The driver side passenger "door ajar" sensor stays on constantly and is unsafe because we aren't sure if the door is truly open or not? We are scared to have passengers sit on that side of the vehicle for fear of the door flying open and causing injury by falling out or other injury because the sensor does not tell us accuratel…
Read full complaint
The driver side passenger "door ajar" sensor stays on constantly and is unsafe because we aren't sure if the door is truly open or not? We are scared to have passengers sit on that side of the vehicle for fear of the door flying open and causing injury by falling out or other injury because the sensor does not tell us accurately as to whether the door is truly closed all the way or not. It also drains the battery over time due to constantly being on. This problem has been going on for 2 years. We had it looked at by a mechanic. We were told they can replace the sensor, but it would likely go out again because this is a manufacturer defect, and a well known problem for Ford Edges as well as other Ford models, but they refuse to issue a recall. This is EXTREMELY UNSAFE. The other safety concern I have is the need for a recall on our VIN SPECIFIC rear view camera. The screen went blank and then, when it came back on, the image is flipped upside down and has vertical lines across the screen making it extremely difficult to see. This is a crucial component to safety. This happened approximately 1 year ago. This is EXTREMELY UNSAFE as we can back over and KILL someone if we don't go super slow and intensely observe the camera while in reverse. This is even more dangerous in poorly lit places. There were no warnings or sensors indicating a problem with the camera. It just went blank and then PERMANENTLY flipped the image upside down.
NHTSA ODI #11693584
Mileage unknown · Sep 24, 2025
Back Over PreventionElectrical System
The rearview camera does not function properly. Most of the time, it shows a blank screen or nothing at all. Sometimes it tells me to contact the dealership. Other times, it shows the camera view but upside down. It puts myself and others at risk because I can't see clearly when I am backing up. The problem is covered by a known…
Read full complaint
The rearview camera does not function properly. Most of the time, it shows a blank screen or nothing at all. Sometimes it tells me to contact the dealership. Other times, it shows the camera view but upside down. It puts myself and others at risk because I can't see clearly when I am backing up. The problem is covered by a known recall. However, my vehicle is not covered by the recall.
NHTSA ODI #11689459
Mileage unknown · Sep 11, 2025
Electrical System
The rear back up camera intermittantly fails on this vehicle. About 70% of the time, it displays a black screen. The screen will display "Contact Dealership." This has been occurring for approx. 1 year.
NHTSA ODI #11686497
Mileage unknown · Sep 9, 2025
Electrical SystemUnknown Or Other
It is my rear view camera. I would put the vehicle in reverse and it will sometimes start to work and than it will shut off and a message comes across saying I need to contact dealership. It will sometimes come up and be upside down or I will put the vehicle in reverse and the back up camera just flashes while in use. I have no…
Read full complaint
It is my rear view camera. I would put the vehicle in reverse and it will sometimes start to work and than it will shut off and a message comes across saying I need to contact dealership. It will sometimes come up and be upside down or I will put the vehicle in reverse and the back up camera just flashes while in use. I have not taken the vehicle to the shop. I have called and they said it sounds electrical. But the recall you just released on 2015 Ford edges for the back up camera is the same thing that is going on with my vehicle and I have a 2013.
NHTSA ODI #11685927
Mileage unknown · Jun 3, 2025
Electrical System
Last week my back up camera said there was a system error and only works sometimes now. I almost hit somebody because it started showing it was working and then it went black and then wouldn’t work again. I also have a video where it starts to show me backing up and then cuts out to being black and seeing contact your dealership…
Read full complaint
Last week my back up camera said there was a system error and only works sometimes now. I almost hit somebody because it started showing it was working and then it went black and then wouldn’t work again. I also have a video where it starts to show me backing up and then cuts out to being black and seeing contact your dealership. I did contact the dealership and they said there is not a recall in regards to my car specifically.
NHTSA ODI #11664516
Mileage unknown · May 28, 2025
Electrical SystemUnknown Or OtherVisibility/wiper
Rear view (back up) camera works only on and off. The screen goes black and a warning to contact the dealer shows up. It is getting more and more frequent lately. I am having a very hard time in crowded parking lots. Now it has stopped completely.
NHTSA ODI #11663319
Mileage unknown · Apr 16, 2025
Electrical SystemExterior Lighting
Interior lights stay on much too long after turning vehicle off, even several hours. Dash and bell indicators indicates doors are open when they are not. Door locks operate open while driving.
NHTSA ODI #11654925
Mileage unknown · Feb 25, 2025
Electrical SystemExterior LightingStructure
Driving on the highway at night when suddenly the door alarm rings, dome light turned on causing driver to lose focus/control. Was driving at 60mph when the sensor faulted. The alarm/notification turns on at random times causing the vehicle to have the light stay on and drain battery. This is causing the driver unsure if the doo…
Read full complaint
Driving on the highway at night when suddenly the door alarm rings, dome light turned on causing driver to lose focus/control. Was driving at 60mph when the sensor faulted. The alarm/notification turns on at random times causing the vehicle to have the light stay on and drain battery. This is causing the driver unsure if the door is properly closed and risking the door opening in case of an accident. Problem has persisted.
NHTSA ODI #11644870
Mileage unknown · Feb 7, 2025
Electrical SystemService BrakesSteering
If you hit a pot hole or a bump on the road the brake pedal makes a weird sound and then the brake goes all the way to the floorboard when trying to apply brakes and doesn't come to an immediate stop. The wrench light has come on or the symbol that has the car and wavy lines for traction control will turn on all of a sudden and…
Read full complaint
If you hit a pot hole or a bump on the road the brake pedal makes a weird sound and then the brake goes all the way to the floorboard when trying to apply brakes and doesn't come to an immediate stop. The wrench light has come on or the symbol that has the car and wavy lines for traction control will turn on all of a sudden and then the car shuts off in the middle of the road while driving putting my life in danger. It also doesn't accelerate all of a sudden and loses power while driving putting my life in danger. When you put the car in park the car still jerks forward even after the car is in park and off. It also makes a clicking sound as if it goes into gear after you have turned the car off and park has been engaged. The headlights keep shutting off while driving or dimming in their own. The motormount screws came undone and I had to get it repaired. The power steering keeps losing the fluid and makes a loud grinding noise especially during cold weather. Makes a loud whistle sound like a turbo jet engine when it's cold and you start driving. The rear driverside door latch keeps making the car alert that the door is open when it is not. The recall only shows door latch for a different door and dealership won't repair with recall notice because the notice doesn't say all door latches and is specific to a different door. The car is unsafe to drive but it's the only car I have and the last time I took it to get repairs they kept it for a month and my it off pocket costs were close to $1600 dollars which put me in a financial strain. I can not afford to be without my car for that long again and pay for things that shouldn't be falling apart and putting my child's and my life in danger.
NHTSA ODI #11641244
Mileage unknown · Jan 24, 2025
Electrical System
The screen just completely goes white off and on no matter when you’re driving. I turned the car off and on, and it still would do it.. I don’t know why it happens. Sometimes it also won’t even connect to Bluetooth.. I can turn my phone off and on, and it still won’t connect to it.. something is definitely wrong with it.
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
2013 Ford Edge Problems, Complaints & Recalls | Skip That Year
Illustration