Every time I press the brakes, there is a hissing sound and the brake pedals go all the way to floor. This causes the vehicle to have low braking power and barely stop. The problem has been reproduced by an independent service center. There are no warning lamps or messages on the vehicle.
2011 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2011 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1,438 reports with mileage · 363 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 686 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 274 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 261 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
261 reportsThere is a CSP 13N02 regading an issue my vehicle currently experincing and is at the dealer for repairs. Im being told Ford issued this CSP for customers with the 2010-2014 Ford Edge but his VIN was not included. I'm being quoted out of pocket almost 2 grand for this repair. My Break pedal goes all the way down to the floor bed…
Read full complaint
There is a CSP 13N02 regading an issue my vehicle currently experincing and is at the dealer for repairs. Im being told Ford issued this CSP for customers with the 2010-2014 Ford Edge but his VIN was not included. I'm being quoted out of pocket almost 2 grand for this repair. My Break pedal goes all the way down to the floor bed having to put a lot of effort in stopping the vehicle. Per the CSP 13N02 If your vehicle is not serviced, the tear will eventually expand and the pedaleffort required to stop the vehicle will gradually increase. However, in all cases, the fundamental vehicle braking system remains functional. In the interest of customer satisfaction, Ford Motor Company is extending. The limited warranty on the brake booster to ten (10) years or 150,000 miles from the warranty start date of your vehicle, whichever occurs first. This is a one-time repair program. If your vehicle has already exceeded the mileage limit, this coverage will last through November 30, 2025.
My brakes pedal was going down and I called w.w. auto where I got it from and he said it sounded like a master brake cylinder and he came and got it said he replaced it but 3 weeks later it did it again and he told me to take it to Roberts garage and he said he called them and said the part he bought from AutoZone had a life tim…
Read full complaint
My brakes pedal was going down and I called w.w. auto where I got it from and he said it sounded like a master brake cylinder and he came and got it said he replaced it but 3 weeks later it did it again and he told me to take it to Roberts garage and he said he called them and said the part he bought from AutoZone had a life time warranty and he took them the receipt and got a replacement for the part and they kept my vehicle 2 days and said they bleed them and said there was air in the brake line and told me to bring it back if it did it again and he would put the new part on and I'M GOING TO take it back because it doesn't feel right why did they not have put the replacement part on ? Do you have any suggestions
The brake pedal goes to the floor with no warning. It has happened many times before. I'm on my second master cylinder, it has all new brake pads and calipers all the way around. It has been in the shop 4 times and no one can figure out what is causing this. There are no leaks and all the rubber hoses are in good shape.
The Ford Edge has a known and documented issue with the brake booster failing and having to be replaced numerous times. I recently had to apply my brakes suddenly to avoid a collision with a car that cut me off. After noticed the brakes lost pressure and appear to be compromised. This is the second time this has happened after a…
Read full complaint
The Ford Edge has a known and documented issue with the brake booster failing and having to be replaced numerous times. I recently had to apply my brakes suddenly to avoid a collision with a car that cut me off. After noticed the brakes lost pressure and appear to be compromised. This is the second time this has happened after already replacing the same brake booster issue less than 3 years ago. While looking online this appears to be an ongoing problem with this make and model but has not been addressed by the manufacturer. This causes safety issues and repetitive - expensive repair issues.
Got my car serviced at AAA Car Care Center. After completed the brakes did not work properly, brought the vehicle back and it was checked thoroughly. AAA came to the conclusion that the brake booster completely failed, all other components of the brake system were checked and working properly. Manager of AAA explained this is a …
Read full complaint
Got my car serviced at AAA Car Care Center. After completed the brakes did not work properly, brought the vehicle back and it was checked thoroughly. AAA came to the conclusion that the brake booster completely failed, all other components of the brake system were checked and working properly. Manager of AAA explained this is a Ford only issue and that it was a common issue with my model. My safety and the safety of others were put at risk as I almost crashed into the back of a car stopped at a light. The problem of the brake booster was confirmed by AAA Car Care Center in Tampa, FL. Vehicle has not been inspected by manufacturer, police, insurance representatives or others. There were no warning lamps or messages prior to the failure.
The contact owns a 2011 Ford Edge. The contact stated that while his son was driving at an undisclosed speed, the brake pedal locked and was inoperable. Due to the brake pedal failure, the vehicle crashed into a nearby curb. The contact stated that his son described the brake pedal as it was hard as a brick. The damage done to …
Read full complaint
The contact owns a 2011 Ford Edge. The contact stated that while his son was driving at an undisclosed speed, the brake pedal locked and was inoperable. Due to the brake pedal failure, the vehicle crashed into a nearby curb. The contact stated that his son described the brake pedal as it was hard as a brick. The damage done to the vehicle due to the brake pedal failure was diagnosed and repaired by the contact. The damages were a fractured passenger front side lower control arm and a fractured front passenger front side drive axle. The vehicle was towed to the dealer and diagnosed with a failed brake booster and failed brake master cylinder. The brake booster and brake master cylinder needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure, however, the contact was informed that the vehicle was not covered under the recall. The failure mileage was approximately 243,000.
