IllustrationBrake pedal is hard & won't stop vehicle & then goes soft. Has to be pressed to the floor to stop, also makes a high pitched squeal when pushed sometimes.
2011 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2011 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1380–25K
40825–50K
39750–75K
22375–100K
211100–150K
61150K+
1,438 reports with mileage · 363 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 686 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 274 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 261 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
23 crash reports4 fire reports7 injury reports
What owners actually said
1,801 reportsBrakes become hard and then soft. Brake has to be depressed to the floor to stop vehicle. Master Cylinder replaced, Brake booster replaced. Problem is not solved. ABS is the next guess. With all the problems with brakes why isn't Ford taking care of this issue?
The brake pedal goes from easy to press to hard to press and the car keeps moving even when the brakes are depressed.
Brakes got hard and went to the floor..almost crashed because brakes got hard and didn't stop the vehicle. Faulty brake booster..! Ford needs to recall these!
The contact owns a 2011 Ford Edge. The contact stated that while driving, the brake pedal had to be fully depressed before the brakes would engage. The contact stated that there was no warning light illuminated. The vehicle was diagnosed but not yet repaired. The manufacturer was not informed of the failure. The failure mileage …
Read full complaint
The contact owns a 2011 Ford Edge. The contact stated that while driving, the brake pedal had to be fully depressed before the brakes would engage. The contact stated that there was no warning light illuminated. The vehicle was diagnosed but not yet repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 204,504.
The “Vista” sunroof on my car is stuck open. This allows rain to come into my car providing hazardous driving conditions. The Ford dealer wants $4000 to repair & $500 to close. I’ve asked Ford several times for a detailed breakdown of costs, they have not provided anything to date.
No brake or ABS warning light. Brake pedal fades to floor with no braking until all the way at the floor. Almost rear ended car in front of me at red light. Problem is ABS module. Major safety issue.
Door ajar warning even though the door is closed. Doors will not lock and interior lights remain on.
Vehicle stahls about 50% time in reverse when parking mainly, and in forward when parking. Very scary and I have only had this vehicle for 1.5 months. Repairs have been made according to CEL codes; however, the stalling does not report the code, so it occurs over and over. Very scared this will happen and cause an accident. …
Read full complaint
Vehicle stahls about 50% time in reverse when parking mainly, and in forward when parking. Very scary and I have only had this vehicle for 1.5 months. Repairs have been made according to CEL codes; however, the stalling does not report the code, so it occurs over and over. Very scared this will happen and cause an accident. Based on numerous forums who had the same car and instance - it is the throttle body.
I have had a Soft brake pedal issue ever since I purchased the car in 2012. Because of the soft brake pedal the driving experience is awful. I do more coasting driving that actual driving sine I have to make room for the soft pedal to be applied. My heart sinks when I have to abruptly brake when cut off by another driver and the…
Read full complaint
I have had a Soft brake pedal issue ever since I purchased the car in 2012. Because of the soft brake pedal the driving experience is awful. I do more coasting driving that actual driving sine I have to make room for the soft pedal to be applied. My heart sinks when I have to abruptly brake when cut off by another driver and the brakes hesitate to react precisely. If it weren't for coasting I'd be in multiple accidents already. Instead I've put up with coasting driving experience which is a really horrible experience for me and the guy in back of me. I have had my brakes bled, pads and rotors changed multiple times to rectify the issue to no avail. I am addressing this issue because research suggests that it is a failed abs Hydraulic Unit and has described my braking situation perfectly. I've even had the situation temporarily fixed after an abs event, but it only last for less than a week then it goes back to being soft. This actually happened only one time. I believe this is a matter of safety and confidence behind the wheel which I have not benefited from since owning the vehicle.
Official recalls
311V128000 · Electrical System:software
Feb 24, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2011 FORD F-150, F-250, F-350, F-450, F-550, EDGE, AND LINCOLN MKX TRUCKS MANUFACTURED FROM OCTOBER 25, 2010, THROUGH NOVEMBER 20, 2010. THESE VEHICLES WERE INSPECTED USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) THAT HAD A CUSTOM SOFTWARE ROUTINE TO READ THE SUSPECT BODY CONTROL MODULE (BCM) SERIAL NUMBER. BASED ON THE SERIAL NUMBER THE BCM WAS EITHER NOT AFFECTED OR REPLACED. THE CUSTOM SOFTWARE ROUTINE WAS NOT READING THE CORRECT SET OF CHARACTERS, AND WAS NOT ABLE TO IDENTIFY A BCM THAT REQUIRED REPLACEMENT AFFECTED BCMS MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH COULD RESULT IN A VEHICLE FIRE.
Remedy: DEALER WILL INSPECT THE BODY CONTROL MODULE AND IF NECESSARY REPLACE IT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 7, 2011. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
10V659000 · Structure:body
Dec 29, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2011 F-150, F-250, F-350, F-450, F-550, EDGE AND LINCOLN MKX VEHICLES. DURING A SIX-DAY PRODUCTION PERIOD, THE SUPPLIER OF THE BODY CONTROL MODULE MANUFACTURED MODULES THAT MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH CAN RESULT IN AN UNATTENDED VEHICLE FIRE.
Remedy: DEALER WILL REPLACE THE BODY CONTROL MODULE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
10V516000 · Latches/locks/linkages:hatchback/liftgate:lock
Oct 27, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2011 EDGE AND LINCOLN MKX VEHICLES MANUFACTURED FROM JULY 1, 2010, THROUGH OCTOBER 8, 2010. THESE VEHICLES WERE SHIPPED WITH INCORRECTLY CONFIGURED ELECTRONIC MODULE SETTINGS THAT DISABLE THE LOCKING FUNCTION OF THE LIFTGATE. ACCORDINGLY, THE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS."
Consequence & remedy
Consequence: THE LIFTGATE LOCK MAY BE DISABLED AND THE DRIVER MAY NOT BE ABLE TO LOCK THE LIFTGATE USING INTERIOR LOCK SWITCHES OR REMOTE KEY FOB BUTTONS.
Remedy: FORD WILL NOTIFY OWNERS AND DEALERS WILL HAVE THE AFFECTED CONTROL MODULES UPDATED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 1, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.