NHTSA owner reports · September 18, 2026 snapshot.
Back Over Prevention complaints
45 reportsClear category filterMileage unknown · Sep 23, 2025
Back Over PreventionUnknown Or Other
A few years ago, I brought my Edge into a dealership in Shawnee Mission, KS (Shawnee Mission Ford) for the rearview camera malfunctioning. What occurs is, once I put the car in reverse, the camera will, sometimes come on, once I begin backing out, the camera will shut off and a message will appear. On some occasions, the camera …
Read full complaint
A few years ago, I brought my Edge into a dealership in Shawnee Mission, KS (Shawnee Mission Ford) for the rearview camera malfunctioning. What occurs is, once I put the car in reverse, the camera will, sometimes come on, once I begin backing out, the camera will shut off and a message will appear. On some occasions, the camera will operate, but 9 times out of 10 it will always go black with a pop up message. I want my vehicle to be included in the recall if the backup camera is the issue please.
NHTSA ODI #11689194
193,000 miles · Sep 23, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while attempting to start the vehicle, the contact became aware that the rearview camera displayed a blank screen or an upside-down image. An independent mechanic was contacted. The vehicle was not taken to a dealer or an independent mechanic to be diagnosed. The vehicle…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while attempting to start the vehicle, the contact became aware that the rearview camera displayed a blank screen or an upside-down image. An independent mechanic was contacted. The vehicle was not taken to a dealer or an independent mechanic to be diagnosed. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 25V270000 (BACK OVER PREVENTION); however, the VIN or the model year was not included in the recall. The manufacturer was not notified of the failure. The failure mileage was approximately 193,000.
NHTSA ODI #11689174
Mileage unknown · Sep 13, 2025
Back Over PreventionUnknown Or Other
The backup camera stopped working consistently in June 2025. Safety recall has been issued for 2015 vehicles and newer, but not for 2013 and 2014 years. Ford dealer said the camera needs to be replaced for $740, but numerous online comments show other Ford owners with the same issue starting at the same time. I believe this is a…
Read full complaint
The backup camera stopped working consistently in June 2025. Safety recall has been issued for 2015 vehicles and newer, but not for 2013 and 2014 years. Ford dealer said the camera needs to be replaced for $740, but numerous online comments show other Ford owners with the same issue starting at the same time. I believe this is a software issue, and would like 2013 Ford Edge to be added to safety recall.
NHTSA ODI #11687037
60,953 miles · Sep 9, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while attempting to reverse, the back over prevention camera malfunction and failed to display an image. There was no warning light illuminated. The vehicle was taken to a local auto body shop where it was diagnosed, and the contact was informed that the camera was fault…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while attempting to reverse, the back over prevention camera malfunction and failed to display an image. There was no warning light illuminated. The vehicle was taken to a local auto body shop where it was diagnosed, and the contact was informed that the camera was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 60,953.
NHTSA ODI #11686123
122,000 miles · Aug 14, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while shifted into reverse(R), the camera image on the front display screen was black and the message "Contact Dealer" was displayed. The contact stated that the image was constantly black, and the camera or the display had stopped functioning. The contact researched onl…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while shifted into reverse(R), the camera image on the front display screen was black and the message "Contact Dealer" was displayed. The contact stated that the image was constantly black, and the camera or the display had stopped functioning. The contact researched online and related the failure to NHTSA Campaign Number: 25V442000 (Back Over Prevention); however, the VIN was not included in the recall. The contact notified the manufacturer and was informed that the VIN was not included in the recall. The manufacturer referred the contact to the NHTSA Hotline. The failure mileage was approximately 122,000.
NHTSA ODI #11680749
159,000 miles · Jul 30, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rearview camera image was black. The contact stated that the failure was intermittent. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact related the failure to an unknown recall; however, the VIN was not inc…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rearview camera image was black. The contact stated that the failure was intermittent. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact related the failure to an unknown recall; however, the VIN was not included in the recall. The manufacturer was made aware of the failure, but no assistance was provided. The contact was advised to contact the NHTSA Hotline to report the safety failure. The failure mileage was approximately 159,000
NHTSA ODI #11677256
63,000 miles · Jul 30, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated while in reverse(R), the rearview camera displayed a blank image. Additionally, the contact also stated that upon shifting to drive(D), the rearview camera remained activated temporarily. The vehicle was taken to the dealer, where the contact was informed that the VIN was not…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while in reverse(R), the rearview camera displayed a blank image. Additionally, the contact also stated that upon shifting to drive(D), the rearview camera remained activated temporarily. The vehicle was taken to the dealer, where the contact was informed that the VIN was not included in a recall, and the contact was provided an estimated fee for the repair. The contact declined to pay for the repair. The vehicle was not repaired. The manufacturer was notified of the failure and a case was filed. The contact was then referred to the NHTSA Hotline to file a vehicle safety complaint. The failure mileage was approximately 63,000.
NHTSA ODI #11677215
195,000 miles · Jul 11, 2025
Back Over PreventionPower Train
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rearview camera image was black and the message "Camera Not Available" was displayed. Additionally, the contact stated that the vehicle had failed to accelerate as needed while depressing the accelerator pedal. The vehicle was taken to the local ind…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rearview camera image was black and the message "Camera Not Available" was displayed. Additionally, the contact stated that the vehicle had failed to accelerate as needed while depressing the accelerator pedal. The vehicle was taken to the local independent mechanic who was unable to determine the cause of the failure. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was 195,000.
NHTSA ODI #11672670
50,000 miles · Jun 24, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that the backup prevention camera occasionally went blank while attempting to reverse, and operated as designed occasionally. The message “Camera Unavailable” was displayed. The vehicle was taken to an independent mechanic who was unable to duplicate the failure. The contact …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that the backup prevention camera occasionally went blank while attempting to reverse, and operated as designed occasionally. The message “Camera Unavailable” was displayed. The vehicle was taken to an independent mechanic who was unable to duplicate the failure. The contact called the local dealer and was referred to the Ford Recall center for assistance. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 50,000.
NHTSA ODI #11668944
35,000 miles · Jun 20, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rearview camera image was distorted or blue. The message "Rearview Camera Unavailable" was intermittently displayed. The vehicle was taken to the dealer, where it was diagnosed and determined that the rearview camera had failed and needed to be repla…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rearview camera image was distorted or blue. The message "Rearview Camera Unavailable" was intermittently displayed. The vehicle was taken to the dealer, where it was diagnosed and determined that the rearview camera had failed and needed to be replaced. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 35,000.
NHTSA ODI #11668081
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration