← New search

2011 Ford Edge

Owner reports · Recalls · Investigations

More warning signs than most Edge years

Owner complaints for the 2011 Ford Edge are substantially higher than the model-year median of 724.

About this comparison →

When problems were reported

Mileage at the reported incident

1,438 reports with mileage · 363 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 686 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 274 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 261 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

23 crash reports4 fire reports7 injury reports

Service Brakes complaints

261 reports
Clear category filter
Mileage unknown · Oct 31, 2022
Service Brakes

Brake is extremely soft and must be pushed all the way to the floor to function. Both master cylinder and HCU were replaced with no correction to the problem. It is being inspected again.

NHTSA ODI #11491618

63,000 miles · Oct 27, 2022
Service Brakes

The contact’s daughter owns a 2011 Ford Edge. The contact stated that while the brake pedal was depressed, her daughter heard a hissing sound, and the brake pedal became difficult to depress without extra effort. The contact also stated that on multiple occasions while the brake pedal was depressed, the brake pedal intermittentl…

Read full complaint

The contact’s daughter owns a 2011 Ford Edge. The contact stated that while the brake pedal was depressed, her daughter heard a hissing sound, and the brake pedal became difficult to depress without extra effort. The contact also stated that on multiple occasions while the brake pedal was depressed, the brake pedal intermittently went to the floor. No warning lights were illuminated. The vehicle was taken to an independent mechanic to be diagnosed. The contact was informed that the brake booster needed to be replaced. The dealer was notified of the failure and the contact was informed that the vehicle was not covered under warranty. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was informed that there was no recall on the VIN. The manufacturer also confirmed that the vehicle was not under warranty. There was no further assistance provided. The failure mileage was approximately 63,000.

NHTSA ODI #11491137

70,000 miles · Oct 7, 2022
Service Brakes

The contact owns a 2011 Ford Edge. The contact stated that while operating the vehicle, the message "Service Brakes" was displayed. While depressing the brake pedal to stop the vehicle the pedal went to the floor and the braking distance was extended. The vehicle was taken to the local mechanic who replaced the rear brake pads. …

Read full complaint

The contact owns a 2011 Ford Edge. The contact stated that while operating the vehicle, the message "Service Brakes" was displayed. While depressing the brake pedal to stop the vehicle the pedal went to the floor and the braking distance was extended. The vehicle was taken to the local mechanic who replaced the rear brake pads. After retrieving the vehicle, while driving at an undisclosed speed, the vehicle was jerking while depressing the brake pedal. The cause of the failure was not yet determined. The local dealer was contacted and notified of the failure, but no assistance was offered. The manufacturer was not yet notified of the failure. The failure mileage was 70,000.

NHTSA ODI #11488375

Mileage unknown · Oct 4, 2022
Service Brakes

Had an issue when driving where I had to press all the way to the floor in order to brake. Checked fluid reservoir and it was empty. put brake fluid in, and it was ok for a couple of days. Now it's doing it again. The brake fluid is still in the reservoir so I don't know what the issue is. After reading forums and complaints, th…

Read full complaint

Had an issue when driving where I had to press all the way to the floor in order to brake. Checked fluid reservoir and it was empty. put brake fluid in, and it was ok for a couple of days. Now it's doing it again. The brake fluid is still in the reservoir so I don't know what the issue is. After reading forums and complaints, this seems to be an extremely common issue with Ford Edges. This is unsafe.

NHTSA ODI #11487858

Mileage unknown · Oct 3, 2022
Service Brakes

I noticed one morning driving to work that when I applied the brakes the pedal became a little bit harder to push to get the same amount of braking action. When I got to work I had the mechanic there take a look at the car because I was worried about driving it home. He checked all of the brake system and could not find a probl…

Read full complaint

I noticed one morning driving to work that when I applied the brakes the pedal became a little bit harder to push to get the same amount of braking action. When I got to work I had the mechanic there take a look at the car because I was worried about driving it home. He checked all of the brake system and could not find a problem. He took it for a test drive and said the brakes worked fine. I drove it home and no problem. A few days later I'm on the way to work and as I approached an intersection the light changed and I applied the brakes and this time the pedal went down closer to the floor and by the time I stopped my car was 1/2 way into the intersection. If a car had been in front of me I would have been in an accident. Again the mechanic looked it over and while he was driving it did it to him one time. He stated in his 45 years as a mechanic he had never seen one where the brakes work fine, then lose power brakes, and then they work fine for awhile. You can't know when it's going to happen. You can drive it for a week and it's fine and then it will do it. The mechanic did some checking and found out that Ford knows about the issue and offered a Customer satisfaction program where they extended the warranty coverage to 150,000 miles or 10 years. This car is a 2011 Ford Edge so it is 11 years old but it only has 98,000 miles. During the Covid 19 shutdown the car was hardly driven for 18 months. Ford says it's out of warranty. How is a failing brake booster NOT a safety recall? The mechanic said brake boosters rarely if ever need replacing and certainly not before 100,000 miles. I can't afford the cost of the repair because gas prices. Is it going to take people being killed in crashes before Ford is forced to recall the car? Brakes are the most important system on the car along with steering. The brake booster randomly not working increases the stopping distance and when it quits your reaction is to push real hard and then the brakes grab.

NHTSA ODI #11487700

Mileage unknown · Sep 28, 2022
Service Brakes

Valve inside Hydraulic Control Unit is sticking causing a soft and quickly fading brake pedal making it extremely difficult to stop quickly to avoid an accident. This is a serious problem.

NHTSA ODI #11487002

Mileage unknown · Aug 29, 2022
Service Brakes

Brakes must be pumped to make a good grab. My mechanic informed me several cars like mine have had the same issue. New master cylinder and booster are needed. Making this report in case this becomes an issue for other Ford Edge owners. The brakes have always been this way since I bought the vehicle, two years ago. The issue has …

Read full complaint

Brakes must be pumped to make a good grab. My mechanic informed me several cars like mine have had the same issue. New master cylinder and booster are needed. Making this report in case this becomes an issue for other Ford Edge owners. The brakes have always been this way since I bought the vehicle, two years ago. The issue has just gotten worse and I took it to my mechanic on the date listed below.

NHTSA ODI #11481724

80,000 miles · Aug 17, 2022
Back Over PreventionService Brakes

The contact owns a 2011 Ford Edge. The contact stated while her husband was driving at 20 MPH and coming to a stop, the brake pedal was depressed but failed to respond. The contact's husband pumped the brake pedal several times and the vehicle stopped. The contact stated that the failure reoccurred while driving. Additionally, t…

Read full complaint

The contact owns a 2011 Ford Edge. The contact stated while her husband was driving at 20 MPH and coming to a stop, the brake pedal was depressed but failed to respond. The contact's husband pumped the brake pedal several times and the vehicle stopped. The contact stated that the failure reoccurred while driving. Additionally, the contact stated that rearview camera image was distorted. The vehicle was taken to the dealer where it was diagnosed that the brake booster master cylinder and the rearview camera needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to NHTSA. The failure mileage was approximately 80,000.

NHTSA ODI #11479750

Mileage unknown · Aug 16, 2022
Service Brakes

I went to stop at Kwik Star and stepped on brake and there was significantly diminished stopping power. Because of the curbed sidewalk in front of the building was able to stop. The remainder of my trip home I allowed more stopping distance and was able to return vehicle to my house. I did call my local repair shop and the Po…

Read full complaint

I went to stop at Kwik Star and stepped on brake and there was significantly diminished stopping power. Because of the curbed sidewalk in front of the building was able to stop. The remainder of my trip home I allowed more stopping distance and was able to return vehicle to my house. I did call my local repair shop and the Power Brake Booster assembly was diagnosed as the issue and replaced on 8/12/2022. The mileage on my vehicle is 79963

NHTSA ODI #11479573

189,000 miles · Jun 15, 2022
Service Brakes

The contact owns a 2011 Ford Edge. The contact stated while driving approximately 20 MPH in moderately rainy conditions and coming to a stop, an unknown yellow warning light illuminated. The contact depressed the brake pedal and felt no braking power. The contact depressed the brake pedal to the floorboard. The contact said that…

Read full complaint

The contact owns a 2011 Ford Edge. The contact stated while driving approximately 20 MPH in moderately rainy conditions and coming to a stop, an unknown yellow warning light illuminated. The contact depressed the brake pedal and felt no braking power. The contact depressed the brake pedal to the floorboard. The contact said that the vehicle slid like it was on the ice. The contact started pumping the brake pedal and eventually recovered some braking power. The contact stated that the brake pedal was soft and she returned to the residence. The failure recurred and the contact drove the vehicle to a dealer. The dealer diagnosed the vehicle but was unable to duplicate the failure. The vehicle was not repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 189,000.

NHTSA ODI #11469466

Official recalls

3

11V128000 · Electrical System:software

Feb 24, 2011

FORD IS RECALLING CERTAIN MODEL YEAR 2011 FORD F-150, F-250, F-350, F-450, F-550, EDGE, AND LINCOLN MKX TRUCKS MANUFACTURED FROM OCTOBER 25, 2010, THROUGH NOVEMBER 20, 2010. THESE VEHICLES WERE INSPECTED USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) THAT HAD A CUSTOM SOFTWARE ROUTINE TO READ THE SUSPECT BODY CONTROL MODULE (BCM) SERIAL NUMBER. BASED ON THE SERIAL NUMBER THE BCM WAS EITHER NOT AFFECTED OR REPLACED. THE CUSTOM SOFTWARE ROUTINE WAS NOT READING THE CORRECT SET OF CHARACTERS, AND WAS NOT ABLE TO IDENTIFY A BCM THAT REQUIRED REPLACEMENT AFFECTED BCMS MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.

Consequence & remedy

Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH COULD RESULT IN A VEHICLE FIRE.

Remedy: DEALER WILL INSPECT THE BODY CONTROL MODULE AND IF NECESSARY REPLACE IT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 7, 2011. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.

10V659000 · Structure:body

Dec 29, 2010

FORD IS RECALLING CERTAIN MODEL YEAR 2011 F-150, F-250, F-350, F-450, F-550, EDGE AND LINCOLN MKX VEHICLES. DURING A SIX-DAY PRODUCTION PERIOD, THE SUPPLIER OF THE BODY CONTROL MODULE MANUFACTURED MODULES THAT MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.

Consequence & remedy

Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH CAN RESULT IN AN UNATTENDED VEHICLE FIRE.

Remedy: DEALER WILL REPLACE THE BODY CONTROL MODULE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT FORD AT 1-866-436-7332.

10V516000 · Latches/locks/linkages:hatchback/liftgate:lock

Oct 27, 2010

FORD IS RECALLING CERTAIN MODEL YEAR 2011 EDGE AND LINCOLN MKX VEHICLES MANUFACTURED FROM JULY 1, 2010, THROUGH OCTOBER 8, 2010. THESE VEHICLES WERE SHIPPED WITH INCORRECTLY CONFIGURED ELECTRONIC MODULE SETTINGS THAT DISABLE THE LOCKING FUNCTION OF THE LIFTGATE. ACCORDINGLY, THE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS."

Consequence & remedy

Consequence: THE LIFTGATE LOCK MAY BE DISABLED AND THE DRIVER MAY NOT BE ABLE TO LOCK THE LIFTGATE USING INTERIOR LOCK SWITCHES OR REMOTE KEY FOB BUTTONS.

Remedy: FORD WILL NOTIFY OWNERS AND DEALERS WILL HAVE THE AFFECTED CONTROL MODULES UPDATED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 1, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

PE16012 · Door Ajar Warning Light Always On

Opened Sep 28, 2016 · Closed Mar 20, 2017

Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Additional source detail variants (3)

Interior Lighting

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.