NHTSA owner reports · September 18, 2026 snapshot.
Back Over Prevention complaints
45 reportsClear category filterMileage unknown · Jul 2, 2026
Back Over Prevention
Back up camera displays upside down image when vehicle is placed in Reverse making it extremely difficult to determine images pertaining to the safe operation of my vehicle while performing backing up or checking for obstacles; i.e. pedestrians, pets, bicycles, nearby vehicles or other objects that can cause damage to my vehicle…
Read full complaint
Back up camera displays upside down image when vehicle is placed in Reverse making it extremely difficult to determine images pertaining to the safe operation of my vehicle while performing backing up or checking for obstacles; i.e. pedestrians, pets, bicycles, nearby vehicles or other objects that can cause damage to my vehicle. My vehicle was purchased in 2025 and was informed that this has been a known issue by Ford but a recall has not been issued yet.
NHTSA ODI #11747938
Mileage unknown · Jun 18, 2026
Back Over PreventionElectrical SystemUnknown Or Other
The safety system back up camera has been malfunctioning for 18 months. At times the image will be inverted, at times it will appear to be zoomed in very close, but most of the time it does not work at all. The alerts (beeping) that should be occurring when identifying a hazard do not work. The horn no longer works. Several time…
Read full complaint
The safety system back up camera has been malfunctioning for 18 months. At times the image will be inverted, at times it will appear to be zoomed in very close, but most of the time it does not work at all. The alerts (beeping) that should be occurring when identifying a hazard do not work. The horn no longer works. Several times the entire electrical system will shut off and then reset. There have not been any warning lights on the dash to indicate why this is happening. My vehicle has not been examined by a dealer or independent service center.
NHTSA ODI #11744998
Mileage unknown · Jun 17, 2026
Back Over PreventionUnknown Or Other
On the 2013 Ford edge I own the backup camera fails frequently and without warning. Sometimes the camera will not work at all when the transmission is placed in reverse, other times the camera will fail while during the process of backing up. Problem - does not work at all: When the car is placed in reverse the camera projects …
Read full complaint
On the 2013 Ford edge I own the backup camera fails frequently and without warning. Sometimes the camera will not work at all when the transmission is placed in reverse, other times the camera will fail while during the process of backing up. Problem - does not work at all: When the car is placed in reverse the camera projects a blue screen then states the camera is not available, this happens when it does not work at all. Problem - shuts down while in use: Turns off while in use, one has the rear camera view when backing up, then the camera does one of two things it flips flops (top to bottom) or flashes a blue screen then states the camera is not available. And then sometimes the camera will work for one to three times (the camera is working while backing up, turn the vehicle off, exit / re-enter the vehicle and it works for backing up, but the next time the vehicle is entered and placed in reverse the camera is not working at all and the message reads camera is not available. This has been occurring on a more frequent basis over the last month
NHTSA ODI #11744849
Mileage unknown · May 29, 2026
Back Over PreventionUnknown Or Other
The backup camera glitches repeatedly. Have to put in park then reverse and repeat until it displays. When it is producing the error, the alerts are not received to assist with alerting the driver of any potential hazards and you are unable to see due to camera not working. Also, happened in our 2014 Ford Escape. Although I pa…
Read full complaint
The backup camera glitches repeatedly. Have to put in park then reverse and repeat until it displays. When it is producing the error, the alerts are not received to assist with alerting the driver of any potential hazards and you are unable to see due to camera not working. Also, happened in our 2014 Ford Escape. Although I paid the dealership $600+ to replace it. Now receiving a notice for my 2017 Ford Edge regarding the malfunctioning camera and wondering why either of the other vehicles were not included in this recall.
NHTSA ODI #11740899
141,000 miles · Mar 9, 2026
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the camera was inoperable. The contact referenced NHTSA Campaign Number: 25V572000 (BACK OVER PREVENTION); however, the VIN was not included in the recall. The vehicle was driven to a dealer. The vehicle was repaired. The manufacturer was not notified of…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the camera was inoperable. The contact referenced NHTSA Campaign Number: 25V572000 (BACK OVER PREVENTION); however, the VIN was not included in the recall. The vehicle was driven to a dealer. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 141,000.
NHTSA ODI #11723138
Mileage unknown · Dec 3, 2025
Back Over Prevention
The backup camera rarely works. It either has a black screen, an upside-down image or the image has lines through it. This puts me, my passengers and pedestrians in danger while trying to reverse out of parking spaces. There is a recall for newer Ford Edges but not for a 2013 so Ford is aware of the issue. I also previously …
Read full complaint
The backup camera rarely works. It either has a black screen, an upside-down image or the image has lines through it. This puts me, my passengers and pedestrians in danger while trying to reverse out of parking spaces. There is a recall for newer Ford Edges but not for a 2013 so Ford is aware of the issue. I also previously owned a different 2013 Ford Edge and it had the same problems.
NHTSA ODI #11702737
100,000 miles · Nov 20, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rear-view camera displayed an upside-down and fuzzy image. The vehicle was taken to an independent mechanic, where it was diagnosed with a failed rear-view camera system. The contact was informed that the rear-view camera system needed to be replaced…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rear-view camera displayed an upside-down and fuzzy image. The vehicle was taken to an independent mechanic, where it was diagnosed with a failed rear-view camera system. The contact was informed that the rear-view camera system needed to be replaced. The vehicle was not repaired. The contact referenced an unknown recall; however, the VIN was not under recall. The contact owns another Ford vehicle that experienced a similar failure, and the vehicle was included in the recall. The contact was informed by the independent mechanic to wait for a recall notification for the vehicle. The manufacturer was not made aware of the failure. The failure mileage was approximately 100,000.
NHTSA ODI #11700653
Mileage unknown · Nov 6, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rear-view camera displayed a blurry upside-down image. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact referenced an unknown recall which had a similar failure description; however, the VIN was not included…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the rear-view camera displayed a blurry upside-down image. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact referenced an unknown recall which had a similar failure description; however, the VIN was not included. The manufacturer was not made aware of the failure. The failure mileage was unknown.
NHTSA ODI #11697911
108,000 miles · Oct 23, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated while attempting to start the vehicle, the rearview camera displayed a blank screen and was glitching. A dealer was contacted. The vehicle taken to the dealer where it was diagnosed and determined that the rearview camera needed to be replaced. The vehicle was not repaired. T…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while attempting to start the vehicle, the rearview camera displayed a blank screen and was glitching. A dealer was contacted. The vehicle taken to the dealer where it was diagnosed and determined that the rearview camera needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 25V572000 (BACK OVER PREVENTION); however, the VIN was not included in the recall. The manufacturer was notified of the failure and informed the contact that the VIN was not included in the recall. The failure mileage was 108,000.
NHTSA ODI #11695236
Mileage unknown · Sep 24, 2025
Back Over PreventionElectrical System
The rearview camera does not function properly. Most of the time, it shows a blank screen or nothing at all. Sometimes it tells me to contact the dealership. Other times, it shows the camera view but upside down. It puts myself and others at risk because I can't see clearly when I am backing up. The problem is covered by a known…
Read full complaint
The rearview camera does not function properly. Most of the time, it shows a blank screen or nothing at all. Sometimes it tells me to contact the dealership. Other times, it shows the camera view but upside down. It puts myself and others at risk because I can't see clearly when I am backing up. The problem is covered by a known recall. However, my vehicle is not covered by the recall.
NHTSA ODI #11689459
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration