyone like that so we are stuck. Please help.
NHTSA ODI #11711907
Mileage unknown · Jan 15, 2026
Forward Collision AvoidanceService Brakes
This is on a 2013 Ford Edge with Adaptive Cruise Control. The brakes failed and went completely to the floor, putting the driver/passengers at danger along with other vehicles in the vicinity. The ABS control module with HCU is the part that failed. Ford part # CT4Z-2C405-A. Per the dealership and per Ford, this part is now …
Read full complaint
This is on a 2013 Ford Edge with Adaptive Cruise Control. The brakes failed and went completely to the floor, putting the driver/passengers at danger along with other vehicles in the vicinity. The ABS control module with HCU is the part that failed. Ford part # CT4Z-2C405-A. Per the dealership and per Ford, this part is now obsolete and unavailable, which means the vehicle is currently unsafe to drive and unusable. Ford does not have any plan at the moment to correct this issue.
NHTSA ODI #11711271
Mileage unknown · Jan 10, 2026
Forward Collision AvoidanceService Brakes
The brake booster had a recall but it should have never just have been the booster. The brake system on this is dangerous. I had the booster replaced and the valve got stuck in the HCU and cause brakes to fail. This has been a common issue amongst people and yet this is not a recall. The dealership just quoted me $3200. That's a…
Read full complaint
The brake booster had a recall but it should have never just have been the booster. The brake system on this is dangerous. I had the booster replaced and the valve got stuck in the HCU and cause brakes to fail. This has been a common issue amongst people and yet this is not a recall. The dealership just quoted me $3200. That's absurd for an issue thats obviously a common huge problem for people
NHTSA ODI #11710105
Mileage unknown · Jan 2, 2026
Service Brakes
Soft brake pedal that goes to floor
NHTSA ODI #11708452
Mileage unknown · Dec 15, 2025
Service BrakesSuspension
While driving the car approaching a stop the brake pedal suddenly went almost all the way to the floor. Had to press the brake multiple times to come to a complete stop. It is unsafe when traveling in traffic and unable to slow down fast enough to stop the vehicle which can cause an accident. The vehicle has not been inspected. …
Read full complaint
While driving the car approaching a stop the brake pedal suddenly went almost all the way to the floor. Had to press the brake multiple times to come to a complete stop. It is unsafe when traveling in traffic and unable to slow down fast enough to stop the vehicle which can cause an accident. The vehicle has not been inspected. Contacted a mechanic and described the issue and stated this sound like a master cylinder issue and it is unsafe to drive. This issue did not present warning lights or message to indicate there was anything wrong. We have read many similar complaints online. We believe Ford should fix this issue.
NHTSA ODI #11705205
Mileage unknown · Dec 9, 2025
Service Brakes
While driving the car approaching a stop the brake pedal suddenly went almost all the way to the floor. It stayed that way for the next couple of days before going back to a fully functioning brake pedal. Months later it happened again this time without repairing itself. We took it to a local mechanic as well as the local Ford d…
Read full complaint
While driving the car approaching a stop the brake pedal suddenly went almost all the way to the floor. It stayed that way for the next couple of days before going back to a fully functioning brake pedal. Months later it happened again this time without repairing itself. We took it to a local mechanic as well as the local Ford dealership twice. Their computer did not detect anything wrong and yet when the service rep tried the brakes they went clear to the floor! So we had them update the computer software in the car since we never had any warning lights about this issue. The local mechanic as well as the Ford dealership suspect it is the HCU unit within the ABS system. The problem is there are no replacement parts available to remedy the problem. We have read many similar complaints online. We believe Ford should fix this issue.
NHTSA ODI #11704020
Mileage unknown · Dec 8, 2025
EngineFuel/propulsion SystemService Brakes
I purchased this vehicle used in August 2025 from the estate of a friend's relative. The records show it was meticulously maintained and no recall notices have been unaddressed. The prior owner used it infrequently and it still has just under 90k miles. There were no major engine issues when my local repair shop (over 12 years a…
Read full complaint
I purchased this vehicle used in August 2025 from the estate of a friend's relative. The records show it was meticulously maintained and no recall notices have been unaddressed. The prior owner used it infrequently and it still has just under 90k miles. There were no major engine issues when my local repair shop (over 12 years and 3 vehicles) inspected all systems, and the vehicle passed for PA state inspection and emissions. However, driving more, I noticed that the brakes would intermittently become "mushy" or "hard" and overall less responsive. I needed to use a lot of force to fully stop over a longer distance. There was also a hissing noise while braking and sometimes the cabin air fan would blast on suddenly. Then, while stopped at a red light and applying the brakes, the engine shut off and check engine light came on. My mechanic detected O2 sensor codes P2195/P2197 indicating "stuck lean." But nothing about the brake booster, and so we cleaned it up a bit and tried to get more of an understanding of the issue. Now I know that the compromised engine vacuum from the booster air leak is impacting the fuel/air balance. Extremely unsafe. This has now happened MANY times while I try to get a good diagnosis and help. It's scary, and makes city driving very challenging. On multiple occasions I feared I would hit other vehicles or would have to "creep" at a light to alleviate the airflow issues from braking. If I have to be at a light for more than a moment, I will put the car in park and foot off the brake. I'd rather risk being honked at or hit, than have the engine dying on me in traffic. When I was able to get to a dealership, I was informed that it was the brake booster. The first thing I found when looking up that part for the 2013 Ford Edge was the recall. The dealership says my VIN was not covered, but it seems more than coincidence that this is the exact problem, now confirmed by the dealership. The part is faulty, and should be replaced by OEM.
NHTSA ODI #11703726
Mileage unknown · Sep 24, 2025
Service Brakes
The 2013 Ford Edge began giving trouble after sitting at an intersection or pulling out of the driveway to enter major traffic. The vehicle would hesitate to accelerate as though it is running out of gas but it isn't out of gas. When you continue pressing on the accelerator it would jerk then accelerate. We barely escaped being …
Read full complaint
The 2013 Ford Edge began giving trouble after sitting at an intersection or pulling out of the driveway to enter major traffic. The vehicle would hesitate to accelerate as though it is running out of gas but it isn't out of gas. When you continue pressing on the accelerator it would jerk then accelerate. We barely escaped being hit from the rear because the vehicle died while pulling out onto the feeder, whereupon I struggled to pull into a nearby gas station. The brake pedal is generally stiff but can be depressed, however, in other instances, when braking the brake pedal sometimes becomes hard to depress but becomes easier after the car is driving for a long stretch, such as the freeway. When you start the car the panel is normal but as you begin driving the Check Brake System failure light begins to appear in Red and the ABS light and the oil light. Similar incidents as the previously mentioned situations have happened on numerous occasions.
NHTSA ODI #11689481
Mileage unknown · Aug 25, 2025
Service Brakes
Replaced Master Brake Cylinder and Brake Booster due to hard Braking. Also, ABS Control lights are illuminated. Codes show failed ABS module creating safety issue when fast breaking. Brake pushes down to the floor periodically Repair is very costly to fix.
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
2013 Ford Edge Problems, Complaints & Recalls | Skip That Year
Illustration