NHTSA owner reports · September 18, 2026 snapshot.
Power Train complaints
160 reportsClear category filter94,000 miles · Aug 14, 2024
Power Train
The contact owns a 2013 Ford Edge. The contact stated while driving at various speeds, the vehicle shuddered and there was an abnormally loud sound coming from the rear of the vehicle. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that the rear differential had failed and needed to be re…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving at various speeds, the vehicle shuddered and there was an abnormally loud sound coming from the rear of the vehicle. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that the rear differential had failed and needed to be replaced. The vehicle was not repaired. The dealer and the manufacturer were not notified of the failure. The failure mileage was approximately 94,000.
NHTSA ODI #11608565
114,000 miles · Apr 23, 2024
Power Train
The contact owns a 2013 Ford Edge. The contact stated while driving 45 MPH, upon acceleration, the vehicle began to shake and shudder. The check engine warning light was illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the torque converter, hoses, and transmission needed to be replaced. The veh…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving 45 MPH, upon acceleration, the vehicle began to shake and shudder. The check engine warning light was illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the torque converter, hoses, and transmission needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 114,000.
NHTSA ODI #11584760
Mileage unknown · Feb 4, 2024
EnginePower Train
Put car in for regular service, and to investigate burning smell and transmission slippage. Mechanic found that the Power Transfer Unit (PTU) was completely filled with a paste-like sludge. (he has pictures) Mechanic says that the PTU is too close to the catalytic converter, therefore overheating the PTU and literally boiling …
Read full complaint
Put car in for regular service, and to investigate burning smell and transmission slippage. Mechanic found that the Power Transfer Unit (PTU) was completely filled with a paste-like sludge. (he has pictures) Mechanic says that the PTU is too close to the catalytic converter, therefore overheating the PTU and literally boiling the transfer fluid. He was able to clean the module, but says there's still a leak around the PTU seal. The work required to replace the seal, would also merit replacing the PTU. BUT, this is a $800 part! The safety risk would have been my transmission completely seizing up and causing an accident due to mechanical failure. The vehicle has had all of it's regular and milestone service work performed. No warning lights went off. I'm on borrowed time with this part and/or new transmission. Will there be a remedy to prevent this in the future?
NHTSA ODI #11569758
80,000 miles · Dec 8, 2023
Power Train
The contact owns a 2013 Ford Edge. The contact stated that while shifting to park(P), the message “Shift to Park” was displayed. The contact had to park and turn off and restart the vehicle and press the button on the gear shifter several times before the message would cease to appear. The vehicle was taken to the dealer who dia…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while shifting to park(P), the message “Shift to Park” was displayed. The contact had to park and turn off and restart the vehicle and press the button on the gear shifter several times before the message would cease to appear. The vehicle was taken to the dealer who diagnosed that the gear shifter had failed and needed to be replaced. The vehicle had not been repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline. The approximate failure mileage was 80,000.
NHTSA ODI #11559149
150,000 miles · Oct 25, 2023
Power Train
The contact owns a 2013 Ford Edge. The contact stated while driving at various speeds, the vehicle suddenly lost motive power and failed to accelerate or move forward. After turning off and restarting the vehicle, the vehicle operated normally. The contact stated that during the failure, the message "Power Train Malfunction" was…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving at various speeds, the vehicle suddenly lost motive power and failed to accelerate or move forward. After turning off and restarting the vehicle, the vehicle operated normally. The contact stated that during the failure, the message "Power Train Malfunction" was displayed. The vehicle was taken to the local mechanic who was unable to determine the cause of the failure. The local dealer was notified of the failure. The manufacturer was not notified of the failure. The failure mileage was 150,000.
NHTSA ODI #11551751
Mileage unknown · Oct 20, 2023
Power TrainService BrakesWheels
I purchased my Ford from a used car lot and only 3 months later without any alerts my brake pedal goes to the floor. It makes a hissing sound like air being released. My brakes and fluid are fine? Why are their recalls on my same year vehicle, but not mine. I understand replacing brake booster, master cylinder will NOT help.…
Read full complaint
I purchased my Ford from a used car lot and only 3 months later without any alerts my brake pedal goes to the floor. It makes a hissing sound like air being released. My brakes and fluid are fine? Why are their recalls on my same year vehicle, but not mine. I understand replacing brake booster, master cylinder will NOT help. Now I am broke from purchasing my Ford, I can't afford to dump more money into a vehicle that can't be fixed. You need to recall the entire car! Now my dash lights go crazy, even ABS once? This car is a freaking lemon and someone is going to get hurt. Then Ford will responsible for their manufactory error?
NHTSA ODI #11550942
100,000 miles · Oct 2, 2023
Power Train
The contact owns a 2013 Ford Edge. The contact stated that while driving at 35 MPH, the vehicle suddenly came to a complete stop. The contact stated that the front driver’s side tire had nearly detached from the vehicle. The contact was uncertain if any warning lights were illuminated. Due to the failure occurring in the middle …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving at 35 MPH, the vehicle suddenly came to a complete stop. The contact stated that the front driver’s side tire had nearly detached from the vehicle. The contact was uncertain if any warning lights were illuminated. Due to the failure occurring in the middle of a busy roadway, Police were called, and the vehicle was towed to a parking lot where it remained. Upon arrival to the scene, the tow truck driver alerted the contact NHTSA Campaign Number: 14V393000 (Power Train). The manufacturer was notified, and the contact was informed that there were no recalls on the VIN related to the failure. The vehicle was not repaired. The failure mileage was approximately 100,000.
NHTSA ODI #11547744
104,542 miles · Sep 27, 2023
Power TrainService BrakesSteering
While I was driving my Ford Edge 2013 limited, the car shuts off and I lost control of the steering wheel and brakes. I almost hit a pole do the steering wheel going hard. I’m not the only person with this I problem. This happened to me before.
NHTSA ODI #11546917
Mileage unknown · Aug 7, 2023
Power Train
Transfer case on vehicle started rattling.
NHTSA ODI #11536833
74,000 miles · Jul 25, 2023
Power Train
The contact owns a 2013 Ford Edge. The contact stated that while the vehicle was at an independent mechanic for an oil change, the contact was informed that the Power Transfer Unit (PTU) was leaking and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while the vehicle was at an independent mechanic for an oil change, the contact was informed that the Power Transfer Unit (PTU) was leaking and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 74,000.
NHTSA ODI #11534346
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration