IllustrationI am having problems once again with my brake booster...I had to have it replaced twice so far in the last 2 years. And now i suddenly have to push much harder on my brakes to stop my car & therefore have it repaired or replaced, yet again.
2013 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
Service Brakes complaints
529 reportsWhile driving on 2 lane highway coming to a Stop sign, brake pedal depressed all the way to the floor without fully stopping vehicle. There was a hissing sound when depressing the pedal. Had to implement the emergency parking brake in order to stop completely. There were no warning lights and this has not happened before. I drov…
Read full complaint
While driving on 2 lane highway coming to a Stop sign, brake pedal depressed all the way to the floor without fully stopping vehicle. There was a hissing sound when depressing the pedal. Had to implement the emergency parking brake in order to stop completely. There were no warning lights and this has not happened before. I drove it home with hazard lights on and at every stop I pumped the brakes, heard the hissing sound but pedal goes to floor. When got home I checked brake fluid reservoir, it was full. I do not see any fluid leaks on driveway. I checked a Ford forum and see many incidents like this described, too many. Apparently this is a known issue by Ford and there is a TSB 13N02 (brake booster). This could have been a horrible incident if there had been other cars in the intersection.
I have a 2013 ford edge and I was driving at 40=45 mph and when I came up to a light the brake peddle went to the floor and was very hard to stop. The result was me having to leave the road to the right to avoid a collision. I took it to ford who stated it needed a brake booster and said my vehicle doesn't qualify for an extend…
Read full complaint
I have a 2013 ford edge and I was driving at 40=45 mph and when I came up to a light the brake peddle went to the floor and was very hard to stop. The result was me having to leave the road to the right to avoid a collision. I took it to ford who stated it needed a brake booster and said my vehicle doesn't qualify for an extended warranty on the booster. Car had 88k miles at time of incident.prior to the incident no lights or signs. After this I hear a loud hissing noise from under dash.
When I hit a pot hole or bump I have no brakes. They go all the way to the floor. My mechanic will not touch them due to brake failure on all the Ford edges. I was told To contact you.
Since first purchasing the vehicle from Larry H. Ford in Mesa, AZ in 2019 and returning it for repair due to inoperable brakes, the issue has returned time and time again. It is now happening again where I either have to either press the brake peddle completely to the floor or the vehicle will not come to a complete stop at all.…
Read full complaint
Since first purchasing the vehicle from Larry H. Ford in Mesa, AZ in 2019 and returning it for repair due to inoperable brakes, the issue has returned time and time again. It is now happening again where I either have to either press the brake peddle completely to the floor or the vehicle will not come to a complete stop at all. This has become extremely costly and I would like to know if this is an issue specifically associated with the 2013 Ford Edge and find some resolve.
Brake vacuum pressure system went out. Only 101k miles and 10 years old......
The abs module has gone bad numerous times and is in a shop again for the third time in two month. I've havent been able to drive my car for two months at first it was the master cylinder and then the abs unit and then the brake booster and now the new abs unit again! After extensive research my husband and I found that this is …
Read full complaint
The abs module has gone bad numerous times and is in a shop again for the third time in two month. I've havent been able to drive my car for two months at first it was the master cylinder and then the abs unit and then the brake booster and now the new abs unit again! After extensive research my husband and I found that this is very common in my vechile model but not enough cars to be issued a recall. Which I think is a massive safety issue because your brakes are very important. If your brakes fail you, you could not only injure yourself and your passengers but others around you. Right now my vehicle is at my local ford dealership and they also agree that this is a very common problem and ford isn't recalling them and making customers pay thousands of dollars for the new part and service. I was even told some times you don't get a working abs unit and have to keep going through the service part warranty until you get a good one. Which I feel causes more lost time with my vehicle staying in the shop until I get a good one.
when was driving pushed the brakes and it went straight to floor almost causing me to rear end the car in front of me. dealer said said it is the booster. no police or manufacturer inspection. no warning lights or any other symptoms
I was driving on the highway and someone rapidly stopped in front of me. When I went to push my brakes, my brake pedal with straight to the floor and the car would not stop, almost causing a collision with the car in front of me. Brake system failed, no warning lights. This has been an known issue with this car for others but st…
Read full complaint
I was driving on the highway and someone rapidly stopped in front of me. When I went to push my brakes, my brake pedal with straight to the floor and the car would not stop, almost causing a collision with the car in front of me. Brake system failed, no warning lights. This has been an known issue with this car for others but still no recall.
The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed and approaching a stop light, the brake pedal was depressed but was extremely firm. The brakes failed to respond as needed. The driver placed both feet on the brake pedal and the vehicle stopped. The contact pulled over, and her husb…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed and approaching a stop light, the brake pedal was depressed but was extremely firm. The brakes failed to respond as needed. The driver placed both feet on the brake pedal and the vehicle stopped. The contact pulled over, and her husband drove the vehicle to the residence. The contact stated that while her husband was driving at an undisclosed speed, the failure recurred. There were no warning lights illuminated. The vehicle was taken to the local dealer where it was diagnosed that the brake booster needed to be replaced. The vehicle was repaired. The manufacturer was contacted but no assistance was provided. The approximate failure mileage was 151,049.
Official recalls
214V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.