While coming to a stop, the brake pedal became very hard to depress. After taking it to a service facility, they determined it was the brake power booster and I should have received a service advisory from Fordabout this potential failure with this part. Never received anything about this problem from Ford and after reviewing th…
Read full complaint
While coming to a stop, the brake pedal became very hard to depress. After taking it to a service facility, they determined it was the brake power booster and I should have received a service advisory from Fordabout this potential failure with this part. Never received anything about this problem from Ford and after reviewing this problem with other owners on the internet, other people experienced the same problem. It is obvious Ford knows this is a faulty part and is putting people at risk of getting killed without a recall.
13N02 – Extended Warranty Coverage on Brake Booster – 2010-2013 Ford Edge & Lincoln MKX. My break booster required repair and when I went to the dealership and called Ford they stated that the vehicle had to have less than 150,000 miles and it is not 10 years old which ever comes 1st. The break boosters are starting to fail on…
Read full complaint
13N02 – Extended Warranty Coverage on Brake Booster – 2010-2013 Ford Edge & Lincoln MKX. My break booster required repair and when I went to the dealership and called Ford they stated that the vehicle had to have less than 150,000 miles and it is not 10 years old which ever comes 1st. The break boosters are starting to fail on cars with less than 150,000 miles, but older than 10 years. This is causing a driving hazard as the breaks went out while driving.
The contact owns a 2011 Ford Edge. The contact stated that while driving at an undisclosed speed and depressing the brake pedal, the brake pedal was firm. The contact stated that the braking distance was extended and there was an abnormal sound coming from the brakes while depressed. No warning light was illuminated. The vehicle…
Read full complaint
The contact owns a 2011 Ford Edge. The contact stated that while driving at an undisclosed speed and depressing the brake pedal, the brake pedal was firm. The contact stated that the braking distance was extended and there was an abnormal sound coming from the brakes while depressed. No warning light was illuminated. The vehicle was diagnosed, and the brake failure was confirmed. The vehicle was not repaired. The manufacturer was made aware of the failure and the contact was advised to contact the NHTSA Hotline. The failure mileage was approximately 140,000.
Official recalls
311V128000 · Electrical System:software
Feb 24, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2011 FORD F-150, F-250, F-350, F-450, F-550, EDGE, AND LINCOLN MKX TRUCKS MANUFACTURED FROM OCTOBER 25, 2010, THROUGH NOVEMBER 20, 2010. THESE VEHICLES WERE INSPECTED USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) THAT HAD A CUSTOM SOFTWARE ROUTINE TO READ THE SUSPECT BODY CONTROL MODULE (BCM) SERIAL NUMBER. BASED ON THE SERIAL NUMBER THE BCM WAS EITHER NOT AFFECTED OR REPLACED. THE CUSTOM SOFTWARE ROUTINE WAS NOT READING THE CORRECT SET OF CHARACTERS, AND WAS NOT ABLE TO IDENTIFY A BCM THAT REQUIRED REPLACEMENT AFFECTED BCMS MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH COULD RESULT IN A VEHICLE FIRE.
Remedy: DEALER WILL INSPECT THE BODY CONTROL MODULE AND IF NECESSARY REPLACE IT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 7, 2011. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
10V659000 · Structure:body
Dec 29, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2011 F-150, F-250, F-350, F-450, F-550, EDGE AND LINCOLN MKX VEHICLES. DURING A SIX-DAY PRODUCTION PERIOD, THE SUPPLIER OF THE BODY CONTROL MODULE MANUFACTURED MODULES THAT MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH CAN RESULT IN AN UNATTENDED VEHICLE FIRE.
Remedy: DEALER WILL REPLACE THE BODY CONTROL MODULE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
10V516000 · Latches/locks/linkages:hatchback/liftgate:lock
Oct 27, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2011 EDGE AND LINCOLN MKX VEHICLES MANUFACTURED FROM JULY 1, 2010, THROUGH OCTOBER 8, 2010. THESE VEHICLES WERE SHIPPED WITH INCORRECTLY CONFIGURED ELECTRONIC MODULE SETTINGS THAT DISABLE THE LOCKING FUNCTION OF THE LIFTGATE. ACCORDINGLY, THE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS."
Consequence & remedy
Consequence: THE LIFTGATE LOCK MAY BE DISABLED AND THE DRIVER MAY NOT BE ABLE TO LOCK THE LIFTGATE USING INTERIOR LOCK SWITCHES OR REMOTE KEY FOB BUTTONS.
Remedy: FORD WILL NOTIFY OWNERS AND DEALERS WILL HAVE THE AFFECTED CONTROL MODULES UPDATED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 1, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration